Troy-Bilt CSV206 User's Manual | Page 5
5
SECTION 2: ASSEMBLING YOUR CHIPPER SHREDDER VACUUM
Unpacking
•
Remove staples, break glue on top flaps, or cut
tape at carton end and peel along top flap to open
carton.
•
Remove loose parts if included with unit (i.e.,
operator’s manual, etc.)
•
Cut along corners, lay carton down flat, and remove
packing material.
•
Roll or slide unit out of carton and check carton
thoroughly for loose parts.
Loose Parts In Carton
Following is the list of loose parts shipped with your
equipment. Compare the parts with the illustration in
Figure 1 to identify these items.
1.
Nozzle
2.
Bag
3.
Chipper Chute
4.
Tamper Plug
5.
Oil (Not Shown)
Figure 1
Before Assembly
IMPORTANT:
This unit is shipped without gasoline or oil
in the engine. Be certain to service engine with gasoline
and oil as instructed in the accompanying engine
manual before operating your machine.
NOTE: Reference to right or left side of the equipment
is observed from the operating position, unless
otherwise stated.
•
Before starting assembly, disconnect the spark
plug wire from the spark plug on the chipper
shredder vacuum and ground against the engine.
Attaching The Nozzle
•
Remove three wing nuts from the front of the
chipper shredder vacuum.
•
Place nozzle in position over the three studs on unit
and secure with wing nuts just removed.
See Figure 2.
Figure 2
NOTE: The metal tab on the nozzle must depress the
safety switch button attached to the front of the chipper
shredder vacuum or the engine will not start.
Attaching the Chipper Chute
•
Loosen, but do not remove, the two hex bolts, flat
washers, and flange nuts which are secured to the
support bracket. See Figure 3.
Figure 3
•
Remove the two flange nuts, hex bolts and saddle
washers which secure the right side of the upper
handle to the right side of the lower handle.
See Figure 4.
Nozzle
Bag
Chipper Chute
Tamper Plug
Wing
Nuts
Wing
Nut
Nozzle
Chipper
Chute
Hex Bolts
Flat
Support
Bracket
Washers
Flange
Nuts
Also See for Troy-Bilt CSV206
Related Manuals for Troy-Bilt CSV206
-
Craftsman Chipper 486.24516 Operator's Manual
32 pages
-
Craftsman Chipper 247.795861 Operator's Manual
16 pages
-
Craftsman Chipper 247.77636 Operator's Manual
40 pages
-
GBC Chipper SHREDMASTER 1666S User's Manual
10 pages
-
Snapper Chipper LS5000 User's Manual
4 pages
-
Troy-Bilt Chipper CS 4310 User's Manual
1 pages
-
Troy-Bilt Chipper CSV 060 User's Manual
1 pages
-
Troy-Bilt Chipper 47330 User's Manual
27 pages
-
Echo Chipper Bear Cat CH922DH (74950) User's Manual
2 pages
-
Echo Chipper SC3305 (70080) User's Manual
2 pages
-
Echo Chipper SHRED'N'VAC ES-210 User's Manual
24 pages
-
MTD Chipper 242A645-000 User's Manual
12 pages
-
MTD Chipper 244-645B000 User's Manual
10 pages
-
Sears Chipper 247.79586 User's Manual
24 pages
-
Country Home Products Chipper C123E-CHP User's Manual
32 pages
-
EarthQuake Chipper 9060300 User's Manual
44 pages
-
Echo Bear Cat Chipper 70050 User's Manual
1 pages
-
Echo Bear Cat Chipper 70080 User's Manual
1 pages
-
Echo Bear Cat Chipper 70085 User's Manual
1 pages
-
Echo Bear Cat Chipper 70554 User's Manual
1 pages
-
Echo Bear Cat Chipper CH4614 (73420) User's Manual
2 pages
-
Echo Bear Cat Chipper CH611DH (76628) User's Manual
2 pages
-
Echo Bear Cat Chipper SC3206 User's Manual
1 pages
-
Echo Bear Cat Chipper SC3270T (70580) User's Manual
2 pages