Sanyo Washer ASW-A85HT User's Manual | Page 8

Sanyo Washers User's Manual - Washer ASW-A85HT.
Download
Page  of 8
4.5, 2102 votes
background image

13

1

14

1

TROUBLE SHOOTING GUIDE

When the following problems occur, the microcomputer will detect the abnormal condition 
and an electronic buzzer sounds for approximately 10 seconds and digital display 
indicates flash as shown below.

NOTE: The Trouble indicators can be released by pressing the START/PAUSE button 
once if you want to release the emergency stop. Then press the START/PAUSE button 
again to restart the operation.

1.During Washing or Rinsing, still there is Water inletting. This is possibly automatic water 
   adding due to water level decrease. 
2.Spin tub turns or stops timely at the beginning of spinning. This is intermittent spinning 
   for better spin effect.
3.No drainage during overflow rinse. This is caused by lower water level set or lower water 
   pressure. 
4.Water inletting and rinsing sometimes during spinning. This is automatic lean-correction 
   due to clothe is not equally inside. 
5.There is sound like water flow after spinning. This is the sound of balance liquid in 
   Balance ring. It is for reducing vibration of spinning. 
6.Control panel keeps warm after Power Off, this is caused by Remember circuitry 
   working.
7.Power off during working and the washer could not continue working. Should set the 
   program again. 

VARIOUS FUNCTIONS

V

NO TROUBLE CONDITIONS

NO 

OTHERS

Kind of Trouble

The washer 
does not work 
at all






 Check the POWER ON/OFF button.
 Check the START/PAUSE button. 
 Check whether under PRESET condition.
 Check the power cord whether is securely plugged in. 
 Check whether power failure occurs.
 Check whether the fuse or circuit breaker has been 

   activated. 





 Turn on the water supply faucet.
 Check whether water supply has been cut off.
 Check whether the metal filter in water inlet is clogged. 
 Check whether washer has been freezing.
 Check whether water pressure is too low. 



 Check whether the Drain Hose has been put down. 
 Check whether the drain hose rises too high.
 Check whether the drain hose is clogged. 


 Check whether the laundry is clumped on one side of tub. 
 Check whether the washer is on the level surface. 

● Close the washer lid.


 Check whether the washer is under Child Lock. 
 Close the washer lid.

Press the POWER ON/OFF button, call the local 
service-person or dealer.

Water does 
not flow into 
tub or water 
flow is slim 

Water does 
not drain out

The washer
 does not spin

Does not wash

Other troubles

Trouble 
Indication

Where to Check

Water Inlet

Filter

Clean the water inlet valve
(Suggest clean it every 6 months) 
After long time use, The water inlet mesh 
bag may be blocked with crud, 
please load off the water inlet hose, 
take out the water inlet mesh bag 
from the water inlet valve, clean 
the mesh bag, then assemble 
the mesh bag in the valve and
 load the water inlet hose.

Clean lint filter  
(Suggest clean it every week)
1. Take out the lint filter
2. Pull out the scraps and wash 
    the lint filter in the water.
3. Install the Filter. 
    aim the frame claw to the 
    groove below.
( Lint Filer is easily destroyed parts).

Clean washing machine
Use soft clothing to wipe off the water or 
dirt on the surface of the washer.
● Do not spray water directly 
   to the washer body. 
● Detergent, propellant and 
   other chemicals are not 
   allowed to use to avoid the 
   damages on the surface.

Clean “ magic ” hose joint filter 
(Suggest clean it every 6 months)
1. Pull the water inlet hose out. 
2. Turn off the revolver according to
    below figure.
3. Load off the “ Magic ” Hose Joint 
    filter and clean the crud with a 
    toothbrush.
4. Install the clean “ Magic ” Hose Joint 
    filter to revolver and water inlet hose.

CARE AND MAINTENANCE

CARE 

 
1.Delete the end buzzer: Press POWER ON/OFF button to switch on the power, and press 
   START/PAUSE button for 4 seconds till a sound from buzzer. To restore it, repeat above 
   or pull out the plug.
2.How to drain remaining water
   When select this function, in 9 minutes after the working finished, the drainage valve will 
   open to drain out the remained water inside. This will avoid water freezing inside in winter 
   when temperature below 0℃. 
● Method of Use
   Press POWER ON/OFF  button to switch on the power, and press PROCESS button for 
   4 seconds till a sound from buzzer. To restore it, repeat above or pull out the plug.

0.499236s