Samsung BN68-02621A-04 User's Manual

Samsung Flat Panel TV User's Manual - BN68-02621A-04.
Download
Page  of 2
4.3, 2344 votes
background image

English - 1

• Wall cable jack or
• VHF/UHF  

   Antenna or
• Cable or Satellite 

   box Ant or Cable    

   Out 

Quick Setup Guide

1-800-SAMSUNG (1-800-726-7864)
Samsung Electronics America, Inc.
85 Challenger Road Ridgefield Park, NJ 07660-2112
Samsung Electronics Canada Inc.
55 Standish Court Mississauga, Ontario L5R 4B2
Call Center hours of operation: Mon-Sun, 9:00 AM -12 AM EST.
To register this product, visit : www.samsung.com/register.

Congratulations on the purchase of your new Samsung TV. Read this 

setup guide to get your TV up and running quickly.

STOP

Please do not return this unit.

If you have problems operating your 

TV, cal:

1-800-SAMSUNG (1-800-726-7864)

For web support please visit:

www.samsung.com/support 

Step 3 : Connect Power and Antenna or Cable

Step 4 Connect External Devices

Connecting an AV device (Blu-ray player, cable/satellite box, etc.)

Connecting an audio device
Connect your TV to your Home Theater or other audio  

device to enjoy enhanced sound quality.

Connecting a PC
Connect your TV to a PC to use it as a Monitor.

Use a 75 ohm (round) cable. 

Using an D-Sub Cable

AUDIO OUT

PC OUT

PC

HD connection

Using an HDMI Cable

DVI OUT

AUDIO OUT

PC

Step 2 : Install the Batteries into the Remote

To install batteries into your remote control, follow these steps:

1.  Lift the cover on the back of the remote upward  

as shown in the figure to the right.

2.  Install two AAA batteries.

Make sure to match the + and - ends of  

 

the batteries to the diagram in the battery  

compartment.

3.  Replace the cover.

Connect AnT In to:

Using an HDMI Cable 

DVD / Blu-Ray player / HD Cable Box /  

HD Satellite receiver (STB)

HDMI OUT

Device

AV IN 2

(HDD

)

USB

1

USB

2

AV IN 2

(HDD)

US
B

1

U

S

B

2

HDMI IN 

4

HD connection (up to 1080p)

Best Connection

Step 1 : Install the Stand

Follow the steps below to connect the TV to the stand.

Make sure to distinguish between the front and back of the Stand and Guide 

 

Stand when assembling them.
Make sure that at least two people lift and move the LCD TV.

 

Lay the product down, with the screen facing up and fasten the screws.

 

Using a Component Cable 

VCR / DVD / Blu-ray player / Cable Box 

/ Satellite receiver

Component connection (up to 1080p)

Device

 

(HDD)

USB1

USB2

(HD
D

)

US
B1

USB2

HDMI IN 

4

AV IN 2

COMPONENT OUT

Good Connection

AUDIO OUT

HD connection (up to 1080p)

Very Good Connection

Using an DVI to HDMI Cable 

DVD / Blu-Ray player /  

Cable Box /  

Satellite receiver (STB)

Device

 

AV IN 2

(HDD

)

USB

1

USB

2

AV IN 2

(HDD)

US
B

1

U

S

B

2

HDMI IN 

4

DVI OUT

AUDIO OUT

1

2

Digital Audio connection

Using an Optical Cable 

Digital Audio System  

OPTICAL

Using an Audio Cable

Amplifier / DVD Home Theater

Analog Audio connection

Device

   

AV IN 2

(HDD

)

USB

1

USB

2

AV IN 2

(HDD)

US
B

1

U

S

B

2

HDMI IN 

4

AUDIO IN

Power Input

or

Getting Started

For the very best picture quality, select HD signal sources and use HDMI cables and connections. 

Note that many digital cable programs are not in HD. Check with your video provider to ensure your 

are receiving HD signals.

The HDMI connection carries 

digital video and audio.

Step 5 : Run Plug & Play

When you turn on your TV for the first time, it automatically launches 

the Plug & Play function. With Plug & Play, you can select the On 

Screen Display language, set the clock mode, and launch the TV’s 

channel memorizing process. It also displays connection instructions 

similar to those in this guide.
To navigate while Plug & Play is running, press the Up, Down, Left or 

Right arrow buttons on your remote. To make a selection, press the 

EnTErE button. To skip a screen, press the MEnU button.
To turn on your TV, press the POwEr button on the remote or press 

the POwEr button on the TV. To run Plug & Play, follow these steps:

1

Select Language of the OSD.

Language             

 : English                          

Plug & Play

U Move   E Enter

English
Español
Français

On the Language screen, select the language for the On Screen 

Display (OSD) using your remote control, and then press  

EnTErE button. The Home Use screen appears.

2

Select ‘Home Use’ when instal ing this TV in your home.

Plug & Play

L Move   E Enter

Store Demo

Home Use

 

Select Home Use, and then press EnTErE button. If you select  

Store Demo, the TV will reset your picture and audio settings every 

30 minutes. After you press EnTErE button , the Antenna Source 

screen appears.

3

Select the Antenna source to memorise.

Air
Cable
Auto

Plug & Play

U Move   E Enter   m Skip 

Start
Start
Start

If your TV is only attached to an antenna, select Air. If your TV is only 

attached to cable and you have no cable box, select Cable. If your 

TV is attached to an antenna and cable with no box, select Auto. 

When done, press EnTErE button on your remote. The Select 

Cable System screen appears.

IMPORTANT: If your TV is attached to a cable or satellite box, 

skip Steps 3 through 5. After Plug & Play is complete, set your TV to 

Channel 3 or 4, according to the directions for your cable or satellite box.

4

Selects the cable system.

Analog
Digital

Plug & Play

U Move    E Enter    m Skip 

STD

HrC

IrC

STD

HrC

Start

IrC

If your TV is attached to a cable system and you have no cable box, 

you must select your cable system type. If you have Digital cable, you 

must select the cable system type for both Analog and Digital.
After you have selected the cable system type, select Start, and then 

press the EnTErE button on your remote. 

Most cable systems are Standard 

 

(STD) systems. If you are not 

sure about what kind of cable system you have, contact your 

cable company.

5

Auto Program in Progress.

DTV Cable : --                   Cable : --                    Cable     28

Plug & Play

E Enter   m Skip 

Stop

15%

The TV memorizes the available channels. This process can take 

up to 45 minutes.

6

Set the Clock Mode.

Clock Mode 

 : English                          

Plug & Play

U Move   E Enter   m Skip

Auto
Manual

After the TV has memorized the channels, choose the Clock 

Mode. Select Auto if you have a digital channel in your area. Select 

Manual if you don’t, or if you have a cable or satellite box. When 

done, press EnTErE button.

If you select 

 

Manual, the clock setting screen appears.

7

Set to daylight saving time.

DST 

 : English                          

Plug & Play

U Move   E Enter   m Skip

Off
On
Auto

Select the daylight savings time setting: Off, On, or Auto, and then 

press EnTErE button.

8

After the time zone screen, 

The connection method 

for best HD screen quality 

is displayed. Press Right 

arrow button on your 

remote to view each screen 

in succession. Press the 

MEnU button to skip this 

section.

9

The Enjoy your TV screen 

appears. Then press 

EnTErE button.

Stand

Screw

Lowest Quality Connection

Using an Audio/Video Cable 

VCR / DVD / Blu-ray player / Cable Box / 

Satellite receiver

Audio/Video connection (480i only)

VIDEO OUT

VCR

(HDD)

USB1

USB2

(HD
D

)

US
B1

USB2

HDMI IN 

4

AV IN 2

AUDIO OUT

[LC350-QSG]BN68-02621A-04Eng-0831.indd   1

2010-09-01   �� 8:54:04

Related Manuals for Samsung BN68-02621A-04

0.573635s