Spectra AL28M-2 User's Manual

Spectra Laser Level User's Manual - AL28M-2.
Download
Page  of 2
4.2, 1219 votes
background image

Features

01.  Focusing knob
02.  Sighting guide
03.  Crosshairs’ adjustment screws (under cover)
04.  Crosshairs’ focusing ring
05.  Eyepiece
06.  Horizontal rotation ring and angle index
07.  Leveling screws
08.  Base plate
09.  Circular level adjustment screws
10.  Horizontal tangent knob
11.  Circular level
12.  Mirror for reading circular level
13.  Objective

Maintenance and Care
• Aswithallprecisioninstruments,theautolevelshouldbe

transported and stored in its carrying case.

• Whencarryingtheinstrumentmountedtoatripod,besure

to carry it vertically rather than over your shoulder.

• Wheneverpossible,storetheinstrumentinadry,shadyarea.
• Wipetheinstrumentcleanwithacloth.Cleantheobjective

andeyepieceswithspecialcareusingadamptissueorsoft,

clean,lint-freecottoncloth.

• Whenworkinginwetweather,wipeofftheinstrumentand

carrying case in the field and let them dry completely indoors 

with the case open.

Safety Information
Included in this manual are Cautions and Notes. Each of  

thesewordsrepresentsalevelofdangerorconcern.ACaution 

indicates a hazard or unsafe practice that could result in 

minorinjuryorpropertydamage.ANoteindicatesimportant

information unrelated to safety.

Establishing an Elevation
1. Set up and level the instrument.
2. Set the grade rod on a known elevation (30.55 m) and take a 

grade rod reading (1.72 m).

3.Addthegraderodreadingtotheknownelevationtogetthe

height of instrument or HI (1.72 + 30.55 = 32.27 m).

4. Subtract the elevation of the point you want to establish 

(31.02 m) from the HI (32.27) to calculate the difference 

between the two points (32.27 – 31.02 =1.25 m).

5. Go to the point you want to establish and adjust the height of 

the grade rod until the calculated difference (1.25) is centered 

in the crosshairs.

Taking Measurements

Determining the Difference in Elevation

How to Use the Instrument

Setting Up the Instrument
1. Set up the tripod at a height appropriate for your use.
  Note: Make sure the tripod is stable and the tripod head is 

relatively level.

2.Attachtheinstrumenttothetripod.
3. Level the instrument using the circular level as a reference.
4. Focus the telescope crosshairs by turning the crosshairs’ 

focusing ring.

Aligning the Instrument
1.Alignthetelescopetothegraderodusingthesightingguides.
2. Turn the focusing knob to bring the grade rod into sharp 

focus. Precisely sight the center of the grade rod in the 

telescope crosshairs using the horizontal tangent knob.

3. Check for parallax shift.
  Note: No parallax exists if the crosshairs and the grade rod 

graduations remain in coincidence even when you change 

your viewing angle (move your eye up/down and left/right in 

front of the eyepiece).

  Note:Afterthebubbleinthecircularlevelhasbeencentered, 

thecompensatorcorrectsresidualline-of-sightinclinations.

Thecompensatordoesnot,however,eliminateanytilts

resulting from inadequate adjustment of the circular level or 

lineofsight.Thesemustbecheckedregularly(seeAdjusting

the Instrument for more information).

Taking a Distance Measurement
Note:

 The instrument’s stadia lines allow you to determine the 

distance between the instrument and the grade rod.
1. Take readings at the upper stadia  

line (1.436 m) and the lower stadia  

line (1.152 m).

2. Calculate the difference between  

the two readings (1.436 – 1.152 =  

0.284 m).

3. Multiply the difference by 100  

to get the distance between the  

instrument and the grade rod  

(.284 x 100 = 28.4).

Computation Example
Elevation
Center Line Reading 

1.294 m

Distance Measurement
Upper Stadia Line Reading 

1.436 m

Lower Stadia Line Reading 

1.152 m

Difference 

0.284 m

Distance (0.284 x 100) 

28. 4 m

– 2 –

– 3 –

– 4 –

– 

5 –

– 

6 –

– 7 –

– 8 –

7

5

4

8

13

12

10

11

9

3

6

2

1

1.Setuptheinstrumenthalfwaybetweentwopoints(AandB).
2.TakeareadingatpointA(a1 = 1.726 m) and another one at 

point B (b1 =1.259 m).

  Note:Aslightdeviationofthelineofsightfromhorizontal

will not cause any measuring error as long as the instrument  

is set up approximately half way between the two points.

3. Subtract b1 from a1 to get the difference between the points  

(d = 0.467 m).

  Note:PointBis0.467higherthanpointAbecausethe

difference is a positive number. If point B were lower than 

pointA,thenumberwouldbenegative.

15
14
13
12
11
10

AL 24/28/32 - A/M Series

Auto Levels

User Guide

www.trimble.com

a1

b1

A

B

1.259

1.726

0.467

0.622115s