Spectra 5.2XL User's Manual

Spectra Laser Level User's Manual - 5.2XL.
Download
Page  of 2
4.3, 1562 votes
background image

– 2 –

– 5 –

– 9 –

– 3 –

– 4 –

– 6 –

– 10 –

– 7 –

– 11 –

– 8 –

– 12 –

Applications
General Leveling and Aligning
1.  Place the laser on a flat surface.  The laser must be level within its self-

leveling range.

2.  Adjust the position of the Line or Point Beams so they are at the desired 

positions.

3.  Mark the position of the wall, elevation, floor or ceiling.
Installing and Plumbing a Wall

1.  Place the laser so the Vertical Line 

Beam is positioned over the desired 

wall location (usually indicated by 2 

floor marks).
NOTE:

 If the floor track is already 

installed the laser should be placed 

on the Universal Mount or 

Universal Mount Adapter so the 

Vertical Line can be positioned 

over the edge of the track. 

2.  Use the Vertical Line Beam to 

position the top track.

Batteries

Installation/Removal

CAUTION:

 The batteries should be removed when storing the laser more 

than 30 days.

1.  Release the battery door latch using your fingers, a coin, or a screwdriver. 

Open the door.

2.  Install/remove the AA batteries. Insert the positive (+) end first to ease 

installation.

  Note: When installing the batteries, be sure to note the positive (+) and 

negative (–) diagrams molded on the battery housing.

3.  Close the battery door and latch it shut.
Disposal
Some areas have regulations regarding the disposal of batteries. Be sure to 

dispose of discharged batteries properly.

5.2XL  

5-Point & CrossLine Laser

User Guide

www.trimble.com

ITF

ITF

2

4

Introduction
Thank you for choosing the Spectra Precision® Laser 5.2XL from the Trimble® 

family of precision products. This simple-to-use tool allows you to perform 

leveling or vertical plumb work. You can also use the laser outdoors for 

leveling and aligning applications (optional HR250 receiver required).
Before using the laser, be sure to read this operator’s manual carefully. 

Included in it is information about setting up, using, and maintaining the 

laser. Also included in this manual are CAUTIONS and Notes. Each of these 

words represents a level or danger or concern. A CAUTION indicates a hazard 

or unsafe practice that could result in minor injury or property damage. A 
Note

 indicates important information unrelated to safety.

Your comments and suggestions are welcome; please contact us at:
Trimble Construction Tools Division 

8261 State Route 235 

Dayton, Ohio 45424 U.S.A. 

Phone:  (937) 245-5600 

 

(800) 538-7800 

FAX: 

(937) 233-9004 

Internet:  www.trimble.com/spectra

6.  Laser Line Exit Windows - 

Horizontal and Vertical

7.  Protective Rubber Bumper

8.  Compensator Lock / 

Manual Mode Switch

 0002-3420 Universal Mount

Features

1

3

5

1.  Power / Mode button 

2.  Manual Mode / Compensator 

Lock On LED

3.  Power On / Low Battery LED

4.  Receiver Mode On LED

5.  Receiver Mode Button

6

7

8

9

9.  Laser Pointer Exit Windows (5) 

Left, Right, Up, Down, Front

10.  5/8x11 Thread and  

1/4x20 Thread

11.  Battery Door

10

11

HR250 Receiver
1.  Power and Audio Button – turns 

the receiver on/off and changes the 

audio to loud, soft, and off.

2.  Marking Notches (both sides) – 

align with the on-grade portion of 

the photocell and are used to mark 

elevation readings. The marking 

notches are 50 mm (2 in.) from the 

top of the receiver.

3.  Grade-Sensitivity Button— allows 

you to select the receiver’s on-grade 

sensitivities, which include fine: 1.5 mm 

(1/16 in.) and medium: 3 mm  

 (1/8 in.).

4.  LEDs – show the position of the 

receiver relative to the laser beam (above 

grade, on grade, or below grade).

5.  Front and Back Liquid Crystal Displays 

(LCDs)

 – show the power, audio, elevation, 

grade sensitivity and battery status.

6.  Photocell – detects the laser beam when 

it strikes the receiver. If the photocell 

does not detect the laser beam for 30 

minutes, the receiver shuts off 

automatically.

2

2

5

1

3

6

7

4

HR250 Receiver (cont.)
7.  Audio Port – is the opening the sound comes out of.
8.  Clamp-Tab Recess – is the area that the general-purpose clamp’s release 

tab fits into.

9.  Label – shows the serial number and manufacturing date.
10.  Battery Housing – holds 2 AA alkaline batteries.
11.  Battery Door – holds the batteries securely 

8

9

10

11

General-Purpose Clamp
The C59 clamp allows the receiver to be attached to a survey rod or wooden pole.
1.  Release Tab – allows the receiver to be locked onto or released from the 

general-purpose clamp.

2.  Jaws – close/open so that the general-purpose clamp can be attached to or 

released from a survey rod or 

wooden pole.

3.  Jaws Screw – controls the closing/

opening of the jaws.

4.  Reading Edge – aligns with the 

receiver’s on-grade marking 

notches.

5.  Bubble Screw Holes – are where 

the optional 1277-6251S rod 

bubble kit is mounted.

1

3

2

5

4

Basic Operation

1.  Unlock the laser’s compensator by sliding the switch to the LEFT. 
NOTE:

 For added mechanism protection always lock the laser when not in 

use by sliding the switch to the RIGHT.

2.  Press the POWER button, the POWER LED illuminates GREEN. To 

turn OFF the laser, PRESS & HOLD the POWER button for 3 seconds.

3.  Each time the POWER button is pressed the laser beams will cycle through 

the following sequence: H LineV LineHV Lines5 PointsAll Beams

4.  When the unit is tilted out of its self-leveling range the laser beams will 

blink 2 times per second.

5.  The laser can be taken out of automatic self-leveling mode to perform 

slope work by locking the laser’s compensator (slide the switch to the 

RIGHT). In this mode the LOCK symbol LED will illuminate GREEN, 

and the laser beams will flash 3 times every 30 seconds.

6.  To operate the laser with the HR250 receiver press the RECEIVER 

button.  The RECEIVER LED will illuminate GREEN.

7.  When the batteries need changed the POWER LED illuminates RED.
8.  To turn OFF the laser, PRESS & HOLD the POWER button for 3 seconds.

Installing a Ceiling
1.  Measure up from the floor (or other reference 

mark) to the finished ceiling height.

2.  Install the first piece of wall molding.
3.  Slide the ceiling plate (0002-3480) behind 

the wall molding.

4.  Attach the Universal Mount (0002-3420) 

and Universal Mount Adapter (0002-3430) 

to the laser and magnetically attach it to 

the ceiling plate so that the level beam is at 

wall molding height. Install the rest of the 

wall molding.

5.  Lower the laser 5 cm (2.0 in.) on the 

ceiling plate so that the level beam is at the 

horizontal target elevation.

6.  Install the ceiling’s cross Ts and main Ts.

3.  Use the Vertical Line Beam to position the floor track.
4.  To locate the plumb point over a wall corner or other point place the 

Down Point Beam over the corner or mark.  Use the Up Point to 

determine the top track corner location.

NOTE: If the floor track is already installed use the Universal Mount to 

position the Down Point over the corner. Add the Universal Mount 

Adapter if tall floor track is being used.

Over Tall Floor Track or Obstacles with 

0002-3430 Universal Mount Adapter

Ceiling with 0002-3430 Universal Mount 

Adapter and 0002-3480 Ceiling Plate

Columns with Mounting Strap

Pipes / Conduit with  

Mounting Strap 

1 M (4 Ft) Marks

Universal Mount & Adapter

12. Nail Mounting Hole

13. Magnets

14. Fine Adjustment Knobs

15. Slots for Mounting Straps 

16.  5/8x11 Thread and  

1/4x20 Thread

17. 1/4x20 Mounting Knob - 

Sliding

18. Universal Mount Adapter - 

Mounts on Top for 360º Swivel 

or on Bottom to raise above 

obstructions or tall track

19. 5/8x11 Thread

20. 1/4x20 Thread

12

13

14

15

18

17

16

5.2XL

20

19

5.2XL

0.606993s