Sanyo HEC-DR7700C User's Manual | Page 8

Sanyo Automobile Accessories User's Manual - HEC-DR7700C.
Download
Page  of 16
4.8, 2430 votes
background image

14

13

ADJUSTMENT OF CHAIR

Before sitting on the massage chair

OR

(Remote control) (Sensor control er)

Raise the back rest, and 

lower the foot rest by 

continuously pressing 

the UP (     ) button.

Recline the back rest, and 

raise the foot rest by 

continuously pressing 

the DOWN (     ) button.

Do not attempt to recline the back rest deeply at first (until the body is accustomed to massaging), 

so that the massage force may be too strong.

Be sure to check that there is no-one or any pets around the massager prior to adjusting the back 

rest. It may result in an accident or injury.

While massaging the legs, do not attempt to recline the back rest when the legs are squeezed by 

the air bags. Do not pull the legs out forcibly, this may result in injury to the legs.

NOTE

Head cover

5 Adjust the angle of the back rest.

The back rest and foot rest are moved in conjunction with each other.

Adjustment range 

Approx. 50

°

120

Adjustment range Approx. 90

°

Back rest

Foot rest

1 Sit on the center of massage chair.

Center of the chair

Foot rest

2 Adjust the position of head cover.

4 Press ZERO-G button to move the back rest, 

foot rest, and the seat to achieve the desired 

reclining position.

ZERO-G 1 (Zero gravity position 1)
Posture suited for whole body massaging

ZERO-G 2 (Zero gravity position 2)
Posture suited for lower body massaging

ZERO-G 1

(Slow flickering) 

ZERO-G 2

(Rapid flickering)

Back rest

Foot rest

Hook-and-

loop fasteners

When the button is pressed, the lamp of the remote control 

illuminates and the sole warmer will turn on. 

When the foot rest is fully lowered, the foot rest will rise a little.

When the massaging rollers are not located in the upper section, 

the massaging rollers will move to the upper section and stop. 

(During the movement, the characters of "ORIGIN" on the remote 

control flicker.) 

3 Press the OPERATION ON/OFF button.

Press

Press

Adjust the attaching position with 

hook-and-loop fasteners.

During the massage, adjust the head 

cover not to touch the shoulders.

Do not attempt to climb onto or off the seat 

by stepping on the foot rest. Do not attempt 

to place anything upon or sit on the foot rest. The 

user may fall over, resulting in an accident 

or injury.

NOTE

For safety, check the position of the 

massaging rollers before leaning slowly 

back on the massager. Do not twist the 

body, but lean straight back on the 

massager, so that the massaging rollers 

are in position on either side of the spine.

CAUTION

Sit deeply in the massage chair so that the 

waist touches the back rest. 

Bring all parts of the massage chair to 

their home position by pressing the 

HOME POSITION button.

Sitting on the massage chair while the foot rest is being raised 

is dangerous. Be sure to lower the foot rest completely before 

sitting on the massage chair.

The chair will be automatically brought to its home position by 

pressing the HOME POSITION button.

Reclining positions change automatically at each press of the button. 

(Button illuminates while reclining and flickers when in position)

Keep the RECLINING button pressed until the desired angle is achieved.

When adjusted at ZERO-G, the seat is lowered together with the above mentioned movement. 

(It is not possible to adjust only the seat.)

For the sake of safety, if the UP (▲) button is pressed with the seat raised, the foot rest may be raised 

briefly before going down.

*Automatically starts massaging in Air 

Course (Massaging besides Air Course 

cannot be selected)

When switched from ZERO-G 1 to 2, the foot rest is raised first, and moves to the set angle.

When switched form ZERO-G 2 to 1, the back rest is raised first, and moves to the set angle.

Reclining can be stopped during the reclining motion by pressing either the ZERO-G button, HOME POSITION 

button, RECLINING button, FOOT REST button, OPERATION ON/OFF button, or STOP button. 

When the reclining motion is stopped by pressing the STOP button, press the OPERATION ON/OFF button to 

resume the operation. 

When the reclining motion is stopped by pressing buttons other than the STOP button, press he desired button 

for motion. 

When back rest angle is adjusted from the ZERO-G 2, massaging other than Air Course can be selected.

Related Manuals for Sanyo HEC-DR7700C

0.506822s