Meiko K-200 Owner's Manual | Page 9
Page 9
C O N T R O L
C O N T R O
C O N T R
controlled
SECTION 3 - INSTALLATION
3.6 Vent Connection
IMPORTANT
In some cases, local codes dictate that
ventilation connections be made only by a
certified HVAC professional.
CAUTION
All aspects of the ventilation system must be
corrosion-resistant, frost-free and protected
against freezing temperatures (32°F/0°C or
lower). Freezing temperatures inhibit proper
operation and can damage internal
components.
Meiko K-Tronic series warewashers are
designed for use with a single-point, indirect
ventilation connection. The machine includes
a powered vent that is adequate for short,
vertical runs (10’/3m or less). For longer runs,
it is necessary to provide a powered fan for
the system (for instance, mounted on the roof)
to provide adequate airflow.
CFM ratings for the vent system, as well as
construction details, are provided on the
engineering drawings supplied with the
machine. At the time of installation, the vent
should be in place.
1. Check that the exhaust vent is correctly
positioned above the machine’s fan. See
Figure 3-6. Note that the vent should NOT
be connected directly to the machine so
that room air can be drawn into the vent.
2. If the exhaust vent is powered, check the
airflow using an airflow meter/
anemometer. The CFM rating of the vent
should match the CFM rating specified on
the factory-supplied engineering drawings.
3. If the vent is constructed according to the
engineering drawings, it will include a
1”(25mm)-wide “gutter” along the bottom
edge to collect condensation. If desired,
this condensation can be drained directly
through the top panel of the machine at
the location shown in Figure 3-6.
A 1/4” dia. stainless steel tube is recom-
mended for this purpose. Note that the
drainage tube should be installed on the
side of the vent AWAY from the control
panel as shown in Figure 3-6.
After installation, the seams between the
tube, vent and machine should be sealed
with silicone sealant.
Figure 3-6: Vent connection
Condensation
channel
Gap permits
room air to
enter vent
Condensation
drain tube (if
used - supplied
by customer)
installed on side
of vent AWAY
from control
panel
Silicone
sealant
Control
panel
Related Manuals for Meiko K-200
-
Asko Dishwasher D3100 Use & Care Manual
36 pages
-
Baumatic Dishwasher BDW45.1 User's Manual
48 pages
-
Bosch Dishwasher SMV50C00GB Instruction Manual
28 pages
-
Diplomat Dishwasher ADP8352 User's Manual
10 pages
-
Electrolux Dishwasher ESF 63020 User's Manual
40 pages
-
Electrolux Dishwasher Diva Service Manual
32 pages
-
Fisher & Paykel Dishwasher DishDrawer DD603 I Service Manual
47 pages
-
Miele Dishwasher G 646 SC Operation Manual
68 pages
-
NEFF Dishwasher S5443X2GB Operation Manual
27 pages
-
Technika Dishwasher TBD4SS-2 User's Manual
6 pages
-
Whirlpool Dishwasher Whirlpool Dishwasher ADP6000IX User's Manual
13 pages
-
Hotpoint Dishwasher EXPERIENCE DISHWASHER FDFET 33121 User's Manual
20 pages
-
Westinghouse Dishwasher WSF6602 User's Manual
24 pages
-
DEFY Dishwasher DDW 157 User's Manual
18 pages
-
Fisher & Paykel Dishwasher 918TD User's Manual
21 pages
-
Maytag Dishwasher MDB4949SDM Installation Guide
76 pages
-
Maytag Dishwasher MDB4949SDM Use & Care Manual
42 pages
-
Maytag Dishwasher MDB5969SDM Use & Care Manual
42 pages
-
Maytag Dishwasher MDB8969SDM Use & Care Manual
42 pages
-
Miele Dishwasher G 6165 SCVi Futura Crystal Operating and Installation Instructions
80 pages
-
Miele Dishwasher G 6165 SCVi Futura Crystal Specification Sheet
5 pages
-
Miele Dishwasher G 6365 SCVi Specification Sheet
5 pages
-
Miele Dishwasher G 6560 SCVi Specification Sheet
5 pages
-
Frigidaire Dishwasher FFBD2406NS Installation Instructions
2 pages