Whirlpool WED9151YW Manuals
Whirlpool Clothes Dryer WED9151YW manuals download on ManualAgent: User's Manual, Installation Manual, Use & Care Manual, Warranty Information, Dimension Guide, Ventilation Specification
-
Document Outline
- electronic DRYER
- sécheuse électronique
- dryer Safety
- QUICK START GUIDE /DRYER USE
- Cycles
- Automatic Cycles
- Timed Cycles
- Air Dry
- When using Air Dry:
- Check that coverings are securely stitched.
- Shake and fluff pillows by hand periodically during the cycle.
- Dry item completely. Foam rubber pillows are slow to dry.
- Three short tones sound if an unavailable combination is selected. The last selection will not be accepted.
- dryer care
- Cleaning the Dryer Location
- Cleaning the Lint Screen
- Do not run the dryer if the lint screen is loose, damaged, blocked, or missing. Doing so can cause overheating and damage to both the dryer and fabrics.
- If lint falls off the screen into the dryer during removal, check the exhaust hood and remove the lint. See “Venting Requirements.”
- As needed cleaning:
- To wash:
- 1. Roll lint off the screen with your fingers.
- 2. Wet both sides of lint screen with hot water.
- 3. Wet a nylon brush with hot water and liquid detergent. Scrub lint screen with the brush to remove residue buildup.
- 4. Rinse screen with hot water.
- 5. Thoroughly dry lint screen with a clean towel. Replace screen in dryer.
- Cleaning the Dryer Interior
- Removing Accumulated Lint
- Vacation, Storage, and Moving Care
- Non-Use or Storage Care
- Moving care
- Reinstalling the dryer
- Changing the Drum Light
- To change the drum light:
- 1. Unplug dryer or disconnect power.
- 2. Open the dryer door. Locate the light bulb cover on the back wall of the dryer. Remove the screw located in the lower right corner of the cover. Remove the cover.
- 3. Turn bulb counterclockwise. Replace the bulb with a 10-watt appliance bulb only. Replace the cover and secure with the screw.
- 4. Plug in dryer or reconnect power.
- To change the drum light:
- Changing the Drum Light
- troubleshooting
- First try the solutions suggested here and possibly avoid the cost of a service call... For additional recommendations, refer to your Installation Instructions.
- Dryer Operation
- Dryer will not run
- Is the dryer door firmly closed?
- Was the START/PAUSE button firmly pressed? Large loads may require pressing and holding the Start/Pause button for 2-5 seconds.
- Has a household fuse blown, or has a circuit breaker tripped? There may be 2 household fuses or circuit breakers for the dryer. Check that both fuses are intact and tight, or that both circuit breakers have not tripped. Replace the fuse or reset the ...
- Is the correct power supply available? Electric dryers require 240-volt power supply. Check with a qualified electrician.
- Was a regular fuse used? Use a time-delay fuse.
- Unusual sounds
- Has the dryer had a period of non-use? If the dryer hasn’t been used for a while, there may be a thumping sound during the first few minutes of operation.
- Is a coin, button, or paper clip caught between the drum and front or rear of the dryer? Check the front and rear edges of the drum for small objects. Clean out pockets before laundering.
- Are the four legs installed, and is the dryer level front to back and side to side? The dryer may vibrate if not properly installed. See the Installation Instructions.
- Is the clothing knotted or balled up? When balled up, the load will bounce, causing the dryer to vibrate. Separate the load items and restart the dryer.
- No heat
- Dryer displaying error message (WET indicator flashing)
- Clothes are not drying satisfactorily, drying times are too long, or load is too hot
- Is the lint screen clogged with lint? Lint screen should be cleaned before each load.
- Has the Air Dry temperature setting been selected? Select the right temperature for the types of garments being dried. See “Additional Features.”
- Is the load too large and heavy to dry quickly? Separate the load to tumble freely.
- Is the exhaust vent or outside exhaust hood clogged with lint, restricting air movement? Run the dryer for 5-10 minutes. Hold your hand under the outside exhaust hood to check air movement. If you do not feel air movement, clean exhaust system of lin...
- Are fabric softener sheets blocking the grille? Use only one fabric softener sheet, and use it only once.
- Is the exhaust vent the correct length? Check that the exhaust vent is not too long or has too many turns. Long venting will increase drying times. See the Installation Instructions.
- Is the exhaust vent diameter the correct size? Use 4" (102 mm) diameter vent material.
- Is the dryer located in a room with temperature below 45ºF (7ºC)? Proper operation of dryer cycles requires temperatures above 45ºF (7ºC).
- Is the dryer located in a closet? Closet doors must have ventilation openings at the top and bottom of the door. The front of the dryer requires a minimum of 1" (25 mm) of airspace, and, for most installations, the rear of the dryer requires 5" (127 ...
- Cycle time too short
- Lint on load
- Stains on load or drum
- Loads are wrinkled
- Odors
- Have you recently been painting, staining, or varnishing in the area where your dryer is located? If so, ventilate the area. When the odors or fumes are gone from the area, rewash and dry the clothing.
- Changing the Automatic Default Settings
- 1. (factory preset dryness level) - WET indicator lit.
- 2. (slightly drier clothes, 15% more drying time) - WET and DAMP indicators lit.
- 3. (much drier clothes, 30% more drying time) - WET, DAMP, and COOL DOWN indicators lit.
- To change the AUTOMATIC default settings:
- 1. Press and hold the TEMP button for at least 6 seconds. The dryer will beep, and the current drying mode will be displayed.
- 2. To select a new drying setting, press the TEMP button again until the desired drying setting is shown. NOTE: While cycling through the settings, the current setting will be lit solid, but the other settings will flash.
- 3. Press the START/PAUSE button to save the drying setting and exit to standby mode. NOTE: To exit without saving, press the POWER button.
- 4. The drying setting you selected will become your new preset drying setting for all AUTOMATIC cycles.
- Changing the Automatic Default Settings
- Have you recently been painting, staining, or varnishing in the area where your dryer is located? If so, ventilate the area. When the odors or fumes are gone from the area, rewash and dry the clothing.
- WHIRLPOOL CORPORATION LAUNDRY WARRANTY
- LIMITED WARRANTY
- ITEMS EXCLUDED FROM WARRANTY
- This limited warranty does not cover:
- 1. Replacement parts or repair labor if this major appliance is used for other than normal, single-family household use or when it is used in a manner that is inconsistent to published user or operator instructions and/or installation instructions.
- 2. Service calls to correct the installation of your major appliance, to instruct you on how to use your major appliance, to replace or repair house fuses, or to correct house wiring or plumbing.
- 3. Service calls to repair or replace appliance light bulbs, air filters or water filters. Consumable parts are excluded from warranty coverage.
- 4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in accordance with electrical or plumbing codes, or use of products not approved by Whirlpool.
- 5. Cosmetic damage, including scratches, dents, chips or other damage to the finish of your major appliance, unless such damage results from defects in materials or workmanship and is reported to Whirlpool within 30 days from the date of purchase.
- 6. Pick up and delivery. This major appliance is intended to be repaired in your home.
- 7. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.
- 8. Expenses for travel and transportation for product service if your major appliance is located in a remote area where service by an authorized Whirlpool servicer is not available.
- 9. The removal and reinstallation of your major appliance if it is installed in an inaccessible location or is not installed in accordance with Whirlpool’s published installation instructions.
- 10. Replacement parts or repair labor on major appliances with original model/serial numbers that have been removed, altered, or cannot be easily determined.
- DISCLAIMER OF IMPLIED WARRANTIES
- LIMITATION OF REMEDIES; EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGES
- YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN. WHIRLPOOL SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and provinces do not allow the exclusion or limitation of incide...
- If outside the 50 United States and Canada, contact your authorized Whirlpool dealer to determine if another warranty applies.
- If you think you need repair service, first see the “Troubleshooting” section of the Use & Care Guide. If you are unable to resolve the problem after checking “Troubleshooting,” additional help can be found by checking the “Assistance or Se...
- sÉcuritÉ de la sÉcheusE
- GUIDE DE DÉMARRAGE RAPIDE/ UTILISATION DE LA SÉCHEUSE
- Pour un résumé sur l'utilisation de la sécheuse après installation, voir le GUIDE DE DÉMARRAGE RAPIDE à la page suivante.
- Programmes
- Programmes automatiques
- Programmes minutés
- Réglages des programmes de séchage minuté
- Air Dry (séchage à l'air)
- Lors de l'utilisation du séchage à l'air :
- Vérifier que les revêtements sont bien cousus.
- Secouer et faire bouffer les oreillers à la main périodiquement pendant le programme.
- Faire sécher l'article complètement. Les oreillers en caoutchouc mousse mettent du temps à sécher.
- Trois brefs signaux sonores retentissent si une combinaison non disponible a été sélectionnée. La dernière sélection ne sera pas acceptée.
- Changer de programme après avoir mis la sécheuse en marche :
- 1. Appuyer sur POWER (mise sous tension). Ceci met fin au programme en cours et arrête la sécheuse.
- 2. Appuyer à nouveau sur le bouton POWER (mise sous tension) ou appuyer sur le bouton de sélection de programme pour mettre la sécheuse en marche.
- 3. Sélectionner le programme et les options désirés.
- 4. Appuyer sans relâcher sur START/PAUSE (mise en marche/ pause). La sécheuse recommence au début du nouveau programme.
- Changer la température de séchage :
- Changer de programme après avoir mis la sécheuse en marche :
- ENTRETIEN DE LA SÉCHEUSE
- Nettoyage de l'emplacement de la sécheuse
- Nettoyage du filtre à charpie
- Ne pas faire fonctionner la sécheuse avec un filtre à charpie déplacé, endommagé, bloqué ou manquant. Une telle action peut causer un échauffement ou des dommages pour la sécheuse et les tissus.
- Si de la charpie tombe dans la sécheuse au moment du retrait du filtre, vérifier le conduit d'évacuation et retirer la charpie. Voir “Exigences concernant l'évacuation”.
- Nettoyage au besoin
- 1. Enlever la charpie du filtre en la roulant avec les doigts.
- 2. Mouiller les deux côtés du filtre à charpie avec de l'eau chaude.
- 3. Mouiller une brosse en nylon avec de l'eau chaude et du détergent liquide; frotter le filtre avec la brosse pour enlever l'accumulation de résidus.
- 4. Rincer le filtre à l'eau chaude.
- 5. Bien sécher le filtre à charpie avec une serviette propre. Replacer le filtre dans la sécheuse.
- Nettoyage de l'intérieur de la sécheuse
- Nettoyage du tambour de la sécheuse :
- 1. Préparer une pâte avec un détergent à lessive en poudre et de l'eau très chaude.
- 2. Appliquer la pâte sur un linge doux. OU Verser un nettoyant liquide domestique ininflammable sur la surface tachée et frotter avec un linge doux jusqu'à ce que toute la teinture et les taches restantes soient enlevées.
- 3. Essuyer complètement le tambour avec un linge humide.
- 4. Faire culbuter une charge de linge ou de serviettes propres pour sécher le tambour.
- Nettoyage du tambour de la sécheuse :
- Retrait de la charpie accumulée
- Précautions à prendre avant les vacances, un entreposage ou un déménagement
- Nettoyage au besoin
- Entretien en cas de non-utilisation ou de remisage
- Précautions à prendre avant un déménagement
- Réinstallation de la sécheuse
- Changement de l'ampoule d'éclairage du tambour
- Changement de l'ampoule du tambour :
- 1. Débrancher la sécheuse ou déconnecter la source de courant électrique.
- 2. Ouvrir la porte de la sécheuse. Trouver le couvercle de l'ampoule d'éclairage sur la paroi arrière de la sécheuse. Enlever la vis située au coin inférieur droit du couvercle. Enlever le couvercle.
- 3. Tourner l'ampoule dans le sens antihoraire. Remplacer l'ampoule seulement par une ampoule de 10 watts pour appareil électroménager. Réinstaller le couvercle et le fixer avec la vis.
- 4. Brancher la sécheuse ou reconnecter la source de courant électrique.
- Changement de l'ampoule du tambour :
- Changement de l'ampoule d'éclairage du tambour
- dépannage
- Essayer d'abord les solutions suggérées ici ce qui vous évitera peut-être le coût d'une visite de service... Pour plus de recommandations, consulter les Instructions d'installation.
- Fonctionnement de la sécheuse
- La sécheuse ne fonctionne pas
- La porte de la sécheuse est-elle bien fermée?
- A-t-on bien enfoncé le bouton START/PAUSE (mise en marche/pause)? Pour les charges importantes, il peut être nécessaire d'appuyer sur le bouton Start/Pause pendant 2 à 5 secondes.
- Un fusible est-il grillé ou un disjoncteur s'est-il déclenché? Il peut y avoir 2 fusibles ou disjoncteurs pour la sécheuse. Vérifier que les deux fusibles sont intacts et serrés ou que les deux disjoncteurs ne sont pas déclenchés. Remplacer l...
- Une alimentation électrique correcte est-elle disponible? Les sécheuses électriques nécessitent une alimentation électrique de 240 V. Vérifier avec un électricien qualifié.
- A-t-on utilisé un fusible ordinaire? Utiliser un fusible temporisé.
- Bruits inhabituels
- La sécheuse est-elle restée hors service pendant un certain temps? Si la sécheuse n'a pas été utilisée depuis quelque temps, il est possible qu'elle émette des bruits saccadés au cours des premières minutes de fonctionnement.
- Une pièce de monnaie, un bouton ou un trombone sont- ils coincés entre le tambour et l'avant ou l'arrière de la sécheuse? Vérifier les bords avant et arrière du tambour pour voir si de petits objets y sont coincés. Vider les poches avant de fa...
- Les quatre pieds sont-ils installés et la sécheuse est-elle d'aplomb de l'avant vers l'arrière et transversalement? La sécheuse peut vibrer si elle n'est pas correctement installée. Voir les Instructions d'installation.
- Les vêtements sont-ils emmêlés ou en boule? Une charge en boule rebondit, ce qui fait vibrer la sécheuse. Séparer les articles de la charge et remettre la sécheuse en marche.
- Absence de chaleur
- La sécheuse affiche un message d'erreur (le témoin WET clignote)
- Le séchage des vêtements n'est pas satisfaisant, les durées de séchage sont trop longues, la charge est trop chaude
- Le filtre à charpie est-il obstrué de charpie? Le filtre à charpie doit être nettoyé avant chaque charge.
- Le réglage de température Air Dry (séchage à l'air) a-t-il été sélectionné? Choisir la température correcte pour les types de vêtements à sécher. Voir “Air Dry (séchage à l'air)”.
- La charge est-elle trop grosse et trop lourde pour sécher rapidement? Séparer la charge pour qu'elle culbute librement.
- Le conduit d'évacuation ou le clapet d'évacuation à l'extérieur est-il obstrué de charpie, restreignant le mouvement de l'air? Faire fonctionner la sécheuse pendant 5 à 10 minutes. Tenir la main sous le clapet d'évacuation à l'extérieur pou...
- Des feuilles d'assouplissant de tissus bloquent-elles la grille de sortie? Utiliser seulement une feuille d'assouplissant par charge et ne l'utiliser qu'une seule fois.
- Le conduit d'évacuation a-t-il la longueur appropriée? Vérifier que le conduit d'évacuation n'est pas trop long ou ne comporte pas trop de changements de direction. Un long conduit augmentera les durées de séchage. Voir les Instructions d'insta...
- Le diamètre du conduit d'évacuation a-t-il la taille correcte? Utiliser un composant de 4" (102 mm) de diamètre.
- La sécheuse se trouve-t-elle dans une pièce où la température ambiante est inférieure à 45ºF (7ºC)? Le bon fonctionnement des programmes de la sécheuse nécessite une température ambiante supérieure à 45°F (7°C).
- La sécheuse est-elle installée dans un placard? Les portes du placard doivent comporter des ouvertures d'aération au sommet et en bas de la porte. Un espace minimum de 1" (25 mm) est nécessaire à l'avant de la sécheuse et, pour la plupart des i...
- Temps de programme trop court
- Charpie sur la charge
- Taches sur la charge ou sur le tambour
- Charges avec faux plis
- Odeurs
- A-t-on récemment employé de la peinture, de la teinture ou du vernis dans la pièce où est installée votre sécheuse? Si tel est le cas, aérer la pièce. Une fois les odeurs ou émanations disparues, laver et sécher à nouveau les vêtements.
- Changement des réglages par défaut de programmes automatiques
- 1. (niveau de séchage préréglé à l'usine) - témoin lumineux WET allumé.
- 2. (vêtements légèrement plus secs, 15 % de temps de séchage supplémentaire) - témoins lumineux WET et DAMP allumés.
- 3. (vêtements beaucoup plus secs, 30 % de temps de séchage supplémentaire) - témoins lumineux WET, DAMP et COOL DOWN allumés.
- Pour modifier les réglages automatiques par défaut :
- 1. Appuyer sur le bouton TEMP (température) pendant au moins 6 secondes. La sécheuse émet un signal sonore, et le mode de séchage en cours s'affiche.
- 2. Pour sélectionner un nouveau réglage de séchage, appuyer de nouveau sur le bouton TEMP jusqu'à ce que le réglage de séchage désiré s'affiche. REMARQUE : Pendant une recherche de réglage, le réglage en cours ne clignote pas mais les autre...
- 3. Appuyer sur le bouton START/PAUSE (mise en marche/pause) pour sauvegarder le réglage de séchage et sortir du mode de veille. REMARQUE : Pour sortir du mode de veille sans sauvegarder, appuyer sur le bouton POWER (mise sous tension).
- 4. Le réglage de séchage que vous avez sélectionné deviendra le nouveau réglage par défaut pour tous les programmes automatiques.
- Changement des réglages par défaut de programmes automatiques
- A-t-on récemment employé de la peinture, de la teinture ou du vernis dans la pièce où est installée votre sécheuse? Si tel est le cas, aérer la pièce. Une fois les odeurs ou émanations disparues, laver et sécher à nouveau les vêtements.
- GARANTIE DES APPAREILS DE BUANDERIE DE WHIRLPOOL CORPORATION
- GARANTIE LIMITÉE
- ÉLÉMENTS EXCLUS DE LA GARANTIE
- La présente garantie limitée ne couvre pas :
- 1. Les pièces de rechange ou la main d'œuvre lorsque ce gros appareil ménager est utilisé à des fins autres que l'usage unifamilial normal ou lorsque les instructions d'installation et/ou les instructions de l'opérateur ou de l'utilisateur four...
- 2. Les visites de service pour rectifier l'installation du gros appareil ménager, montrer à l'utilisateur comment utiliser l'appareil, remplacer ou réparer des fusibles ou rectifier le câblage ou la plomberie du domicile.
- 3. Les visites de service pour réparer ou remplacer les ampoules électriques, les filtres à air ou les filtres à eau de l'appareil. Les pièces consomptibles ne sont pas couvertes par la garantie.
- 4. Les dommages imputables à : accident, modification, usage impropre ou abusif, incendie, inondation, actes de Dieu, installation fautive ou installation non conforme aux codes d'électricité ou de plomberie, ou l'utilisation de produits non appro...
- 5. Les défauts apparents, notamment les éraflures, les bosses, fissures ou tout autre dommage au fini du gros appareil ménager, à moins que ces dommages soient dus à des vices de matériaux ou de fabrication et soient signalés à Whirlpool dans...
- 6. L'enlèvement et la livraison. Ce gros appareil ménager est conçu pour être réparé à domicile.
- 7. Les réparations aux pièces ou systèmes résultant d'une modification non autorisée faite à l'appareil.
- 8. Les frais de déplacement et de transport pour le service d'un produit si votre gros appareil ménager est situé dans une région éloignée où un service d'entretien Whirlpool autorisé n'est pas disponible.
- 9. La dépose et la réinstallation de votre gros appareil ménager si celui-ci est installé dans un endroit inaccessible ou n'est pas installé conformément aux instructions d'installation fournies par Whirlpool.
- 10. Les pièces de rechange ou la main-d'oeuvre pour les gros appareils ménagers dont les numéros de série et de modèle originaux ont été enlevés, modifiés ou qui ne peuvent pas être facilement identifiés.
- CLAUSE D'EXONÉRATION DE RESPONSABILITÉ AU TITRE DES GARANTIES IMPLICITES
- LIMITATION DES RECOURS, EXCLUSION DES DOMMAGES FORTUITS OU INDIRECTS
- LE SEUL ET EXCLUSIF RECOURS DU CLIENT DANS LE CADRE DE LA PRÉSENTE GARANTIE LIMITÉE CONSISTE EN LA RÉPARATION PRÉVUE CI-DESSUS. WHIRLPOOL N'ASSUME AUCUNE RESPONSABILITÉ POUR LES DOMMAGES FORTUITS OU INDIRECTS. Certains États et certaines provin...
- Si vous résidez à l'extérieur du Canada et des 50 États des États-Unis, contactez votre marchand Whirlpool autorisé pour déterminer si une autre garantie s'applique.
- Si vous avez besoin d'un service de réparation, voir d'abord la section “Dépannage” du Guide d'utilisation et d'entretien. Si vous n'êtes pas en mesure de résoudre le problème après avoir consulté la section “Dépannage”, vous pouvez t...
-
-
-
-
-
Document Outline
- dryer venting specifications
- dryer Safety
- installation requirements
- WARNING: To reduce the risk of fire, this dryer MUST BE EXHAUSTED OUTDOORS.
- NOTE: This guide is intended to aid licensed HVAC or Architectural Engineers who design single and multi-dryer unit venting systems for Whirlpool Corporation dryers sold in the United States. Whirlpool Corporation provides required airflow and back p...
- Outside Exhaust
- The four basic reasons for exhausting a dryer outdoors are detailed in this section:
- The following codes should be reviewed to ensure dryer vent systems are in compliance:
- There are other codes requiring dryers to be exhausted when installed in confined spaces where specified clearances from combustible surfaces cannot be met. See the Installation Instructions for the specific dryer model being used or considered for s...
- Local codes and ordinances that exist must also be met. Consult your local building inspector for more information.
- A normal towel load contains some residual water when it is removed from the washer. The dryer must remove this water and discharge it from the drum. When the dryer is not exhausted outside, this moist air will be recirculated through the dryer, redu...
- Exhausting moisture into the room can also cause damage to walls, floors, picture hangers, and cause condensation on windows and walls in cold weather.
- Even though the dryer is equipped with a lint screen, fine particles of lint will pass through the screen and be exhausted out of the dryer. Proper venting of the dryer will keep lint from accumulating in the laundry area.
- In order to remove moisture from the garments in the dryer, heat is generated to vaporize the water. Exhausting the dryer outdoors removes excess heat from the laundry area of the building.
- Central Exhaust System Requirements
- Exhaust individual dryers to the central exhaust duct system with proper size vents to assure adequate performance of each dryer. The dryer has 4" (102 mm) exhaust duct connections. Connect each dryer to the central vent with a 4" (102 mm) diameter a...
- Install weighted dampers on each individual dryer exhaust duct. These dampers may be used for balancing out the overall duct system.
- Design the central duct system for sufficient capacity to handle the maximum number of dryers operated at one time.
- Consider moisture, lint and air temperature in the design of the central duct system. Maximum exhaust temperature of the dryer will not exceed 200°F (93.3°C) when the dryer is operated according to the instructions provided with the dryer.
- Provide for periodic inspection and clean-out of lint accumulated in the central duct system.
- The capacity to handle up to 230 CFM (cubic feet per minute) of air flow for each dryer in the system.
- A minimum back pressure of -0.1" (-2.5 mm) water column (vacuum) when measured at the connection to the dryer.
- Provide maximum back pressure, based on the maximum rated vent length shown in the Installation Instructions included with dryer. Maximum Allowable Back Pressure chart lists maximum rated vent length and back pressure.
- The minimum duct air velocity during normal operating conditions should be at least 1,200 FPM (feet per minute) to keep lint moving through the vent. (In a 4" (102 mm) diameter pipe, this requires at least 105 CFM of air flow.)
- Measuring and Verifying Actual System Back Pressure
- Back pressure should be measured with an empty dryer, a clean lint screen and with the dryer operating in the Air Only cycle (no heat). Use an inclined manometer, such as Dwyer model 102 (0"-2" [0 mm - 51 mm] range) or Dwyer model 172 (0"-1" [0 mm - ...
- Maximum Allowable Back Pressure for Dryer
- Maximum Rated Vent Length without 90° Elbows (determined from product literature)
- Maximum Allowable Back pressure at connection to dryer (no clothes loaded and clean lint screen)
- 36-37 ft
- 0.40" Water Column
- 64 ft
- 0.60" Water Column
- 100 ft
- 0.80" Water Column
- 120 ft
- 1.00" Water Column
- 130 ft
- 1.10" Water Column
- Back pressure should be measured with an empty dryer, a clean lint screen and with the dryer operating in the Air Only cycle (no heat). Use an inclined manometer, such as Dwyer model 102 (0"-2" [0 mm - 51 mm] range) or Dwyer model 172 (0"-1" [0 mm - ...
- Single Dryer Venting Systems
- Single dryer venting systems are defined as systems that have only one dryer unit attached to a residential-type 4" (102 mm) diameter rigid metal vent system. For single dryer venting systems, see the Installation Instructions for the specific dryer ...
- In cases in which the Installation Instructions do not address the vent length for the specific number of elbows required for a particular application, the following calculations may be used. (The total vent system length includes all straight and cu...
- Measuring and Verifying Actual System Back Pressure
- For 90° elbows, reduce the allowable vent system length by 10 ft (3.05 m).
- For 45° elbows, reduce the allowable vent system length by 6 ft (1.83 m).
- For example, if the Installation Instructions state that a dryer is allowed 40 ft (12.2 m) of total vent length with two 90° bends, and the installation requires three 90° bends, the total allowable vent length would be reduced by 10 ft (3.0 m) (fr...
- The airflow of a dryer depends on the design of the exhaust vent. Each dryer model has a maximum rated vent length, shown in the product literature that is supplied with each model, or on the Whirlpool.com website. The exhaust airflow of any Whirlpoo...
- All Whirlpool electric dryer models, including “long vent dryers,” Turbo Vent™ dryers and combo washer/dryer units that are sold in the United States and Canada are UL listed (reference UL 2158 standard), and all Whirlpool gas dryer models are ...
- Closets used for dryer installation must provide multiple openings to allow air to flow through the dryer and around the dryer to dissipate heat. Any dryer enclosure or room that does not have an inlet and outlet for an operating forced air HVAC syst...
- *Required spacing
- The dimensions shown are for the minimum spacing allowed.
- Additional spacing should be considered for ease of installation and servicing.
- Additional clearances might be required for wall, door, and floor moldings.
- Additional spacing of 1" (25 mm) on all sides of the dryer is recommended to reduce noise transfer.
- For closet installation, with a door, minimum ventilation openings near the top and bottom of the door are required. Louvered doors with equivalent ventilation openings are acceptable.
- Companion appliance spacing should also be considered.
- *Recommended spacing.
- Certain electronic dryer models have airflow detection capabilities. (See specific model product literature for details). If the airflow in the dryer is extremely low, an “AF” code will be displayed on the control panel. For single dryer venting ...
- For multi-dryer venting systems, the “AF” code means that your vent may be blocked or partially blocked or that the venting system is creating back pressure in excess of the maximum allowed. In this case, the engineering firm that designed the sy...
- Multiple Dryer Venting Systems
- Multiple dryer venting systems must be designed specifically for each application.
- NOTE: It is recommended that an architectural or HVAC engineering firm be consulted for designing the dryer venting system.
- Connecting a number of dryers to a single vent system is common in coin-laundry stores and in many apartment buildings. Listed here are some requirements for examples of three different multiple dryer venting systems.
- The most common is the horizontal system, in which banks of dryers are all located in one room and vented through a common duct. See the following illustration for an example of a generic horizontal system.
- The vertical system is used in some apartment buildings that have a washer and dryer on each floor. Each dryer is exhausted into the same central vertical duct. See the following illustration for an example of a generic vertical system.
- The combination system may be used in high-rise apartments, with a bank of dryers installed at several different levels. Each of these banks then exhausts into a central vertical vent. See the following illustration for an example of a combination sy...
- Dryer inspection and cleaning
- Frequency of Exhaust System Cleaning
- Every exhaust system must be inspected periodically and cleaned to ensure that it is intact and free from lint accumulation. The frequency of these inspections will vary, depending on the system and usage of the dryer. For single-family usage, an ann...
- Inspecting the Exhaust System
- 1. Disconnect the exhaust duct from the dryer and from the exhaust hood (at the exhaust outlet) outside of the building.
- 2. Inspect the interior of the duct and remove any lint accumulation.
- 3. Reassemble the exhaust duct and hood, checking that the joints are secure.
- 4. Operate the dryer and verify that the exhaust air is not obstructed in the vent and that there are no leaks in the system.
- ® Registered Trademark/TM Trademark of Whirlpool, U.S.A.
- Inspecting the Exhaust System
Related Models for Whirlpool Clothes Dryer WED9151YW
- Whirlpool 1W10287573A
- Whirlpool 240-volt
- Whirlpool 240-VOLT ELECTRIC DRYER
- Whirlpool 3390148
- Whirlpool 3393 137
- Whirlpool 3395339
- Whirlpool 3396304
- Whirlpool 3397617
- Whirlpool 3397627C
Whirlpool Popular Categories
Appliances
Air Conditioners
Microwaves
Washers
Refrigerators
Ovens
Hoods
Kitchen Machines
Cooktop
Telephone
Routers
Door
More Whirlpool Manuals