Pioneer CD Player DEH-P5100UB User's Manual

Pioneer CD Player User's Manual - CD Player DEH-P5100UB.
Download
Page  of 6
4.2, 1647 votes
background image

Installation

English

Installation

English

Connecting the unit

English

 Note

•  Check all connections and systems before final 

installation.

•  Do not use unauthorized parts. The use of 

unauthorized parts may cause malfunctions.

•  Consult with your dealer if installation requires 

drilling of holes or other modifications of the 

vehicle.

•  Do not install this unit where:

— it may interfere with operation of the vehicle.

— it may cause injury to a passenger as a result 

of a sudden stop.

•  The semiconductor laser will be damaged if it 

overheats. Install this unit away from hot places 

such as near the heater outlet.

•  Optimum performance is obtained when the unit 

is installed at an angle of less than 60°.

60°

DIN Front/Rear-mount

This unit can be properly installed either from  

“Front” (conventional DIN Front-mount) or 

“Rear” (DIN Rear-mount installation, utilizing 

threaded screw holes at the sides of unit 

chassis). For details, refer to the following 

instal ation methods.

DIN Front-mount

 Installation with metal strap and 

screws

1.  Insert the mounting sleeve into the 

dashboard.

•  When installing in a shallow space, use a 

supplied mounting sleeve. If there is enough 

space behind the unit, use factory supplied 

mounting sleeve.

2.  Secure the mounting sleeve by 

using a screwdriver to bend the 
metal tabs (90°) into place.

Dashboard

Mounting sleeve

53

182

3.  Install the unit.

•  Use commercially available parts when 

installing.

Screw (M4

˜8)

Screw

Metal strap

Nut

Firewall or 
metal support

•  Make sure that the unit is installed securely 

in place. Unstable installation may cause this 

unit to malfunction, such as sound skip.

Removing the Unit

1.  Extend top and bottom of the trim 

ring outwards to remove the trim 
ring. When reattaching the trim 
ring, push the trim ring onto the 
unit until it clicks. (If the trim ring is 
attached upside down, the trim ring 
will not fit properly.)

•  It becomes easy to remove the trim ring if the 

front panel is released.

Trim ring

2.  Insert the supplied extraction keys 

into both sides of the unit until 
they click into place.

3.  Pull the unit out of the dashboard.

DIN Rear-mount

1.  Extend top and bottom of the trim 

ring outwards to remove the trim 
ring. When reattaching the trim ring, 
push the trim ring onto the unit until 
it clicks. (If the trim ring is attached 
upside down, the trim ring will not 
fit properly.)

•  It becomes easy to remove the trim ring if the 

front panel is released.

Trim ring

2.  Determine the appropriate position 

where the holes on the bracket and 
the side of the unit match.

3.  Tighten two screws on each side.

•  Use either truss screws (5 mm × 8 mm) 

or flush surface screws (5 mm × 9 mm), 

depending on the shape of screw holes in the 

bracket.

Factory radio mounting bracket

Screw

Dashboard or Console

Fastening the front panel

If you do not plan to detach the front panel, 

the front panel can be fastened with supplied 

screw.

Screw

 Note

•  When this unit is installed in a vehicle without 

ACC (accessory) position on the ignition switch, 

red cable must be wired to the terminal that 

can detect the operation of the ignition key. 

Otherwise, battery drain may result.

ACC

ON

S

T

A

R

T

O

FF

      

ON

S

T

A

R

T

O

FF

ACC position

      

No ACC position

•  Use this unit in other than the following 

conditions could result in fire or malfunction.

— Vehicles with a 12-volt battery and negative 

grounding.

— Speakers with 50 W (output value) and 4 ohm 

to 8 ohm (impedance value).

•  To prevent short-circuit, overheating or 

malfunction, be sure to follow the directions 

below.

— Disconnect the negative terminal of the 

battery before installation.

— Secure the wiring with cable clamps or 

adhesive tape. To protect the wiring, wrap 

adhesive tape around them where they lie 

against metal parts.

— Place all cables away from moving parts, such 

as gear shift and seat rails.

— Place all cables away from hot places, such 

as near the heater outlet.

— Do not pass the yellow cable through a hole 

into the engine compartment to connect to a 

battery.

— Cover any disconnected cable connectors 

with insulating tape.

— Do not shorten any cables.

— Never cut the insulation of the power cable of 

this unit in order to share the power to other 

equipment. Current capacity of the cable is 

limited.

— Use a fuse of the rating prescribed.

— Never wire the speaker negative cable directly 

to ground.

— Never  band  together  multiple  speaker’s 

negative cables.

•  Control signal is output through blue/white cable 

when this unit is powered on. Connect it to an 

external power amp’s system remote control or 

the vehicle’s auto-antenna relay control terminal 

(max. 300 mA, 12 V DC). If the vehicle is equipped 

with a glass antenna, connect it to the antenna 

booster power supply terminal.

•  Never connect blue/white cable to external 

power amp’s power terminal. Also, never connect 

it to the power terminal of the auto antenna. 

Otherwise, battery drain or malfunction may 

result.

•  IP-BUS connectors are color-coded. Be sure to 

connect connectors of the same color.

•  Black cable is ground. This cable and other 

product’s ground cable (especially, high-current 

products such as power amp) must be wired 

separately. Otherwise, fire or malfunction may 

result if they are accidentally detached.

<KOKNX>  <08K00000>

 Printed 

in 

Thailand

 Imprimé 

en 

Thaïlande

<

QRD3031-A/N> UC

CD RECEIVER

AUTORADIO CD

RADIO CD
DEH-P5100UB

Installation Manual

Manuel d’installation

Manual de instalación

0.587022s