Toshiba ASD-TB1-SIM9 Installation Manual
ASD-TB1-SIM9
Document Number 59707-000
ASD-TB1-SIM9 Installation Procedure
The ASD-TB1-SIM9 is used to demonstrate the many powerful features of the 9-Series ASDs and may be
used with any of the 9-Series ASDs.
The ASD-TB1-SIM9 was developed to emulate the input/output control signals of the 9-Series ASDs.
The simulated input signals of the ASD-TB1-SIM9 are provided via switches and pots.
The switches simulate discrete input signals, such as relays and contactors — the pots simulate analog
inputs, which may be voltage or current. The ASD-TB1-SIM9 uses LEDs to provide the status of the AM,
FM, OUT1, OUT2, and Fault signals.
The ASD-TB1-SIM9 connects to the Control Board and is installed using same slide-in method as the
Terminal Board that is normally used with the 9-Series ASD.
This procedure is to be performed by Qualified Personnel ONLY. See the Installation and
Operation Manual of the ASD being used for the complete description of the discrete and
analog operational applicables, and ASD safety precautions and requirements.
Ensure that the 3-phase input power to the ASD is off and that the circuit is properly
locked out and tagged out as per your local, regional, and/or state regulatory agency.
Failure to do so may result in equipment damage, injury, or death.
To prevent electrical shock, ensure that the front cover of the 9-Series ASD has been
secured before applying power to the unit.
Installation Procedure
1.
Open the front door of the 9-Series ASD and remove the lower front cover.
2.
Loosen the Torx® screw at the upper-right side of the Terminal Board.
3.
Remove the factory-installed Terminal Board from the 9-Series ASD.
4.
Insert the ASD-TB1-SIM9 into the 9-Series ASD. Ensure that the male S106 connector of the ASD-
TB1-SIM9 seats securely into the female connector of the 9-Series ASD Control Board.
5.
Secure the ASD-TB1-SIM9 using the Torx® screw in the upper-right side of the ASD-TB1-SIM9.
6.
The Torx® screw in the upper-right side of the ASD-
TB1-SIM9 does not require much torque to secure
the ASD-TB1-SIM9 into the 9-Series ASD. Once
the Torx® screw begins to resist turning, less than ½
of a turn is required to tighten securely.
7.
Replace the lower front cover and close the door of
the 9-Series ASD.
WARNING
Figure 1. ASD-TB1-SIM9 PCB.
Related Manuals for Toshiba ASD-TB1-SIM9
-
3Com Switch 2928 - Baseline Plus Switch PWR User's Manual
505 pages
-
Honeywell Switch RPLS740B User's Manual
8 pages
-
Honeywell Switch RPLS540A User's Manual
8 pages
-
HP Switch V1910 User's Manual
483 pages
-
Bontrager Switch 231793 Service Manual
30 pages
-
HP Switch 1920-16G Switch User's Manual
547 pages
-
HP Switch 1920-24G Switch Getting Started Guide
35 pages
-
HP Switch 1920-24G Switch User's Manual
547 pages
-
HP Switch 1920-24G-PoE+ (180W) Switch User's Manual
547 pages
-
HP Switch 1920-24G-PoE+ (370W) Switch User's Manual
547 pages
-
HP Switch 1920-48G Switch Getting Started Guide
35 pages
-
HP Switch 1920-48G Switch User's Manual
547 pages
-
HP Switch 1920-8G Switch User's Manual
547 pages
-
HP Switch 1920-8G-PoE+ (180W) Switch User's Manual
547 pages
-
TP-Link Switch TL-SF1008D User's Manual
4 pages
-
ZyXEL Switch 3000 Series User's Manual
8 pages
-
Netgear Switch Switch FS105 V2 User's Manual
4 pages
-
Delta Electronics Switch DTC1000 Series User's Manual
2 pages
-
M-Audio Switch KEYSTATION 49-KEY User's Manual
14 pages
-
Allied Telesis Switch AT 8624T/2M User's Manual
36 pages
-
RuggedCom Switch RSG2100 User's Manual
10 pages
-
RuggedCom Switch RS900 User's Manual
130 pages
-
HP Switch HP ProCurve 1410-24G Gigabit Ethernet Switch J9561A#ABA User's Manual
33 pages
-
HP Switch ProCurve 2626 (J4900A/B) User's Manual
306 pages