Samsung Series P6+ 6500 User's Manual

Samsung Flat Panel TV User's Manual - Series P6+ 6500.
Download
Page  of 2
4.8, 1036 votes
background image

Step 4: Connect External Devices
Connecting an AV device (DVD/Blu-ray player, cable/satellite box, etc.)

Step 1: Install the Stand
Follow the steps below to connect the TV to the stand. (50 inch model only)

 

✎ NOTE

 

x Make sure to distinguish between the front and back of the Stand and 

Guide Stand when assembling them.

 

x Make sure that at least two persons lift and move the PDP TV.

 

x Stand the product up and fasten the screws. If you fasten the screws with 

the PDP TV placed down, it may lean to one side.

Connect the Guide Stand to the 

Stand using five screws (M4 X L12) 
as shown.

With your TV upright, connect the 

TV to the Stand.

Fasten two screws (M4 X L10) at 

position 1, and then fasten three 
screws (M4 X L10) at position 2.

s

s

s

s

s

s

Rear

Screws (M4 X L10)

1

s

s

s

s

s

2

Step 2: Install the Batteries into the Remote
To install batteries into your remote control, 
follow these steps:
1.  Lift the cover on the back of the remote 

upward as shown in the figure to the 
right.

2.  Install two AAA batteries.

 

✎ Make sure to match the + and - ends of the batteries to the diagram in 

the battery compartment.

3.  Replace the cover.

Step 3: Connect Power and Antenna or Cable

Quick Setup Guide

Congratulations on the purchase of your new Samsung TV. 
Read this setup guide to get your TV up and running quickly.

1-800-SAMSUNG (1-800-726-7864)
Samsung Electronics America, Inc.
85 Chal enger Road Ridgefield Park, NJ 07660-2112
Samsung Electronics Canada Inc.
55 Standish Court Mississauga, Ontario L5R 4B2
Cal  Center hours of operation: Mon-Sun, 9:00 AM -12 
AM EST.
To register this product, visit: www.samsung.com/
register.

STOP

Please do not return this unit.

If you have problems operating your 

TV, call:

1-800-SAMSUNG (1-800-726-7864)

For web support please visit:

www.samsung.com/support

Step 5: Run Plug & Play
When you turn on your TV for the first time, it automatically launches the Plug & 
Play function. With Plug & Play, you can select the On Screen Display language, set 
the clock mode, and launch the TV’s channel memorizing process. 
It also displays connection instructions similar to those in this guide.
To navigate while Plug & Play is running, press the Up, Down, Left or Right arrow 
buttons on your remote. To make a selection, press the ENTERE button. 
To skip a screen, press the MENU button. To turn on your TV, press the POWER 
button on the remote or on the TV. To run Plug & Play, follow these steps:
Using your remote control, select 

the language for the On Screen 
Display (OSD), and then press the 
ENTERE button.

Select Home Use, and then 

press the ENTERE button. 

If you select Store Demo, the TV will reset your picture and audio settings 
every 30 minutes.

Select Antenna Source. If Antenna Source is Air, Cable or Auto, you must 

select your cable system type. After selecting source, select Search; then 
press the ENTERE button on your remote.

 

✎ Most cable systems are Standard (STD) systems, If you are not sure about 

what kind of cable system you have, contact your cable company.

 

✎ If your TV is attached to a cable or satel ite box, skip Steps 3 through 5. After 

Plug & Play is complete, set your TV to Channel 3 or 4, according to the 
directions for your cable or satel ite box.

The TV memorizes the available channels. This process can take up to 45 

minutes.

After the TV has memorized the channels, choose the Clock Mode. Select 

Auto if you have a digital channel in your area. Select Manual if you don’t, or 
if you have a cable or satellite box. When done, press the ENTERE button.

 

✎ If you select Manual, the clock setting screen appears.

Select the Daylight savings time setting: Off or On, and then press the 

ENTERE button.

 

✎ This function is only available when the Clock Mode is set to Auto.
Select the time zone in which you live, and then press the ENTERE button.
After the time zone screen, The connection method for best HD screen 

quality is displayed. Press the Right arrow button on your remote to view 
each screen in succession. Press the Blue button to skip this section.

The Enjoy your TV. screen appears. Then press the ENTERE button.
Changing the Screen Size

Your TV has several screen size options, each designed to work best with specific 
types of video input. If you have a cable box or satellite receiver, it may have its own 
set of screen sizes as well.
To change the screen size, press the P.SIZE button on your remote. The first time 
you press it, your TV displays the current setting. Thereafter, each time you press 
the P.SIZE button, you change the size of the picture on the screen.
The following sizes are available:

16:9 Widescreen

4:3 Standard screen

Wide Fit

Zoom 1

Zoom 2

Screen Fit

 

✎ Screen Fit: Displays the full image without any cut-off when HDMI (720p / 

1080i / 1080p) or Component (1080i / 1080p) signals are inputted.

Changing the Picture Mode

Your TV has four preset Picture Modes with factory adjusted settings, each 
designed to give you an excellent picture under specific conditions.
The Picture Modes are listed and described in the table below:

Mode

Description

Dynamic

Brightens picture. For a vibrant, enhanced image in brightly lit or 
sunny room.

Standard

For a bright, detailed picture in a normally lit room.

Relax

For a comfortable, easy-on-the-eyes picture in a normally lit room.

Movie

For a studio quality cinema picture in a dimly lit or dark room.

To change the Picture Mode, follow these steps:
1.  With the TV on, press the TOOLS button on your remote. The Tools menu 

appears.

2.  Using the 

▲ or ▼ on your remote, select Picture Mode.

3.  On the Picture Mode menu, use the 

◄ or ► button on your remote to select 

the Picture Mode you want.

4.  Press the EXIT button to exit the menu.

Setting the Clock

Before you can use your TV’s On/Off Timer, you must set the clock. To set the 
clock, follow these steps:
1.  Turn on your TV, press the MENU button on your remote, then select Setup 

→ 

Time.

2.  Select Clock Mode, and then press the ENTERE button. 
3.  Choose Auto or Manual. 

 

x If you select Auto, the current time will be set automatical y using the time 

from a digital channel. 

 

x If you select Manual, you can set the Month, Day, Year, Hour, Minute 

and am/pm directly by pressing up, down, left and right arrow button on 
your remote.

4.  Press the RETURN button on your remote when done.

Connecting an audio device (Home Theater, etc.)

Connecting a PC

HDMI OUT

AUDIO OUT

COMPONENT OUT

AUDIO OUT

DVI OUT

AUDIO OUT

VIDEO OUT

AUDIO IN

OPTICAL

Analog Audio connection

Amplifier / DVD home theater

Using an Audio Cable

U Move   E Enter

Select Language of the OSD.

Menu Language 

:

Plug & Play

English
Español
Français

DVI OUT

AUDIO OUT

AUDIO OUT

PC OUT

HD connection

Using an HDMI to DVI Cable

Using a D-Sub Cable

Digital Audio connection

Using an Optical Cable

Digital Audio System

Best Connection

HD connection (up to 1080p)

Using an HDMI Cable

DVD, Blu-ray player, HD cable box, 

HD STB (Set-Top-Box) satel ite 

receiver

Device

HD connection (up to 1080p)

Very Good Connection

Using an HDMI to DVI Cable

Device

Using a Component Cable

Good Connection

Component connection (up to 1080p)

DVD, Blu-ray player, cable box, 

STB satel ite receiver, VCR

Device

Lowest Quality Connection

Audio/Video connection (480i only)

Using an Audio/Video Cable

DVD, Blu-ray player, cable box, 
STB satel ite receiver, VCR

Device

s

s

s

s

s

Top view

Rear

Front

Rear

Guide Stand

Screws (M4 X L12)

Stand

Use one of the connections below to connect your 
TV to an external A/V device.
We recommend using HDMI for the highest picture 
quality.

 

✎ When connecting to AV IN, the color of the AV 

IN [Y/VIDEO] jack (green) will not match the 
video cable (yel ow).

Connect your TV to your Home Theater or other 
audio device  to enjoy enhanced Sound quality.

Connect your TV to a PC to use it as a Monitor.

VHF/UHF Antenna

Connect Ant In to

•  Wal  cable jack 
•  VHF/UHF Antenna 
•  Cable or Satel ite box 

Ant or Cable Out

Use a 75 ohm (round) cable.

or

Antenna Cable 

(Not Supplied)

Audio Cable (Not Supplied)

HDMI to DVI Cable (Not Supplied)

Audio Cable (Not Supplied)

Audio Cable (Not Supplied)

Component Cable (Not Supplied)

HDMI Cable (Not Supplied)

Video Cable (Not Supplied)

Optical Cable (Not Supplied)

Audio Cable (Not Supplied)

HDMI to DVI Cable 

(Not Supplied)

D-Sub Cable (Not Supplied)

Audio Cable (Not Supplied)

Audio Cable (Not Supplied)

[QSG]BN68-02646A-01Eng.indd   1

2010-09-03   오후 5:45:10

Related Manuals for Samsung Series P6+ 6500

0.569690s