White Rodgers 1131-102 Well Immersion Single Control Installation Instructions
WHITE-RODGERS DIVISION
EMERSON ELECTRIC CO.
9797 REAVIS RD., ST. LOUIS, MO. 63123
(314) 577-1300,
FAX (314) 577-1517
9999 HWY. 48, MARKHAM, ONT. L3P 3J3
(905) 475-4653, FAX (905) 475-4625
Printed in U.S.A.
FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY BEFORE
INSTALLING OR OPERATING THIS CONTROL COULD CAUSE PERSONAL
INJURY AND/OR PROPERTY DAMAGE.
Type 1131 controls are designed for use on hot water
heating installations. They have single-pole, double-throw
switch action, offering open-on-rise terminals as well as
close-on-rise terminals. These controls may be used as a
high limit, low limit, circulator, or combination low limit-
circulator control.
Models are available with either horizontal or vertical well,
and with either fixed or adjustable differential. Some of
these models also have excess capillary stored within the
enclosure, permitting them to be used with wells having
either a standard or extended shank.
Another model, ideal for replacement purposes, has both
a slotted case and excess capillary stored within the
enclosure. This control can be used with either a standard
or extended shank well, on either horizontal or vertical
well installations.
DESCRIPTION
TYPE 1131
HOT WATER CONTROL
S.P.D.T. Well-Immersion
INSTALLATION INSTRUCTIONS
CAUTION
WARNING
THIS CONTROL MUST BE INSTALLED BY A
QUALIFIED INSTALLER.
Do not exceed the specification ratings.
All wiring must conform to local and national electrical
codes and ordinances.
This control is a precision instrument, and should be
handled carefully. Rough handling or distorting compo-
nents could cause the control to malfunction.
This control has been accurately calibrated at the factory.
Any attempt to calibrate this control will void the White-
Rodgers warranty.
PRECAUTIONS
CONVERTIBLE CONTROLS
Convertible controls have a Knockout Plate on back of
case (secured by Hex Nut on Horizontal models, and by
Knockout Plug on Vertical models). To convert from
Horizontal to Vertical:
1. Remove control cover. Then remove bottom knockout.
2. Remove Hex Nut (inside control) from Well Mounting
Stem. (To loosen, hold Hex Nut inside while turning
Hex Nut on back of control counterclockwise.)
3. Pull Well Mounting Stem away from case and remove
Knockout Plate.
4. Swing capillary down through slot into bottom knock-
out.
5. Secure Knockout Plate to back of case by using
Knockout Plug provided in envelope.
6. Insert Well Mounting Stem into bottom knockout and
tighten Hex Nut (inside control) securely.
WHITE-RODGERS
Operator: Save these instructions for future use!
PART NO. 37-2071B
Replaces 37-2071 & 37-9195
9548
Do not use on circuits exceeding specified
voltages. Higher voltages will damage control
and could cause shock or fire hazard.
To prevent electrical shock and/or equipment
damage, disconnect electric power to system, at
main fuse or circuit breaker box, until installation
is complete.
Also See for White Rodgers 1131-102 Well Immersion Single Control
Related Manuals for White Rodgers 1131-102 Well Immersion Single Control
-
White Rodgers Hydronic & Appliance 1050-1 Indoor/Outdoor Indoor-Outdoor Control Installation Instructions
10 pages
-
White Rodgers Hydronic & Appliance 1127-9 Surface (Strap-On) Hydronic Temperature Control Installation Instructions
6 pages
-
White Rodgers Hydronic & Appliance 1131-102 Well Immersion Single Control Catalog Page
1 pages
-
White Rodgers Hydronic & Appliance 1145-33 Fast Response Direct Immersion Hydronic Controls Installation Instructions
4 pages
-
White Rodgers Hydronic & Appliance 11B05-101 Well Immersion Hydronic Control Installation Instructions
4 pages
-
White Rodgers Hydronic & Appliance 11B06-1 Remote Bulb Hydronic Control Installation Instructions
4 pages
-
White Rodgers Hydronic & Appliance 11B18-101 Well Immersion Hydronic Control Catalog Page
1 pages
-
White Rodgers Hydronic & Appliance 11B18-101 Well Immersion Hydronic Control Installation Instructions
6 pages
-
White Rodgers Hydronic & Appliance 11B18-153 Well Immersion Hydronic Control Installation Instructions
6 pages
-
White Rodgers Hydronic & Appliance 11D18-1 Well Immersion Single Control Installation Instructions
6 pages
-
White Rodgers Hydronic & Appliance 11D31-1 Well Immersion Single Control Installation Instructions
6 pages
-
White Rodgers Hydronic & Appliance 1311-102 Hydronic Zone Controls Troubleshooting
1 pages
-
White Rodgers Hydronic & Appliance 1311-103 Hydronic Zone Controls Installation Instructions
8 pages
-
White Rodgers Hydronic & Appliance 1311-103 Hydronic Zone Controls Troubleshooting
1 pages
-
White Rodgers Hydronic & Appliance 1311-104 Hydronic Zone Controls Catalog Page
1 pages
-
White Rodgers Hydronic & Appliance 1361-102 Hydronic Zone Controls Supplemental Wiring
2 pages
-
White Rodgers Hydronic & Appliance 1361-103 Hydronic Zone Controls Catalog Page
1 pages
-
White Rodgers Hydronic & Appliance 1361-103 Hydronic Zone Controls Troubleshooting
1 pages
-
White Rodgers Hydronic & Appliance 25M01A-100 25M Gas Dryer Valves Specification Sheet
2 pages
-
White Rodgers Hydronic & Appliance 25M01A-101 25M Gas Dryer Valves Installation Instructions
4 pages
-
White Rodgers Hydronic & Appliance 25M01A-101 25M Gas Dryer Valves Specification Sheet
2 pages
-
White Rodgers Hydronic & Appliance 37C72U-185 Gas Water Heater Control for LP Gas (Left Hand Threads) Catalog Page
1 pages
-
White Rodgers Hydronic & Appliance 37C73U-168 Gas Water Heater Control for Natural Gas Installation Instructions
4 pages
-
White Rodgers Hydronic & Appliance 37E73A-903 Intelli-Vent Control for Power Vented Water Heaters Installation Instructions
8 pages