HP HP 34970A Manuals
HP Switch HP 34970A manuals download on ManualAgent: User's Manual
-
Document Outline
- Contents
- Title Page
- HP 34970A Overview
- In This Book
- Chapter 1: Quick Start
- To Prepare the Instrument for Use
- Installing HP BenchLink Data Logger Software
- To Connect Wiring to a Module
- To Set the Time and Date
- To Configure a Channel for Scanning
- To Copy a Channel Configuration
- To Close a Channel
- If the Instrument Does Not Turn On
- To Replace the Power-Line Fuse
- To Adjust the Carrying Handle
- To Rack Mount the Instrument
- Chapter 2: Front-Panel Overview
- Front-Panel Menu Reference
- To Monitor a Single Channel
- To Set a Scan Interval
- To Apply Mx+B Scaling to Measurements
- To Configure Alarm Limits
- To Read a Digital Input Port
- To Write to a Digital Output Port
- To Read the Totalizer Count
- To Output a DC Voltage
- To Configure the Remote Interface
- To Store the Instrument State
- Chapter 3: System Overview
- Chapter 4: Features and Functions
- SCPI Language Conventions
- Scanning
- Single-Channel Monitoring
- Scanning With External Instruments
- General Measurement Configuration
- Temperature Measurement Configuration
- Voltage Measurement Configuration
- Resistance Measurement Configuration
- Current Measurement Configuration
- Frequency Measurement Configuration
- Mx+B Scaling
- Alarm Limits
- Digital Input Operations
- Totalizer Operations
- Digital Output Operations
- DAC Output Operations
- System-Related Operations
- Remote Interface Configuration
- Calibration Overview
- Factory Reset State
- Instrument Preset State
- Multiplexer Module Default Settings
- Module Overview
- Chapter 5: Remote Interface Reference
- SCPI Command Summary
- Rules for Using a Channel List
- Rules for Using scan_list and ch_list Parameters
- Scan Measurement Commands
- Monitor Commands
- Scan Configuration Commands
- Scan Statistics Commands
- Scan Memory Commands
- Scanning With an External Instrument
- Temperature Configuration Commands
- Voltage Configuration Commands
- Resistance Configuration Commands
- Current Configuration Commands
- Frequency and Period Configuration Commands
- Mx+B Scaling Commands
- Alarm Limit Commands
- Digital Input Commands
- Totalizer Commands
- Digital Output Commands
- DAC Output Commands
- Switch Control Commands
- Scan Triggering Commands
- State Storage Commands
- System-Related Commands
- Interface Configuration Commands
- Status System Commands
- Calibration Commands
- Service-Related Commands
- IEEE 488.2 Common Commands
- Simplified Programming Overview
- The MEASure? and CONFigure Commands
- Setting the Function, Range, and Resolution
- Temperature Configuration Commands
- Voltage Configuration Commands
- Resistance Configuration Commands
- Current Configuration Commands
- Frequency Configuration Commands
- Scanning Overview
- Single-Channel Monitoring Overview
- Scanning With an External Instrument
- Mx+B Scaling Overview
- Alarm System Overview
- Digital Input Commands
- Totalizer Commands
- Digital Output Commands
- DAC Output Commands
- Switch Control Commands
- State Storage Commands
- System-Related Commands
- Interface Configuration Commands
- RS-232 Interface Configuration
- Modem Communications
- The SCPI Status System
- What is a Condition Register?
- What is an Event Register?
- What is an Enable Register?
- HP 34970A Status System
- The Status Byte Register
- Using Service Request (SRQ) and Serial Poll
- Using *STB? to Read the Status Byte
- Using the Message Available Bit (MAV)
- To Interrupt Your Bus Controller Using SRQ
- To Determine When a Command Sequence is Completed
- The Questionable Data Register
- The Standard Event Register
- The Alarm Register
- The Standard Operation Register
- Status System Commands
- Calibration Commands
- Service-Related Commands
- An Introduction to the SCPI Language
- Using Device Clear
- SCPI Command Summary
- Chapter 6: Error Messages
- Chapter 7: Application Programs
- Chapter 8: Tutorial
- System Cabling and Connections
- Measurement Fundamentals
- The Internal DMM
- Temperature Measurements
- Sources of Error in Thermocouple Measurements
- DC Voltage Measurements
- Sources of Error in DC Voltage Measurements
- AC Voltage Measurements
- Sources of Error in AC Voltage Measurements
- Current Measurements
- Sources of Error in DC Current Measurements
- Sources of Error in AC Current Measurements
- Resistance Measurements
- Sources of Error in Resistance Measurements
- Strain Gage Measurements
- Frequency and Period Measurements
- Low-Level Signal Multiplexing and Switching
- Actuators and General-Purpose Switching
- Matrix Switching
- RF Signal Multiplexing
- Multifunction Module
- Relay Life and Preventative Maintenance
- Chapter 9: Specifications
- DC, Resistance, and Temperature Accuracy Specifications
- DC Measurement and Operating Characteristics
- AC Accuracy Specifications
- AC Measurement and Operating Characteristics
- Measurement Rates and System Characteristics
- Module Specifications
- Typical AC Performance Graphs
- Software Specifications
- Product and Module Dimensions
- To Calculate Total Measurement Error
- Interpreting Internal DMM Specifications
- Configuring for Highest Accuracy Measurements
- Declaration of Conformity
- Warranty Information
- Index
Related Models for HP Switch HP 34970A
- HP 1410-16G
- HP 1700-24
- HP 1920-16G Switch
- HP 1920-24G Switch
- HP 1920-24G-PoE+ (180W) Switch
- HP 1920-24G-PoE+ (370W) Switch
- HP 1920-48G Switch
- HP 1920-8G Switch
- HP 1920-8G-PoE+ (180W) Switch
HP Popular Categories
Headphones
Cameras
Televisions
Air Conditioners
Mobile Phones
Desktops
Laptops
Projectors
Servers
Tablets
Calculators
Printers
Accessories
Lawn Mowers
GPS
Refrigerators
Ovens
Modems
Adapters
Vacuum Cleaners
Musical Instruments
Storage
Fans
Stud Sensor
Monitors
Bicycles
Cooktop
Saw
Fax Machine
Telephone
Routers
Speakers
Desktop PCs
More HP Manuals