Westinghouse One-Light Flush-Mount Outdoor Lantern 6691900 Instruction Manual

Westinghouse Outdoor Fixtures Instruction Manual - One-Light Flush-Mount Outdoor Lantern 6691900.
Download
Page  of 2
4.5, 2397 votes
background image

MOUNTING AND WIRING INSTRUCTIONS
NOTE: Underwriters Laboratories (UL) does not require all fixtures to have ground wires.  These fixtures 

meet all UL specifications.
CAUTION: For fixtures labeled for outdoor and wet location use, provide a water-tight seal between 

the fixture and the mounting surface by using silicone or similar caulking.
1.     Turn off power at circuit box to avoid possible electric shock.

2.   Thread mounting screws (A) into mounting bar (B) approximately 5/8 inch (see fig. 1).

3.   Secure mounting bar (B) to outlet box (C) with outlet box screws (D) (if applicable).

4.   Thread wires up through center hole (E) in mounting bar (B.)

5.   Identify color coding of fixture wires (see figure 2).

6.   To connect wires, take black fixture wire (group A from fig. 2) and place evenly against black outlet  

      box wire. Do not twist wires.

7.   Fit wire connector (F from fig. 1) over wires and twist until there is a firm connection. If wire 

      connector (F) easily comes off, reattach and check again for a firm connection (see figure 1).

8.   Repeat steps 5, 6 and 7 with the white (group B from fig. 2) fixture and outlet box wires.

9.   Partially thread green grounding screw (G) into side hole (H) on mounting bar (B) (see fig. 1).

10. Wrap ground wire from fixture around green grounding screw (G) leaving enough excess wire, 

      then connect ground wire and outlet box wire with wire connector (F) (if applicable).

11. Tighten green grounding screw (G). Do not over tighten.

12. Tuck wires inside outlet box (C).

 FIXTURE ASSEMBLY INSTRUCTIONS
 1.   Raise canopy (I) to ceiling allowing mounting screws (A) to protrude through key slots (J) in 

      canopy (I) (see fig. 1).

2.   Rotate canopy (I) clockwise until mounting screws (A) lock into narrow portion of key slots (J). 

      Secure into place with mounting screws (A).

3.   Install lamp(s). Do not exceed recommended wattage.

4.   Secure glass shade (K) into canopy (I) with thumb screws ( L ) .

5.   Turn power back on at circuit box.

W-393

071214

WARNING 
Turn off electricity to the mounting site before beginning installation.
Mounting instructions must be followed exactly as shown for the fixture to be safely sup-

ported.

CLEANING AND CARE 
To clean, wipe fixture with soft cloth.  Clean glass with mild soap.  Spray from chemical cleaners can 

discolor the finish of fixture.  Do not use scouring pads, powders, steel wool or abrasive paper to 

clean this fixture.
NOTE  FOR FIXTURES THAT ARE  SOLID BRASS:

Your hand-crafted, solid brass lighting fixture has been coated with a durable, baked-on acrylic lac-

quer which gives maximum protection against the weather.  However, in time the brightness of the 

brass will tarnish, giving way to an authentic old-world brass finish.  To keep your solid brass fixture 

looking new for years to come, regularly apply a good quality, non-abrasive car wax to all metal sur-

faces, giving the fixture an extra protective covering.

ORDERING PARTS 
Keep this manual for future reference, and in case replacement parts are needed.  Available parts can 

be ordered from place of purchase.  Use exact wording from diagrams when ordering parts.

 FIGURE 2.

GROUP A:

GROUP B:

CONNECT TO BLACK

HOUSE WIRE

BLACK

WHITE OR GREY WITH TRACER

BROWN, GOLD OR BLACK

WITHOUT TRACER

BROWN, GOLD OR BLACK WITH TRACER

WHITE

WHITE OR GREY WITHOUT TRACER

CONNECT TO WHITE

HOUSE WIRE

NOTE: When parallel wire (SPT 1 & SPT 2) is used; the neutral wire is square shaped

and ridged, and the hot wire will be round in shape and smooth. (See below.)

Westinghouse Lighting, Philadelphia, PA 19154-1029, U.S.A.  

www.westinghouselighting.com

       , WESTINGHOUSE, and INNOVATION YOU CAN BE SURE OF are trademarks of Westinghouse Electric Corporation.  
Used under licensee by Westinghouse Lighting. 

All rights reserved. 

 

Made in China        

   WARRANTY INFORMATION

This Westinghouse Lighting Fixture is warranted against defects in material and workmanship for a 

period of Five Years from purchase date.  This warranty is in lieu of all other warranties expressed or 

implied.
This warranty does not cover acts of nature such as lightning damage, or corrosion and discoloration 

of components, nor does it cover damages caused through abuse, improper installation, surges in 

electric current, or acts of third parties.
This warranty does not cover costs of removing and re-installing the lighting fixture.
If this product fails for any reason covered by this warranty, contact us toll free at 1-888-417-6222.

ASSEMBLY INSTRUCTIONS FOR OUTDOOR LIGHTING FIXTURE

Congratulations on your Westinghouse purchase.  This fixture has been designed to give you many 

years of beauty and service.  For questions and comments, please visit www.westinghouselighting.

com/contact-us.
NOTE: Carefully unpack fixture and parts.  Make sure all parts are included before discarding any pack-

ing materials (see figure 1).

 WARNING:   ELECTRICAL SHOCK CAN RESULT IN SERIOUS INJURY.

Read and follow instructions exactly as shown.  If instructions are unclear, do not proceed.  

Contact a qualified electrician.  Read all instructions before beginning.  Proper wiring is essen-

tial for safe operation of this fixture.  When cutting or drilling into walls or ceilings, do not dam-

age electrical wiring, gas lines, or water lines.  If any of the fixture or wiring components are 

damaged, do not install fixture.  Return to place of purchase.
For fixtures provided with 75° C or 90° C supply wire warning only. (These warnings are pro-

vided on the U.L. label and on the fixture carton.)  Risk of fire.  Most dwellings built before 1985 

have supply wires rated 60° C.  Consult a qualified electrician before installing.
NOTE: For fixture employing a grounded convenience outlet.  This fixture employs a grounded 

type receptacle and is not intended for connection to a two wire ungrounded source of supply.

Owner’s Manual

Outdoor Lighting Fixture  

Installation Instructions

Guide d’utilisation

Instructions d’installation

Appareil d’éclairage pour utilisation extérieure

GARANTIE LIMITÉE DE CINQ ANS
Cet appareil d’éclairage Westinghouse est assorti d’une garantie de 5 ans contre les défauts de matéri-

aux et de fabrication, qui entre en vigueur à partir de la date d’achat. La présente garantie se substitue 

à toute autre garantie expresse ou tacite.

 

Cette garantie ne porte ni sur les dommages survenant suite à une catastrophe naturelle (telle que la 

foudre), ni sur la corrosion ou la décoloration des pièces; la garantie ne porte pas sur les dommages 

survenant suite à une utilisation anormale, une installation impropre, une surtension de courant élec-

trique ou des actes d’un tiers.

 

Cette garantie ne porte pas sur les frais de démontage et de réinstallation du ventilateur.
Si ce produit ne fonctionne pas, pour une raison quelconque couverte par cette garantie, contactez- 

nous gratuitement au numéro suivant : 1-888-417-6222.

 MISE EN GARDE:  L’ÉLECTROCUTION POURRAIT CAUSER DE GRAVES BLESSURES PERSONNELLES.

Lisez ces instructions et suivez-les exactement comme illustré. En cas de doute, ne commencez 

pas l’installation. Consultez un électricien qualifié. Lisez toutes les instructions avant de com-

mencer l’installation. Un câblage approprié est essentiel au bon fonctionnement de cet appareil 

d’éclairage. Lorsque vous faites une entaille ou que vous percez un trou dans un mur ou un 

plafond, n’endommagez pas les câbles électriques, les canalisations de gaz ou d’eau. Si l’un des 

composants de raccordement ou de l’appareil d’éclairage est endommagé, n’installez pas cet 

appareil d’éclairage. Retournez-le à l’endroit où vous l’avez acheté.
Convient uniquement aux appareils comportant un avertissement indiquant que l’appareil 

d’éclairage est doté d’un fil supportant une chaleur de 75°C ou 90°C. (Ces avertissements se 

trouvent sur l’étiquette U.L. et sur l’emballage de l’appareil d’éclairage.)
NOTA: Pour appareil d’éclairage avec sortie terre. Cet appareil d’éclairage utilise un réceptacle 

muni d’un fil de terre et ne doit pas être branché à un bloc d’alimentation à deux fils non mis à 

la terre.

LES INSTRUCTIONS D’ASSEMBLAGE DE L’APPAREIL D’ÉCLAIRAGE POUR UTILISATION EXTÉRIEURE

Félicitations ! Vous avez acheté un produit de Westinghouse Lighting. Cet appareil d’éclairage a été 

conçu pour durer de nombreuses années. Si vous avez des questions ou des commentaires à

nous communiquer, veuillez visiter www.westinghouselighting.com/contact-us.
NOTA : Déballez soigneusement l’appareil d’éclairage et les pièces. Assurez-vous que toutes les pièces 

y sont avant de mettre l’emballage au rebut (voir fig. 1).

*NOT SUPPLIED

Line art shown may not exactly match the 

fixture enclosed. However, the installation 

instructions do apply to this fixture.

FIGURE 1.

GLASS

SHADE (K)

THUMB

SCREWS (L)

GREEN

GROUNDING

SCREW (G)

MOUNTING

BAR (B)

KEY SLOTS (J)

WIRE

CONNECTORS (F)

SIDE

HOLE (H)

CENTER

HOLE (E)

OUTLET BOX

SCREWS (D)

MOUNTING

SCREWS (A)

CANOPY (I)

*OUTLET

  BOX (C)

GROUND

WIRE

ABAT-JOUR

EN VERRE (K)

VIS A CLE (L)

VIS DE MISE

A LA TERRE

(VERTE) (G)

BARRE DE

FIXATION (B)

RAINURES (J)

CONNECTEURS

DE FIL (F)

TROU

LATERAL (H)

TROU

CENTRAL (E)

VIS DE LA BOITE DE

SORTIE DE COURANT (D)

VIS DE

FIXATION (A)

CHAPEAU (I)

*BOITE DE SORTIE

  DE COURANT (C)

FIL DE MISE

A LA TERRE

*NON FOURNI

Il est possible que le dessin illustré ici ne 

soit pas la reproduction exacte de l’appareil 

d’éclairage contenu dans la boîte.

Les instructions d’installation demeurent 

cependant valables.

FIGURE 1.

0.626056s