Yamaha MG10XU/MG10 Specifications

Yamaha Analog Mixers Specifications - MG10XU/MG10.
Download
Page  of 2
4.1, 1836 votes
background image

General Specifications
0 dBu = 0.775 Vrms Output impedance of signal generator (Rs) = 150Ω
All level knobs are nominal if not specified.

Frequency Response

Input to STEREO OUT

+0.5 dB/-1.0 dB (20 Hz to 48 kHz),  
refer to the nominal output level @1 kHz, GAIN knob: Min

Total Harmonic Distortion 
(THD+N)

Input to STEREO OUT

 

0.02 %  @ +14 dBu (20 Hz to 20 kHz), GAIN knob: Min  

 

0.003 %  @ +24 dBu (1 kHz), GAIN knob: Min

Hum&Noise *1
(20 Hz to 20 kHz)

Equivalent Input Noise

-128 dBu (Mono Input Channel, Rs: 150 Ω, GAIN knob: Max)

Residual Output Noise

-102 dBu (STEREO OUT, STEREO LEVEL knob: Min)

Crosstalk (1 kHz) *2

-83 dB

Input Channels

10 channels:  Mono [MIC/LINE]: 4, Stereo [LINE]: 3

Ouput Channels

STEREO OUT: 2, PHONES: 1, MONITOR OUT: 1, AUX (FX) SEND: 1

Bus

Stereo: 1, AUX (FX): 1

Input Channel Function

PAD

CH1 – CH4

26 dB

HPF 

CH1 – CH4

80 Hz, 12 dB/oct

COMP

CH1 – CH2

1-knob compressor  
Threshold: +22 dBu to -8 dBu, Ratio:1:1 to 4:1,  
Output level: 0 dB to 7 dB, Attack time: approx. 25 msec,  
Release time: approx. 300 msec

EQ

CH1 – CH9/10 HIGH:  Gain: +15 dB/-15 dB, Frequency: 10 kHz shelving
CH1 – CH4

MID:  Gain: +15 dB/-15 dB, Frequency: 2.5 kHz peaking

CH1 – CH9/10 LOW:  Gain: +15 dB/-15 dB, Frequency: 100 Hz shelving

PEAK LED

CH1 – CH4

LED turns on when post EQ signal reaches 3 dB below 
clipping (+17 dBu)

Level Meter

Post STEREO LEVEL 
Knob

2×7 -segment LED meter [PEAK (+17), +10, +6, 0, -6, -10, -20 dB]

Internal Digital Effect  
(MG10XU)

SPX Algorithm

24 programs

USB Audio (MG10XU)

2 IN / 2 OUT

USB Audio Class 2.0 compliant
Sampling Frequency: Max 192 kHz, Bit Depth: 24-bit

Phantom Power Voltage

+48 V

Power Supply Adaptor

PA-10 (AC 38 VCT, 0.62A, Cable length = 3.6 m)  
or equivalent recommended by Yamaha

Power Consumption

22.9 W

Dimensions (W×H×D)

244 mm×71 mm×294 mm (9.6” × 2.8” × 11.6”)

Net Weight

MG10XU: 2.1 kg (4.6 lbs.), MG10: 1.9 kg (4.1 lbs.)

Included Accessory

AC Adaptor, Cubase AI Download Information (MG10XU),  
Owner’s Manual, Precautions, Technical Specifications (this leaflet)

Optional Accessory

Mic Stand Adaptor: BMS-10A

Operating Temperature

0 to +40°C

*1 Noise is measured with A-weighting filter. *2 Crosstalk is measured with 1 kHz band pass filter.

Analog Input Characteristics

Input Jacks

PAD  

26 dB

GAIN  

Trim  

Position

Actual 

Load  

Impedance

For Use 

With  

Nominal

Input level

Connector

Sensitivity *1

Nominal

Max. before 

clip

 MIC/LINE 1 – 4

OFF

+64 dB

3 kΩ

50-600 Ω

Mics/Lines

-72 dBu

(0.195 mV)

-60 dBu

(0.775 mV)

-40 dBu

(7.75 mV)

Combo jack*2  

(Balanced)

+20 dB

-28 dBu

(30.9 mV)

-16 dBu

(122.8 mV)

+4 dBu

(1.228 mV)

ON

+38 dB

-46 dBu

(3.884 mV)

-34 dBu

(15.46 mV)

-14 dBu

(154.6 mV)

-6 dB

-2 dBu

(615.6 mV)

+10 dBu

(2.451 V)

+30 dBu
(24.51 V)

LINE 5/6, 7/8

-

-

10 kΩ

600 Ω Lines

-22 dBu

(61.56 mV)

-10 dBu

(245.1 mV)

+10 dBu

(2.451 V)

Phone jack *3  

RCA Pin  

(Unbalanced)

LINE 9/10

Phone jack *3  
(Unbalanced)

0 dBu is referenced to 0.775 Vrms.
*1 Sensitivity is the lowest level that will produce an output of +4dBu (1.228V) or the nominal output level when the unit is set to maximum gain (all level knobs are 

maximum position).
*2 1&Sleeve = Ground, 2&Tip = Hot, 3&Ring = Cold
*3 Tip = Signal, Sleeve = Ground

Analog Output Characteristics

Output Terminals

Actual Source 

Impedance

For Use With  

Nominal

Output level

Connector

Nominal

Max. before clip

 STEREO OUT [L, R]

75 Ω

600 Ω Lines

+4 dBu

(1.228 V)

+24 dBu

(12.28 V)

XLR-3-32 *1

Phone jack *2

(Balanced)

MONITOR OUT [L, R]  

AUX (FX) SEND

150 Ω

10 kΩ Lines

+4 dBu

(1.228 V)

+20 dBu
(7.750 V)

Phone jack *2

(Impedance Balanced)

 PHONES 

110 Ω

40 Ω Lines

3 mW + 3 mW

100 mW + 100 mW

Stereo phone jack

0 dBu is referenced to 0.775 Vrms.
*1 1 = Ground, 2 = Hot, 3 = Cold
*2 Tip = Hot, Ring = Cold, Sleeve = Ground

Digital Input / Output Characteristics

Output Terminals

Format

Data Length*1

Fs

Connector

USB

USB Audio Class 2.0

16 /24 bit

44.1 kHz, 48 kHz, 88.2 kHz,  
96 kHz, 176.4 kHz, 192 kHz

USB Standard-B

*1 Data length depends on the particular audio format being used. USB Audio Class2.0: 16 / 24-bit, Yamaha Steinberg USB Driver: 24-bit

European Models
Inrush Current based on EN 55103-1:2009
1 A (on initial switch-on)
1 A (after a supply interruption of 5s)
Conforms to Environments: E1, E2, E3 and E4

Specifications and descriptions in this document are for informational purposes only. Yamaha Corporation reserves the right to modify products or specifications at 

any time without prior notice. Since specifications, equipment, and options may not be the same in every locale, please check with your Yamaha dealer.

ZJ12600

MIXING CONSOLE

Technical Specifications

See reverse side for block/level diagrams and dimensions.

Also See for Yamaha MG10XU/MG10

0.645543s