Thermo Products Thermo Pride Furnace L33-37-39 User's Manual
MO-200B
4569-MA
1
MODELS L33-37-39
FURNACE ASSEMBLY INSTRUCTIONS
This Thermo Pride furnace is shipped disassembled, however it was completely assembled at the factory first - then
disassembled for packaging. Holes were drilled into the various casing parts during assembly. If the furnace is
installed on a level surface and all parts put together properly, the holes will line up for metal screws. Do not redrill
any holes. Check for incorrect alignment of parts if holes do not line up.
Assemble furnace as follows: (Figs. 1, 2, and 3).
1. Set base pan on level floor where furnace is to be installed. (Fig. 1).
2. Set furnace heat exchanger (1) on base pan. Make certain heat exchanger is centered on base (side to side) and
pushed forward until the pouch front (2) of the heat exchanger is tight against base angle.
(See Fig. 1).
3. Assemble rear side casings to furnace (7). Set rear side casing on clip over base pan .
4. Install white crane glass gasket on flue flange of heat exchanger. (See Fig. 2).
5. Install rear separator (11) (See Fig. 1). Make certain angle on bottom of separator is engaged in base separator
clip. Rear separator must be installed over gasket on heat exchanger flue flange sandwiching the separator between
the heat exchanger flange and flue extensions flange. (See Fig. 2). Fasten to rear side casings with hex head sheet
metal screws in holes provided. (Rear flue models only).
6. Assemble flue pipe extension on flue flange of heat exchanger making certain the rear separator is installed
between the flue flanges. (See Fig. 2). No trim ring is provided for this location. Secure flanges securely using 5/16"
brass nuts provided.
7. Install front side casings (4) on base and lock into clip on base and join front and rear casing using the pocket
seam between casings, then fasten casings together with hex head sheet metal screws in holes provided. (See Fig. 1).
8. Insert lower front separator panel (3) around pouch in between base angle and pouch front , clip on lower front
separator panel (3). (See Figure 1.)
9. Fasten lower front separator panel (3) at bottom using #10x3/4" sheet metal screws. (See Fig. 1).
10. Install top front separator panel (6) and fasten to front side casings (4) with hex head sheet metal screws in the
holes provided. (See Fig. 1).
11. Install center front separator panel (5) aligning predrilled holes and fastening to the front side casings (4) with
hex head sheet metal screws. (See Fig. 1).
12. Install front bottom panel (8) on front of base between front side casings with hex head sheet metal screws in
holes provided. (See Fig. 1).
13. Carefully inspect combustion chamber to insure the chamber ears around upper perimeter of the fiber chamber
are inserted under the metal ears of the heat exchanger pouch.
14. Install upper (9) and lower (10) burner mounting plates with gaskets onto pouch front using 9/16" brass nuts.
(See Fig. 1).
Related Manuals for Thermo Products Thermo Pride Furnace L33-37-39
-
Bryant Furnace PLUS 90X 353AAV User's Manual
22 pages
-
Bryant Furnace 310AAV Service Manual
45 pages
-
Bryant Furnace 915SA Product data
16 pages
-
Bryant Furnace 350MAV User's Manual
12 pages
-
Bryant Furnace PLUS 95S 355CAV Owner's Manual
14 pages
-
Carrier Furnace WEATHERMAKER 8000 58ZAV Instruction Manual
24 pages
-
Coleman Furnace DGAA User's Manual
14 pages
-
Goodman Mfg Furnace GMS90453BXA Parts list
11 pages
-
Rheem Furnace CRITERION II Installation Manual
8 pages
-
Trane Furnace XR 90 SERIES Owner's Manual
16 pages
-
Carrier Furnace 58GS User's Manual
12 pages
-
Carrier Furnace 58MCB User's Manual
12 pages
-
Rinnai Furnace ENERGYSAVER ES38 User's Manual
44 pages
-
Bryant Furnace Condensing s 398AAV User's Manual
12 pages
-
Thermo Products Furnace Thermo Pride Furnace OL6RA072D48(B/R) User's Manual
75 pages
-
Thermo Products Furnace OL5-85 User's Manual
32 pages
-
Thermo Products Furnace Thermo Pride Furnace MHA1-75N User's Manual
61 pages
-
Atwood Mobile Products Furnace HYDRO FLAME 8940 User's Manual
7 pages
-
Westinghouse Furnace FG7TC 95.1% AFUE Two-Stage Technical Literature
8 pages
-
Maytag Furnace PGC2TC PGC2TL | Maytag M1200 95.1% AFUE Two-Stage Fixed-Speed Gas Furnace Technical Literature
8 pages
-
Rinnai Furnace EX22C (RHFE-559FTA) Installation and Operation Manual
84 pages
-
York Furnace TM9Y Technical Guide
4 pages
-
York Furnace TM9E User's Manual
8 pages
-
GAMA Furnace Gas-Fired Furnace User's Information Manual
40 pages