RCA RT2770 Owner's Manual

RCA Audio Owner's Manual - RT2770.
Download
Page  of 2
4.9, 1463 votes
background image

152-27700-0285-001

DVD/SAT/CAB

Connecting to Audio Components

Connecting the Speakers
Speaker wires are color-coded to match the

terminals. Connect the speaker wire from the

back of each speaker to the corresponding

color terminal at the back of the unit. Press

down the tab to open the terminal and insert

the wire. Release the tab to lock wire in

the terminal.

When connecting the speakers, make sure the

polarities (“+” speaker wire to “+” on the unit.

For example, red wire to red terminal on the

unit) of speaker wires and terminals match.

If the cords are reversed, the sound will

be distorted. Do not let the speaker wires

touch each other, it will damage

the speaker.

When connecting subwoofer, connect

subwoofer control cable (red/black striped) at

the back of the subwoofer to the subwoofer

control jack on the unit’s rear panel, then press

POWER ON/OFF

on the subwoofer speaker to

turn it on.

Content of Box

One main unit

One remote control with batteries

One pair of front speakers, one pair of rear

speakers, one center speaker and

one subwoofer

One pig-tail antenna wire

One AM loop antenna

One coaxial digital cable

One 3.5mm stereo cable for line-in

OneUser Manual

Set up and Maintenance of

the Unit
Provide spaces for su cient ventilation

as indicated:

Do not connect to the AC power cords until

all connections are completed.

Do not use your set immediately after

transferring it from a cold place to a warm

place: there is risk of condensation.

Do not expose your set to water and

excessively high temperatures.

After having disconnected your set, clean the

case with a soft cloth, or with a slightly damp

leather chamois. Never use strong solvents.

Protect your Components from

Overheating

Do not block ventilation holes in any

component. Arrange the components so that

air can circulate freely.

Do not stack components directly on top of

each other.

Do not place the unit near other components

that generate heat such as heating vents.

Allow adequate ventilation when placing

your components in a stand.

Place an

near the top shelf of the

stand so heated air rising from it will not

a ect other components. If you have a

satellite receiver, you should place it on the

top shelf.

TV Connections
TVs with RF input may need a RF modulator

(not included) for inputting audio signals.

The illustration shown above may varies from

your actual RF modulator, please refer to your

RF modulator manual.

Connecting the Antennas
Connect the AM and FM antennas to the AM

and FM terminals on the system’s back panel.

They must be hooked up in order to receive

clear reception. For FM reception, extend

antenna to its full length. For AM reception,

rotate the antenna horizontally to get

better reception.

AM Loop Antenna and FM Indoor Antenna

1. Uncoil the antenna wire and locate the base

end of the AM antenna.

2. Press down on the antenna tab to open

the terminal.

3. Insert the antenna wires into the terminal

and release the tabs to secure the wires

in place.

4. Make sure the white wire on the AM loop

antenna is inserted into the AM LOOP

terminal and other wire is inserted into the

ground loop terminal.

Technical
Product: Audio Receiver with Dolby Digital

Brand: RCA

Model: RT2770

Electrical Consumption
Power Supply: 120V ~ 60Hz

Power consumption: 90 Watts

For Your Safety
The AC power plug is

polarized (one blade is wider

than the other) and only

into AC power outlets one

way. If the plug won’t go into

the outlet completely, turn the

plug over and try to insert it the other way. If it

still won’t

contact a

electrician to

change the outlet, or use a di erent one. Do

not attempt to bypass this safety feature.

CAUTION: To prevent electric shock, match

wide blade of plug to wide slot, fully insert.

Important Safety Instructions

Connections and Setup

Connections and Setup

Connections and Setup

FCC Information

FCC Information

Connections and Setup

It is important to read this instruction book prior to using your new product for the

time.

EXPORTER

www.rcaaudiovideo.com

Printed In China

RT2770 IB V2.2 (EN)

RT2770

user manual

This audio system has earned

the ENERGY STAR.

Left and right

front speakers

Left and right

rear speakers

Subwoofer

Center speaker

AM loop antenna

User manual

Coaxial digital

cable

Main unit

3.5mm stereo

cable for

line-in

Pig-tail

antenna wire

Remote

control with

batteries

DVD/SAT/CAB

C OAXIAL OP TIC AL

Digital Connection

This unit provides one optical and one coaxial digital input jacks for the connection of

your components.

To connect a SAT receiver or DVD player with a digital output, use an optical digital cable (not

included) or coaxial digital cable (included) to carry the audio signal and enjoy Dolby Digital

sound quality.

One optical or coaxial cable is needed for each SAT receiver or DVD player.

Digital Input

Connect components capable of

outputting Dolby digital (e.g. DVD or

SAT) or standard PCM (CD) format

digital signals. Read section on "Input

Signal Setting" under "Advanced

Sound Control" carefully to adjust the

matching input settings.

Note:Optical and coaxial cables carry only the audio portion of the signal.

SUBWOOFER
CONTROL

Use this jack on

the rear panel to

connect to the

subwoofer

control cable

(red/black

striped) of the

subwoofer.

Use this jack on

the rear panel

to connect

another active

subwoofer

other than the

one supplied.

SUBWOOFER

AUDIO OUT

Center Speaker

Front Speakers

Right

Left

Right

Left

Rear Speakers

(Surround Sound)

Subwoofer

White/grey

or

black

striped

Red/grey

or

black

striped

Green/grey or

black striped

Purple/grey

or black

striped

Blue/grey or black striped

Grey/black striped

Optical Digital In (Audio)

Connect to optical digital output of DVD, SAT or other compatible

devices using the optical Fiber Cable (not included).

Coaxial Digital In (Audio)

Connect to coaxial digital output of DVD, SAT or other

compatible devices using the coaxial digital cable (included).

DVD/SAT/CAB

DVD/SAT

Please read and save for

future reference
Some of the following information may not

apply to your particular product; however, as

with any electronic product, precautions should

be observed during handling and use.

Read these instructions.

Keep these instructions.

Heed all warnings.

Follow all instructions.

Do not use this apparatus near water.

Clean only with dry cloth.

Do not block any ventilation openings.

Install in accordance with the

manufacturer’s instructions.

Do not install near any heat sources such as

radiators,heat registers, stoves, or other

apparatus (including

that

produce heat.

Do not defeat the safety purpose of the

polarized or grounding-type plug. A

polarized plug has two blades with one

wider than the other. A grounding type plug

has two blades and a third grounding prong.

The wide blade or the third prong is

provided for your safety. If the provided plug

does not

into your outlet, consult an

electrician for replacement of the

obsolete outlet.

Protect the power cord from being walked

on or pinched particularly at plugs,

convenience receptacles, and the point

where they exit from the apparatus.

Only use attachments/accessories

by

the manufacturer.

Use only with the cart, stand, tripod, bracket,

or table

by the manufacturer, or

sold with the apparatus. When a cart is used,

use caution when moving the cart/apparatus

combination to avoid injury from tip-over.

Unplug this apparatus during lightning

storms or when unused for long periods

of time.

Refer all servicing to

service

personnel. Servicing is required when the

apparatus has been damaged in any way,

such as power-supply cord or plug is

damaged, liquid has been spilled or objects

have fallen into the apparatus, the apparatus

has been exposed to rain or moisture, does

not operate normally, or has been dropped.

Additional safety information

Apparatus shall not be exposed to dripping

or splashing and no objects

with

liquids, such as vases, shall be placed on

the apparatus.

Always leave su cient space around the

product for ventilation. Do not place product

in or on a bed, rug, in a bookcase or cabinet

that may prevent air

through

vent openings.

Do not place lighted candles, cigarettes,

cigars, etc. on the product.

Connect power cord only to AC power

source as marked on the product.

Care should be taken so that objects do not

fall into the product.

Do not attempt to disassemble the cabinet.

This product does not contain customer

serviceable components.

If your product operates on batteries,

adhere to the following precautions:

A.Any battery may leak electrolyte if mixed

with a di erent battery type, if inserted

incorrectly, or if all batteries are not replaced

at the same time.

B. Any battery may leak electrolyte or explode

if disposed of in

or an attempt is made

to charge a battery not intended to

be recharged.

C. Discard leaky batteries immediately. Leaking

batteries can cause skin burns or other

personal injury. When discarding batteries,

be sure to dispose of them in the proper

manner, according to your state/provincial

and local regulations.

]

Portable Cart Warning

Positioning Speakers

1. Left, Right (Front Speakers)

Front speakers carry primarily music and

sound e ects.

2. Center

In surround mode, the center speaker carries

most of the dialog as well as music and e ects.

It should be set between the left and

right speakers.

3. Surround (Rear Speakers)

The rear speakers’ overall sound balance should

be as close as possible to the front speakers.

Proper placement is vital to establish an evenly

distributed sound

Subwoofer
A subwoofer is designed to reproduce powerful

low bass e ects (explosions, the rumble of

spaceships, etc.) which dramatically heighten

the action on the screen.

Magnetic Shielding
Speakers placed less than two feet from the TV

set must be magnetically shielded in order to

prevent picture distortion. Front speakers

provided with this unit are magnetically

shielded to protect your TV set.

Front Speaker Placement
Follow the suggestions for speaker placement

below to get the best results.

Alignment

Align the center speaker evenly with (A) or

slightly behind (B) (the left and right speakers),

but not ahead of them.

Angle

Place the left and right speakers to form a 45-

degree angle with your favorite viewing

position to duplicate the soundtrack

mixer’s perspective.

Height

The mid- and high-frequency drivers of the

three front speakers should be as close as

possible to the same height. This often requires

placing the center speaker directly on top (A)

or beneath (B) the TV set.

Better Surround Placement
Location

If possible, place surround speakers to either

side of the listening area, not behind it.

Height

If space permits, install surround speakers 2-3

feet above viewers. This helps to minimize

localization e ects.

Aiming

Aim surround speakers straight across the

room, not down at viewers, to help create a

more open, spacious surround sound

Alternative Surround Placement
Rear wall

If rear wall mounting is the only choice, aim

the speakers at each other (A), towards the

front (B) or towards the sidewalls (C, D).

Experiment with placement until sounds seem

to surround you, rather than come from

behind you.

No adjacent walls

Surround speakers can go on stands facing

each other to approximate sidewall mounting

(A), or to the sides or rear of the viewing area,

aimed upwards; they can go right on the

r,

or preferably, a few feet o the

such as

on end tables (B).

Front Surround Mode

Speaker Placement

1

Follow the suggestion for speaker placement in

the section before.

2

If placing the rear speakers (surround speakers)

at the back is not a good choice for you, you

can use the Front Surround sound E ect(FSsE).

Follow the following instruction for setting

the speakers. (See section “Front Surround

Sound E ect (FSsE) Setting” under “Advanced

Sound Control” for details).

Mounting the Speakers

1. Place the front speaker upside down.

2. Slide in the hinge to the bottom of the front

speaker until the ‘click’ sound is heard.

3. Slide in the rear speaker to the hinge until

the ‘click’ sound is heard.

4. Attach the supplied speaker stand to the

top of the front speaker.

Adjusting the Angle of the Speakers

To achieve the best Front Surround sound

E ect (FSsE), adjust the mounted front left and

the rear left speakers to the left for an angle of

25o - 45 o from the center.

Adjust the mounted front right and rear right

speakers to the right in the same way.

After adjusting the angle, the speaker should

look like this illustration.

Disconnecting the Speakers
1. To unlock the speakers, press and hold the

hinge spring as illustrated below.

2. Slide out the rear speaker from the hinge.

3. Press and hold the two hinge springs.

4. Slide out the hinge from the front speaker.

Connections and Setup

Connections and Setup

Connections and Setup

3

3

1

1

2

4

Courtesy Dolby Laboratories

Note: Place the rear speakers and

subwoofer a foot or more away from

TV when using the Front Surround sound
E ect (FSsE).

Courtesy Dolby Laboratories

Courtesy Dolby Laboratories

A

B

Courtesy Dolby Laboratories

Courtesy Dolby Laboratories

Courtesy Dolby Laboratories

1

1

Note: Match the front left and rear left

speakers together and match the front right
and rear right speakers together.

Front

Speaker

1

2

Rear

Speaker

Front

Speaker

Rear

Speaker

Front

Speaker

2

Note: Place the rear speakers and

subwoofer a foot or more away from TV

whenusing the Front Surround sound

E ect (FSsE).

Press

and

hold

Rear

Speaker

Front

Speaker

1

2

Hinge Spring

3

4

Press

and

hold

Hinge Spring

TV

RF in

RF out

Audio cable

RF cable

RF modulator

Digital Connections
The digital audio jacks can accept Dolby Digital (AC-3) or PCM signals when compatible

components are connected.

AVC Multimedia

7

This symbol indicates “dangerous voltage”

inside the product that presents a risk of

electric shock or personal injury.

This symbol indicates

important instructions ac-

companying the product.

WARNING

RISK OF ELECTRIC SHOCK

.

DO NOT OPEN

To reduce risk of electrical shock, do not

remove cover or back (no user serviceable

parts inside). Refer servicing to

d

personnel.

FCCINFORMATION
NOTE: ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforaClassBdigitaldevice,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment o and on, the user is encouraged to try to correct the

interference by one or more of the following measures:
¶ Reorient or relocate the receiving antenna.

¶ Increase the separation between the equipment and receiver.

¶ Connect the equipment into an outlet on a circuit

from that to which the receiver is

connected.

¶ Consult the dealer or an experienced radio/TV technician for help.

WARNING: Changes or modi cations to this unit not expressly approved by the party responsible for

compliance could void the user's authority to operate the equipment.
This class B digital apparatus meets all requirements of the Canadian Interference–Causing

EquipmentRegulations.
TheShockHazardMarkingandAssociatedGraphicalSymbolisprovidedonthebottompanelofunit.
Refer to the

cation/rating label located on the back panel of your product for its proper

operating voltage.
IMPORTANT:

The power cord can be unplugged to turn o the main power to the unit. It should also

be easily accessible in an emergency.

¶ Leave su cient space around the appliance to allow adequate ventilation: 10cm on either side

and at the back, as well as 7cm above it are ideal.

WARNING: To reduce the risk of

or electric shock,

do not expose this apparatus to rain or moisture.

Service Information
This product should be serviced only by those

specially trained in appropriate servicing

techniques. For instructions on how to obtain

service, refer to the warranty included in

this user manual.

Connecting for Power
Make sure you connect all your other

electronic components and the speakers before

plugging your unit into the outlet. Plug the

power cord in the wall outlet, matching the

wide blade of the plug with the wide slot in

the outlet. Be sure to insert the

plug completely.

Headset Safety

Do not play your headset at a high volume.

Hearing experts warn against extended

high-volume play.

If you experience a ringing in your ears,

reduce volume or discontinue use.

U Y

ou should use extreme caution or

temporarily discontinue use in potentially

hazardous situations.

U

Even if your headset is an open-air type

designed to let you hear outside sounds,

don’t turn up the volume so high that you

are unable to hear what is around you.

U

Excessive sound pressure from

earphones and headphone can cause

hearing loss.

D. Battery shall not be exposed to excessive

heat such as sunshine,

or the like

Top

Hinge

Bottom

3

4

0.781121s