Sanyo Welder MCO-19M(UVH) User's Manual | Page 6
5
Do not use the unit outdoors.
Current leakage or electric shock may result if the unit is exposed to
rain water.
Only qualified engineers or service personnel should install the unit.
The installation by
unqualified personnel may cause electric shock or fire.
Install the unit on a sturdy floor and take an adequate precaution to prevent the unit from
turning over.
If the floor is not strong enough or the installation site is not adequate, this may result
in injury from the unit falling or tipping over.
Never install the unit in a humid place or a place where it is likely to be splashed by water.
Deterioration of the insulation may result which could cause current leakage or electric shock.
Never install the unit in a flammable or volatile location.
This may cause explosion or fire.
Never install the unit where acid or corrosive gases are present
as current leakage or electric
shock may result due to corrosion.
Always ground (earth) the unit to prevent electric shock.
If the power supply outlet is not
grounded, it will be necessary to install a ground by qualified engineers.
Never ground the unit through a gas pipe, water main, telephone line or lightning rod.
Such
grounding may cause electric shock in the case of an incomplete circuit.
Connect the unit to a power source as indicated on the rating label attached to the unit.
Use
of any other voltage or frequency other than that on the rating label may cause fire or electric shock.
Never store volatile or flammable substances
in this unit if the container cannot be sealed. These
may cause explosion or fire.
Do not insert metal objects such as a pin or a wire into any vent, gap or any outlet
on the unit.
This may cause electric shock or injury by accidental contact with moving parts.
Use this unit in safe area when treating the poison, harmful or radiate articles.
Improper use
may cause bad effect on your health or environment.
Turn off the power switch (if provided) and disconnect the power supply to the unit prior to any
repair or maintenance
of the unit in order to prevent electric shock or injury.
Do not touch any electrical parts (such as power supply plug) or operate switches with a wet
hand.
This may cause electric shock.
WARNING
Related Manuals for Sanyo Welder MCO-19M(UVH)
-
Lincoln welder MIG 140C User's Manual
1 pages
-
Lincoln welder MIG 180C User's Manual
1 pages
-
Lincoln welder SP-135T User's Manual
1 pages
-
Chicago Electric welder 40388 User's Manual
17 pages
-
Chicago Electric welder MIG 170 User's Manual
32 pages
-
Chicago Electric welder 95136 User's Manual
24 pages
-
Campbell Hausfeld welder WIRE FEED WF2000 User's Manual
40 pages
-
Miller Electric welder 602 User's Manual
40 pages
-
Miller Electric welder Auto-Axcess 450 User's Manual
68 pages
-
Miller Electric welder Maxstar 200 STR User's Manual
56 pages
-
Miller Electric welder R-115 User's Manual
36 pages
-
Miller Electric welder S-22P12 User's Manual
28 pages
-
Miller Electric welder SRH-444 User's Manual
2 pages
-
Miller Electric welder SSW-2020 ATT User's Manual
4 pages
-
Miller Electric welder Thunderbolt XL AC/DC User's Manual
2 pages
-
Miller Electric welder XMT 350 CC/CV User's Manual
40 pages
-
Miller Electric welder XMT 400 User's Manual
36 pages
-
Miller Electric welder XMT 456 CC User's Manual
44 pages
-
Miller Electric welder XR Control User's Manual
72 pages
-
Tektronix welder Welder 2467B User's Manual
194 pages
-
Lincoln Electric welder AC-225 User's Manual
2 pages
-
Lincoln Electric welder NA-3N User's Manual
8 pages
-
Lincoln Electric welder RANGER 250 GXT User's Manual
36 pages
-
Miller Electric welder XMT 304 CC/CV Owner's Manual
40 pages