Radio Shack 63-987 User's Manual

Radio Shack Clock User's Manual - 63-987.
Download
Page  of 3
4.2, 1204 votes
background image

© 2002 RadioShack Corporation.

All Rights Reserved.

RadioShack and RadioShack.com are trademarks 

used by RadioShack Corporation.

63-987

OWNER’S MANUAL — Please read before using this equipment.

Your RadioShack Atomic Projection Clock 
combines a simple design with advanced 
technology. You can set the clock to project 
the current time on a wall or the ceiling for 
easy nighttime viewing.

You can also set the clock to automatically 
set the time and date, using a 60 kHz 
longwave radio signal from radio station 
WWVB. The clock checks the radio signal 
several times each day and automatically 
updates the time and date, providing the 
most accurate time possible. Or, if you are 
unable to receive the time-setting signal, you 
can set the clock manually.

Large Liquid Crystal Display — makes the 
clock easy to read. The current time and 
alarm time, the time zone you are in, and the 
date and day of the week appear on the 
display.

Adjustable Projector — lets you project the 
time on a wall or ceiling, rotate the image to 
the desired angle, and focus the image for 
clarity.

Three Languages — lets you review the day 
of the week in English, French, or Spanish.

Display Backlight — lets you see all the 
information on the screen, even in the dark.

Indoor Thermometer — lets you monitor the 
room’s temperature.

+056#..+0)"

$#66'4+'5
Your clock requires 2 AA batteries (not 
supplied) for power. For the best 
performance and longest life, we recommend 
RadioShack alkaline batteries.

Cautions:

• Use only fresh batteries of the required 

size and recommended type.

• Do not mix old and new batteries, 

different types of batteries (standard, 
alkaline, or rechargeable), or 
rechargeable batteries of different 
capacities. 

1. Place your finger in the recess above the 

battery compartment cover and lift off the 
cover.

2. Place the batteries in the compartment 

as indicated by the polarity symbols (+ 
and –) marked inside.

3. Replace the cover.

When the display dims, the clock stops 
operating properly, or 

ô (low battery icon) 

appears, replace the batteries.

Warning: Dispose of old batteries promptly 
and properly. Do not burn or bury them.

Caution: If you do not plan to use the clock 
with batteries for a month or more, remove 
the batteries. Batteries can leak chemicals 
that can destroy electronic parts.

Note: Installing batteries resets the clock.

75+0)"#%"219'4
You can save battery power by using the 
supplied 3V, 200 mA AC adapter to power 
the projector. Be sure to install batteries to 
power the clock, as the AC adapter does not 
power the clock.

Cautions:

You must use a Class 2 power 
source that supplies 3V DC 
and delivers at least 200 mA. 

Its center tip must be set to positive and 
its plug must fit the clock's DC 3V jack. 
The supplied adapter meets these 
specifications. Using an adapter that 
does not meet these specifications could 
damage the clock or the adapter.

• Always connect the AC adapter to the 

clock before you connect it to AC power. 
When you finish, disconnect the adapter 
from AC power before you disconnect it 
from the clock.

1. Plug the AC adapter’s tip into the clock’s 

DC 3V

 jack (in the recess on the bottom 

of the clock).

2. Route the adapter’s cord through the slot 

marked DC 3V on the back of the clock.

3. Plug the AC adapter’s other end into a 

standard AC outlet.

$#5+%"12'4#6+10

As soon as you install the batteries, all 
display segments briefly appear. 

7Cý'(0&&

7Cý'(

7Cý'

7C

the seconds, 

'Cý':

'Cý'

'C  (January 1), and the 

current indoor temperature appear. 

For about 3 minutes after you connect power, 
the clock scans for a radio signal and 

÷ 

flashes. When the clock receives a strong 
signal, it automatically sets the time and date. 
The clock checks the radio signal six times a 
day, at about 2:00 AM, 3:00 AM, 4:00 AM, 
9:00 AM, 3:00 PM, and 9:00 PM (as shown 
on the clock).

Notes: 

• On very cloudy and stormy days, the 

signal might not be strong enough to 
reset the clock. If the clock does not 
receive a strong radio signal, you can set 
the time and date manually. (See 
“Manually Setting the Time, Date, and 
Language” on Page 2.)

• If the clock does not receive a strong 

signal within about 2 minutes, it stops 
scanning and looks for a signal again at 
the next preprogrammed time.

The time zone 

F (Pacific), C (Mountain), 9 

(Central), or 

; (Eastern) appears in the map 

on the right of the screen. While the clock is 
scanning for a signal, repeatedly press ZONE 
until the desired time zone is highlighted.

Your clock measures and displays the indoor 
temperature between 23° and 122°F (–5° to 
50°C). If the temperature goes above or 

!

((SNOOZE))

CLOCK

8 9

ALARM

ZONE

#VQOKE"2TQLGEVKQP"%NQEM

0.584358s