Whirlpool WDT730PAHV Dimension Guide

Dishwasher with Fan Dry
Download
Page  of 2
4.7, 1835 votes
background image

Undercounter Dishwasher

PRODUCT MODEL NUMBERS

WDF110PAB 

WDF111PAB 

WDF120PAF 

WDF121PAF 

WDF130PAH 

WDF131PAH

WDF320PAD 

WDF330PAH 

WDF331PAH 

WDF520PAD 

WDF540PAD 

WDF545PAF

WDT710PAH 

WDT720PAD 

WDT730PAH 

WDT735PAG 

WDT735PAH

DRAIN REQUIREMENTS

 

A new drain hose is supplied with your dishwasher. If drain 

hose is not long enough, use a new drain hose with a 

maximum length of 12 ft (3.7 m) that meets all current AHAM/

IAPMO test standards, is resistant to heat and detergent, and 

fits the 1" (25 mm) drain connector of the dishwasher. See 

the “Tools and Parts” section at the front of the guide for part 

details and orders.

 

Make sure to connect drain hose to waste tee or disposer 

inlet above drain trap in house plumbing and 20" (508 mm) 

minimum above the floor. It is recommended that the drain 

hose either be looped up and securely fastened to the 

underside of the counter or be connected to an air gap.

 

Make sure to use an air gap if the drain hose is connected 

to house plumbing lower than 20" (508 mm) above 

subfloor or floor.

 

If required, the air gap should be installed in accordance 

with the air gap installation instructions. When you are 

connecting the air gap, a rubber hose (not provided) will 

be needed to connect to the waste tee or disposer inlet.

 

Use 1/2" minimum I.D. drain line fittings.

WATER SUPPLY REQUIREMENTS

 

This dishwasher has a water heating feature and also  

requires a connection to a hot water supply line.

 

A hot water line with 20 to 120 psi (138 to 862 kPa) water  

pressure can be verified by a licensed plumber.

 

120°F (49°C) water at dishwasher

 

■ 3

/8" O.D. copper tubing with compression fitting or flexible 

braided water supply line. See the “Tools and Parts” section 

at the front of the guide for part details and orders.

NOTE: 1/2" minimum plastic tubing is not recommended.

 

A 90° elbow with 3/4" hose connection with rubber washer.  

See the “Tools and Parts” section at the front of the guide 

for part details and orders.

 

Do not solder within 6" (152 mm) of the water inlet valve.

 

If installed in new construction, make sure the house 

water supply lines have been flushed prior to connecting 

the dishwasher to remove any debris that may exist in 

the supply line.

NOTE: If replacing an existing dishwasher, it is recommended  

to install a new water line (see the “Tools and Parts” section at 

the front of the guide for part details) and drain hose (supplied) 

with the new dishwasher.

ELECTRICAL REQUIREMENTS

You Must Have:

 

120-volt, 60 Hz, AC-only, 15- or 20-amp, fused  

electrical supply

 

Copper wire only

 

A maximum of 2 field wiring supply conductors 

(12 AWG largest size) plus 1 grounding conductor  

are permitted in the terminal box.

We Recommend:

 

A time-delay fuse or circuit breaker

 

A separate circuit

If Connecting Dishwasher with a Power Cord:

 

Use a UL Listed power cord kit marked for 

use with dishwasher. See the “Tools and 

Parts” section at the front of the guide for  

part details and orders.

 

Plug into a grounded 3 prong outlet. Outlet  

must meet all local codes and ordinances.

If Connecting Dishwasher with Direct Wiring:

 

Use flexible, armored, or nonmetallic 

sheathed copper wire with grounding wire 

that meets the wiring requirements for 

your home and local codes and ordinances.

 

Use a UL Listed/CSA Approved metallic strain relief. 

Use of air gap

Air gap

Because Whirlpool Corporation policy includes a continuous commitment 

to improve our products, we reserve the right to change materials and 

specifications without notice.

Dimensions are for planning purposes only. For complete details, see 

Installation Instructions packed with product. Specifications subject to 

change without notice.

Page 1 of 2 

W10806908-D-WH

12/16

0.701151s