Sony BDV-IT1000ES User's Manual
BDV-IT1000ES 4-109-711-11(1)
-
4-109-711-11(1)
©2008 Sony Corporation Printed in Malaysia
BDV-IT1000ES
(1)
Basic connections
These instructions are for basic connections.
For more information, see the Operating
Instructions.
English
Supplieditemsforassembling
thespeakers
Front left speaker (L) (1, white label)
Front right speaker (R) (1, red label)
Surround left speaker (L) (1, blue label)
Surround right speaker (R) (1, gray label)
Center speaker (1, green label)
Desktop stands (4)
Baffle covers (short) (3)
Baffle covers (long) (2)
Gril s (5)
Speaker cords (5, white/red/blue/gray/green)
Foot pads (for center speaker) (Thick) (2)
Foot pads (for center speaker) (Thin) (2)
Note
Unpack the speakers, being careful not to touch the
speaker units.
Keep speakers away from one another. Speakers are
magnetical y attracted, may hit each other, and cause
damage.
Keep magnetic objects such as watches, magnetic
card, etc., away from the speakers.
Notesonusingthespeakers
When moving the speakers, keep one hand under
the desktop stand and hold both sides of the speaker
().
When using the speakers, avoid the following. These
actions may damage the speaker.
Toppling the speaker.
Shaking the speaker.
Swinging the speaker.
Pushing on the speaker.
Hitting the speaker.
Spread a cloth on the floor to avoid damaging the
floor when you assemble the speakers.
When assembling, take care not to touch the speaker
unit ().
Be sure to use the speakers with their grilles
attached.
Do not push on a grille that is attached, as it may
cause damage to the speaker unit.
Assemblingthespeakers
Before connecting the speakers, assemble the
speakers.
Assemblingfrontandsurround
speakers
1 Threadthespeakercord()throughthe
holeonthebottomofthedesktopstand().
2 Removethescrewfromthespeaker(, ,
, ).
The removed screw is used when attaching the
desktop stand. Be sure not to lose the screw.
3 Connectthespeakercords() tothespeaker
(, , , ).
The connector and color tube of the speaker cords
are the same color as the label of the jacks to be
connected.
Use the speaker cords as follows:
Front left speaker (L): White
Front right speaker (R): Red
Surround left speaker (L): Blue
Surround right speaker (R): Gray
Be sure to match the speaker cords to the
appropriate terminals on the speakers: the speaker
cord with the color tube to , and the speaker
cord without the color tube to . Do not catch
the speaker cord insulation in the speaker
terminals.
Insert the speaker cords into the speaker terminal
of the speaker as far as they will go. Ensure that
the cords are secure by gently pulling on them one
at a time.
Tip
When removing the speaker cord from the
speaker terminal, pull out the speaker cord while
pressing the white button on the speaker terminal
with a tool such as a flathead screwdriver.
4 Attachthespeaker(, , , )tothe
desktopstand().
Be careful with the orientation of the desktop
stand and speaker. Secure the speaker with the
screw removed in Step 2.
Tip
The curved edge of the stand and the slot on the
bottom of the desktop stand should face to the
rear.
5 Takeupslackinthespeakercord() by
pullingfromthebottomofthedesktopstand
() andsecurethespeakercordbyrunning
itthroughtheslot.
6 Attachthebafflecover(, ) tothespeaker
(, , , ).
Use the baffle cover (short) for the front speaker,
baffle cover (long) for the surround speaker.
7 Attachthegrille() tothespeaker(, ,
, ).
Be careful with the orientation of the grille. The
“SONY” logo should be at the bottom of the grille.
AssemblingCenterspeaker
1 Removethecoverfromthespeaker().
Pry up the cover by inserting a thin, flat object
into the slit in the cover. To replace the cover, see
Step 3. Be sure not to lose the cover.
2 Connectthespeakercords()tothespeaker
().
Use the speaker cords (green). Be sure to match
the speaker cords to the appropriate terminals on
the speakers: the speaker cord with the color tube
to , and the speaker cord without the color tube
to . Do not catch the speaker cord insulation in
the speaker terminals.
3 Securethespeakercord() byrunningit
throughtheslot,thenattachthecovertothe
speaker().
4 Attachthebafflecover(short)() tothe
speaker().
Use the baffle cover (short).
5 Attachthegrille() tothespeaker().
Be careful with the orientation of the grille. The
“SONY” logo should be at the left side of the
grille.
6 Attachthefootpads(thick(),thin())to
thebottomofthespeaker().
Attach the foot pads (thick) () to the front of
the speaker, and the foot pads (thin) () to the
rear so that the speaker tilts up when installed on
a TV stand, etc.
-
Français
Elémentsfournispour
l’assemblagedesenceintes
Enceinte avant gauche (L) (1, étiquette
blanche)
Enceinte avant droite (R) (1, étiquette
rouge)
Enceinte gauche surround (L) (1, étiquette
bleue)
Enceinte droite surround (R) (1, étiquette
grise)
Enceinte centrale (1, étiquette verte)
Socles de bureau (4)
Caches d’enceinte (courts) (3)
Caches d’enceinte (longs) (2)
Grilles (5)
Cordons d’enceinte (5, blanc/rouge/bleu/
gris/vert)
Tampons (pour l’enceinte centrale) (épais)
(2)
Tampons (pour l’enceinte centrale) (fins) (2)
Remarque
Déballez les enceintes en veil ant à ne pas toucher les
haut-parleurs.
Eloignez les enceintes les unes des autres. En effet,
elles subissent une attirance magnétique et risquent
de se heurter, provoquant ainsi des dégâts.
Eloignez les objets magnétiques, tels que les montres,
les cartes magnétiques, etc., des enceintes.
Remarquessurl’utilisationdes
enceintes
Lorsque vous déplacez les enceintes, laissez une
main sous le socle de bureau et maintenez-la de part
et d’autre ().
Lorsque vous utilisez les enceintes, évitez d’effectuer
les actions suivantes. Sinon, vous risquez de les
endommager.
Renverser l’enceinte.
Secouer l’enceinte.
Faire pivoter l’enceinte.
Appuyer sur l’enceinte.
Heurter l’enceinte.
Recouvrez le sol d’un linge pour éviter de
l’endommager lors de l’assemblage des enceintes.
Lors de l’assemblage, veillez à ne pas toucher le haut-
parleur ().
Veillez à utiliser les enceintes avec les grilles fixées.
N’appuyez pas sur une grille fixée, car vous
risqueriez d’endommager le haut-parleur.
Assemblagedesenceintes
Avant de raccorder les enceintes, assemblez-les.
Assemblagedesenceintesavantet
surround
1 Faitespasserlecordond’enceinte()à
traversl’orificesituésurledessousdusocle
debureau().
2 Retirezlavisdel’enceinte(, , , ).
La vis retirée sert à fixer le socle de bureau. Veillez
à ne pas perdre la vis.
3 Raccordezlescordonsd’enceinte()à
l’enceinte(, , , ).
Le connecteur et le tube coloré des cordons
d’enceinte sont de la même couleur que l’étiquette
des prises à raccorder.
Utilisez les cordons d’enceinte comme suit :
Enceinte avant gauche (L) : Blanc
Enceinte avant droite (R) : Rouge
Enceinte gauche surround (L) : Bleu
Enceinte droite surround (R) : Gris
Veillez à faire correspondre les cordons d’enceinte
aux bornes appropriées des enceintes : le cordon
d’enceinte doté du tube coloré correspond à et
le cordon d’enceinte dépourvu de tube coloré
correspond à . Ne coincez pas l’isolant du
cordon d’enceinte dans les bornes d’enceinte.
Insérez à fond les cordons d’enceinte dans la borne
d’enceinte de l’enceinte. Vérifiez que les cordons
sont correctement fixés en tirant délicatement sur
chacun.
Conseil
Lorsque vous retirez le cordon d’enceinte de la
borne d’enceinte, extrayez-le en appuyant sur le
bouton blanc situé sur la borne d’enceinte avec un
outil, tel qu’un tournevis à tête plate.
4 Fixezl’enceinte(, , , )ausoclede
bureau().
Soyez attentif à l’orientation du socle de bureau et
de l’enceinte. Fixez l’enceinte à l’aide de la vis
retirée à l’étape 2.
Conseil
Le bord recourbé du socle et la fente située sur le
dessous du socle de bureau doivent être orientés
vers l’arrière.
5 Tendezlecordond’enceinte()enletirant
depuisledessousdusocledebureau()et
fixezlecordond’enceinteenleplaçantdans
lafente.
6 Fixezlecached’enceinte(, )àl’enceinte
(, , , ).
Utilisez le cache d’enceinte (court) de l’enceinte
avant et le cache d’enceinte (long) de l’enceinte
surround.
7 Fixezlagrille()àl’enceinte(, , , ).
Soyez attentif à l’orientation de la grille. Le logo
« SONY » doit se trouver sur le dessous de la
grille.
Assemblagedel’enceintecentrale
1 Retirezlecouvercledel’enceinte().
Retirez le couvercle en insérant un objet fin et plat
dans la fente de celui-ci. Pour remettre le
couvercle en place, reportez-vous à l’étape 3.
Veillez à ne pas perdre le couvercle.
2 Raccordezlescordonsd’enceinte()à
l’enceinte().
Utilisez les cordons d’enceinte (verts). Veillez à
faire correspondre les cordons d’enceinte aux
bornes appropriées des enceintes : le cordon
d’enceinte doté du tube coloré correspond à et
le cordon d’enceinte dépourvu de tube coloré
correspond à . Ne coincez pas l’isolant du
cordon d’enceinte dans les bornes d’enceinte.
3 Fixezlecordond’enceinte()enleplaçant
danslafente,puisfixezlecouvercleà
l’enceinte().
4 Raccordezlecached’enceinte(court)()à
l’enceinte().
Utilisez le cache d’enceinte (court).
5 Fixezlagrille()àl’enceinte().
Soyez attentif à l’orientation de la grille. Le logo
« SONY » doit se trouver du côté gauche de la
grille.
6 Fixezlestampons(épais(),fins())surle
dessousdel’enceinte().
Fixez les tampons (épais) () à l’avant de
l’enceinte et les tampons (fins) () à l’arrière afin
que l’enceinte soit inclinée vers le haut lors de son
instal ation sur un meuble TV, etc.
Check the polarity on the label and its color.
Vérifiez la polarité indiquée sur l’étiquette et sa couleur.
Connector
Connecteur
Color tube
Tube coloré
3
Bottom of the desktop stand
Dessous du socle de bureau
1
Screw
Vis
2
7
5
Adjust the length of the cord.
Réglez la longueur du cordon.
Screw
Vis
4
Cover
Couvercle
Slit
Fente
1
Slot
Fente
Cover
Couvercle
3
5
4
Fully-assembledillustration
Illustrationdel’assemblagecomplet
6
“” mark
Repère « »
White
Blanc
Red
Rouge
Blue
Bleu
Gray
Gris
Green
Vert
Fully-assembledillustration
Illustrationdel’assemblagecomplet
Ex. Front speaker
Ex. : Enceinte avant
Speaker unit
Haut-parleur
6
Color tube (green)
Tube coloré (vert)
Connector (green)
Connecteur (vert)
2
Check the polarity on the label and its color.
Vérifiez la polarité indiquée sur l’étiquette et sa couleur.
Slot
Fente
Bottom of the desktop stand
Dessous du socle de bureau
Raccordements de base
Ces instructions concernent les raccordements de
base.
Pour obtenir davantage d’informations, consultez le
Mode d’emploi.
Related Manuals for Sony BDV-IT1000ES
-
GE Stereo System Spacemaker 7-5400 User's Manual
12 pages
-
Zeck Audio Stereo System PT-series Owner's Manual
30 pages
-
Zeck Audio Stereo System PT9 Service Manual
27 pages
-
Yamaha Stereo System RX-V2500 Owner's Manual
107 pages
-
Yamaha Stereo System RX-V650 Owner's Manual
90 pages
-
Yamaha Stereo System RX-V657 Owner's Manual
98 pages
-
Yamaha Stereo System RX-V793 Owner's Manual
59 pages
-
Yamaha Stereo System RX-V1400 Owner's Manual
90 pages
-
Yamaha Stereo System RX-V490 Owner's Manual
31 pages
-
Yamaha Stereo System DSP-A3090 Operation Manual
74 pages
-
Yamaha Stereo System RX-V420 Owner's Manual
69 pages
-
Yamaha Stereo System RX-V1600 Owner's Manual
123 pages
-
Denon Stereo System AVC - A 1 D User's Manual
2 pages
-
Denon Stereo System AVR 1610 User's Manual
2 pages
-
Denon Stereo System AVR-3802 User's Manual
74 pages
-
ProScan Stereo System PSP288-PL User's Manual
18 pages
-
Pioneer Stereo System VSX-D906S User's Manual
84 pages
-
Polk Audio Stereo System RM6750 User's Manual
16 pages
-
Technics Stereo System SC-CH900 User's Manual
79 pages
-
Nakamichi Stereo System Nakamichi Stereo System SoundSpace 5 User's Manual
36 pages
-
Boss Audio Systems Stereo System BV9967B User's Manual
10 pages
-
NAD Stereo System 402 User's Manual
2 pages
-
Midas Stereo System PRO2 Owner's Manual
582 pages
-
Bose Stereo System Solo 5 Owner's Manual
34 pages