Whirlpool Refrigerator ED5JHGXRB01 User's Manual | Page 7

Whirlpool Refrigerators User's Manual - Refrigerator ED5JHGXRB01.
Download
Page  of 44
4.2, 2108 votes
background image

7

After connecting the refrigerator to a water source, flush the 
water system by dispensing water into a sturdy container until 
you draw and discard 1.5 gal. (5.4 L) of water, or for 
approximately 3 minutes after the water begins dispensing. 
The flushing process cleans the water system and clears air 
from the lines. As the air is cleared from the lines, water may 
spurt out of the dispenser. 

Allow several hours for the refrigerator to cool down and chill 
water.

Allow 24 hours to produce the first batch of ice. Discard the 
first three batches of ice produced.

The Water Dispenser

IMPORTANT: Dispense enough water every week to maintain a 
fresh supply.
To Dispense Water:
1. 
Press a sturdy glass against the water dispenser lever.
2. Remove the glass to stop dispensing.

The Ice Dispenser

The dispensing system will not operate when the freezer door is 
open. Ice dispenses from the ice maker storage bin in the freezer 
when the dispenser lever is pressed.
NOTE: Some models dispense both cubed and crushed ice. 
Before dispensing ice, select which type of ice you prefer. 
For crushed ice, cubes are crushed before being dispensed. This 
may cause a slight delay when dispensing crushed ice. Noise 
from the ice crusher is normal, and pieces of ice may vary in size. 
When changing from crush to cube, a few ounces of crushed ice 
will be dispensed along with the first cubes.
To Dispense Ice:
1. 
Press the button to select the desired type of ice.
2. Press a sturdy glass against the ice dispenser lever. Hold the 

glass close to the dispenser opening so ice does not fall 
outside of the glass. 
IMPORTANT: You do not need to apply a lot of pressure to the 
lever in order to activate the ice dispenser. Pressing hard will 
not make the ice dispense faster or in greater quantities.

3. Remove the glass to stop dispensing.

The Dispenser Light

Style 1: The dispenser light can be turned on by pressing the ON 
button.
Style 2: When you use the dispenser, the lever will automatically 
turn the light on. If you want the light to be on continuously, you 
may choose either ON or NIGHT LIGHT. 
ON: Press the LIGHT button to turn on the dispenser light. 
NIGHT LIGHT: Press the LIGHT button a second time to select 
the Night Light. The dispenser light will automatically adjust to 
become brighter as the room brightens, dimmer as the room 
darkens.
OFF: Press the LIGHT button a third time to turn off the dispenser 
light.
The dispenser lights are LEDs which should not need to be 
changed. If it appears that your dispenser lights are not working, 
be sure that the light sensor is not blocked (in Night Light mode). 
See “Troubleshooting” for more information. 

The Dispenser Lock (on some models)

Your dispenser can be turned off for easy cleaning or to prevent 
unintentional dispensing by small children and pets. 
NOTE: The lock feature does not shut off power to the product, to 
the ice maker, or to the dispenser light. It simply deactivates the 
dispenser levers. The ice and water dispensers will not work.
Style 1: Press the LOCK button to lock the dispenser. Press the 
UNLOCK button to unlock the dispenser. 
Style 2: Press and hold the LOCK OUT button to lock the 
dispenser. Press and hold the LOCK OUT button a second time to 
unlock the dispenser. 

Ice Maker and Storage Bin

Turning the Ice Maker On/Off

The ON/OFF switch is located on the top right-hand side of the 
freezer compartment.
To turn on the ice maker, slide the control to the ON (left) position.
To manually turn off the ice maker, slide the control to the OFF 
(right) position.
NOTE: Your ice maker has an automatic shutoff. The ice maker 
sensors will automatically stop ice production, but the control will 
remain in the ON (left) position.
REMEMBER:

Allow 24 hours to produce the first batch of ice. Discard the 
first three batches of ice produced.

The quality of your ice will be only as good as the quality of the 
water supplied to your ice maker. Avoid connecting the ice 
maker to a softened water supply. Water softener chemicals 
(such as salt) can damage parts of the ice maker and lead to 
poor quality ice. If a softened water supply cannot be avoided, 
make sure the water softener is operating properly and is well 
maintained.

Do not use anything sharp to break up the ice in the storage 
bin. This can cause damage to the ice container and the 
dispenser mechanism.

Do not store anything on top of or in the ice maker or storage 
bin.

Removing and Replacing Ice Storage Bin

1. Hold the base of the storage bin with both hands and press 

the release button to lift the storage bin up and out.
NOTE: It is not necessary to turn the ice maker control to the 
OFF (right) position when removing the storage bin. The 
sensor cover (“flipper door”) on the left wall of the freezer 
stops the ice maker from producing ice if the door is open or 
the storage bin is removed.

2. Replace the storage bin on the door and push down to make 

sure it is securely in place.

Related Manuals for Whirlpool Refrigerator ED5JHGXRB01

0.501007s