Whirlpool WFW8300SW1 Use & Care Manual | Page 4

Whirlpool Washers Use & Care Manual - WFW8300SW1.
Download
Page  of 52
4.8, 2061 votes
background image

4

INSTALLATION REQUIREMENTS

Tools and Parts

Gather the required tools and parts before starting installation. 
The parts supplied are in the washer drum. 

Tools needed for connecting the water inlet hoses 

Pliers (that open to 1

⁹⁄₁₆" [39.5 mm]) 

Flashlight (optional)

Tools needed for installation

Open end wrenches 14 mm and 13 mm

Level

Wood block 

Ruler or measuring tape

Parts supplied 

Alternate Parts
Your installation may require additional parts. If you are interested 
in purchasing one of the items listed here, call the toll-free 
number on the cover or in the “Assistance or Service” section. 

Options

Pedestal

You have the option of purchasing pedestals of different heights 
separately for this washer. You may select a 10" (25.4 cm) or a 
15.5" (39.4 cm) pedestal. The pedestal will add to the total height 
of the washer. 

Optional pedestal 

Stack Kit

Are you planning to stack your washer and dryer? To do so you 
will need to purchase a Stack Kit.

To order, call the dealer from whom you purchased your washer 
or refer to the “Assistance or Service” section of this manual. Ask 
for Part Number 8572546.

Location Requirements

Selecting the proper location for your washer improves 
performance and minimizes noise and possible washer “walk.”

Your washer can be installed under a custom counter, or in a 
basement, laundry room, closet, or recessed area. See “Drain 
System.”

Companion appliance location requirements should also be 
considered. Proper installation is your responsibility.

You will need

A water heater set to deliver 120°F (49°C) water to the washer.

A grounded electrical outlet located within 6 ft (1.8 m) of 
where the power cord is attached to the back of the washer. 
See “Electrical Requirements.”

Hot and cold water faucets located within 4 ft (1.2 m) of the 
hot and cold water fill valves, and water pressure of 
20-100 psi (137.9-689.6 kPa).

A level floor with a maximum slope of 1" (2.5 cm) under entire 
washer. Installing the washer on soft floor surfaces, such as 
carpets or surfaces with foam backing, is not recommended.

A sturdy and solid floor to support the washer with a total 
weight (water and load) of 400 lbs (180 kg).

Do not operate your washer in temperatures below 32°F (0°C). 
Some water can remain in the washer and can cause damage in 
low temperatures.

A. U-shaped hose form
B. Water inlet hoses (2)

C. Inlet hose washers (4)

D. Transit bolt hole 

plug (4)

E. Beaded tie strap

If You Have

You Will Need to Buy

Laundry tub or 
standpipe taller 
than 96" (2.4 m)

Sump pump system (if not already 
available)

Overhead sewer

Standard 20 gal. (76 L), 30" (76.2 cm) tall 
drain tub or utility sink and sump pump 
(available from local plumbing suppliers)

Floor drain

Siphon break, Part Number 285834; 
additional drain hose 
Part Number 8318155; and connector kit, 
Part Number 2858835 

Drain hose too 
short

4 ft (1.2 m) drain hose extension kit, 
Part Number 2858863

Water faucets 
beyond reach of fill 
hoses

2 longer water fill hoses: 
6 ft (1.8 m) Part Number 76314
10 ft (3.0 m) Part Number 350008

A

B

C

D

E

Pedestal 
Height

Approximate 
Height with
Washer

Color

Model
Number

10" (25.4 cm)

46" (116.8 cm)

White

WHP1000SQ

15.5" (39.4 cm)

51.5" (130.8 cm)

White

WHP1500SQ

 

0.504912s