Sanyo DC-MX41i User's Manual | Page 10

Sanyo Stereo System User's Manual - DC-MX41i.
Download
Page  of 21
4.2, 2212 votes
background image

8

OPERATING THE UNIT

Before operating the unit for the first time, make sure the AC power cord is properly connected to a 240V 50Hz 
AC outlet, then press the power ON switch on the rear of the unit, the unit will be in standby mode, the backlight of 
standby is red. You can now press the STANDBY/ON button on the unit or press the STANDBY/ON button on remote 
control to switch the unit ON. The backlight of the standby will be off and multi function touch plate will light on blue. 
Pull the AC plug out of the wall socket if you want to switch off completely. 

STANDBY/ON

1. Press the STANDBY/ON button on the unit or remote control to switch the unit on.
2. Select the sound source (CD, USB, CARD, iPod, AUX or TUNER) by touching the FUNC on the unit or press the 
    FUNCTION 

button on remote control. The corresponding display will light up.

3. Adjust the volume with the VOL      or VOL      on the unit or remote control.
4. Press the STANDBY/ON button on the unit or remote control again to turn off the unit.
Note: 1. During in standby mode, press any button/key can make the display light for 10 seconds.
          2. Please turn the main switch off to save energy, when you do not use the unit.

During in the STANDBY mode.
1. Press and hold the iPod/MEM/C-ADJ. button until the time displays will change to 24-hour format and flash.
2. Touch        or        on the unit or press        or        button on the remote control to select 12-hour or 24-hour. 
3. Press the iPod/MEM/C-ADJ. button again, the HOUR digit will flash on the display, touch        or        to adjust
    HOUR. 
4. Press the iPod/MEM/C-ADJ. button once more, the MINUTE digit will flash on the display, touch        or       
    to adjust minute.
5. Press the iPod/MEM/C-ADJ. button again to confirm the time. 
6. Each enable state as shown above will be cleared if the key is not pushed in10 seconds.

CLOCK SETTING

TIMER SETTING

1. After adjusting the clock, press the TIMER button for a few seconds, "      ON" and "00:00" appear on the display and 
    the HOUR digit  flashes.(F1)
2. 

Touch        or        on the unit or press        or        button on the remote control to adjust it.

3. Press the TIMER button again, the MINUTE digit will start flashing, adjust it by t

ouching        or        on the unit or 

    press      

  or        button on the remote control.

4. Press the TIMER button once more to confirm and order TIMER ON time.
5. After adjusting "TIMER ON", "      OFF" appears on the display and the HOUR digit flashes.(F2)
6. Repeat the above steps 2 to 3, and then press the TIMER button once more to confirm and order TIMER OFF time. 
7. Now the "TUNER" appears on the display with flashing, and then select the alarm mode of the “

TUNER, CD, USB, 

    CARD or IPOD" by touching        or        on the unit.
8. Press the TIMER button again, the timer "VOL" indicator appears on the display and flashes, adjust the timer 
    volume high or low by t

ouching        or        on the unit or press the        or        button on the remote control.

9. Each enable state as shown above will be cleared if the button is not pushed in 10 seconds.
10.After adjusting "TIMER ON" and "TIMER OFF", press the TIMER button, "      “ appears on the display.
11.The main unit will be switched on automatically at "TIMER ON" order and start playing, the main unit will be 
     switched off automatically at "TIMER OFF" order.
Note: If the display shows "ERROR" while you set the “TIMER ON”, it means both “TIMER ON” and “TIMER OFF” is 
          the same. In this case, please go to “TIMER OFF” to set the off time first. To switch TIMER function ON or OFF, 
          press TIMER button.     

0.495144s