Marshall MG50FX User's Manual | Page 3

Marshall Musical Instrument Amplifier User's Manual - MG50FX.
Download
Page  of 7
4.1, 2017 votes
background image

3

2

Restoring Settings - WARNING ALL AMP &

FOOTCONTROLLER SETTINGS WILL BE LOST

To restore the unit to factory settings (see handbook

rear cover) you must hold the Store switch (12) while

powering on the unit. The Clean/Crunch (3) and OD (5)

lights will light orange. You can then release the Store

switch (12).
Resetting the amplifier will erase all user Channel

presets and all user Footcontroller settings, replacing

them with the factory presets.

Channel Selection

The amplifier has 4 channels - Clean, Crunch, OD1 &

OD2.
Pressing the Clean/Crunch switch (3) selects between

the Clean (Green Light) and Crunch (Red Light)

channels.
Pressing the OD switch (5) selects between the OD1

(Green Light) and OD2 (Red Light) channels.
When moving from an OD channel to a Clean/Crunch

channel, the unit remembers the last channel you were

in before leaving. E.g. If you have moved from the

Crunch Channel to an OD channel and you press the

Clean/Crunch switch (3), the amplifier will revert back to

the Crunch channel - rather than starting again in the

Clean channel.
Modes

The amplifier operates in two modes - Preset and

Manual.
To change between these two modes, you must hold

the Tap switch (10) down for at least two seconds.

When in manual mode the Store switch (12) lights red

and the selected channel light (3 or 5) will start to flash.
The amplifier will remember the last mode it was in after

power off and revert to it the next time it is powered on.
Preset

This is the factory default operation of the amplifier.
In Preset mode the position of all controls except

Master Volume (13) are stored within each channel.

Each channel should be considered a preset.
Selecting a channel automatically recalls the settings

stored within the channel. Note: The physical position of

the front panel controls, except Master Volume (13)

which is not storable, will now not match the actual

settings of the amplifier. All front panel switches will

automatically update.
Altering a control will cause the associated parameter to

jump to the current physical position of that control.
When a control is altered the selected channel light (3

or 5) will start to flash indicating that the current preset

has been altered.
To store the updated settings, push the Store switch

(12).
If you select another channel without pressing Store

(12) then any altered settings will be lost as the new

channel and its settings are recalled.
Manual

In manual mode the amp’s settings always match the

physical positions of the controls.
Changing channel only changes the channel, NO

presets are recalled, NO other controls are altered.
Pressing Store (12) will store the current settings into

the selected channel. These can then be recalled when

using the unit in Preset mode.

When channel settings have been stored the current

channel light (3 or 5) will stop flashing indicating the

preset has been saved.
Reverb & FX

The amplifier provides two simultaneous effects,

Reverb and one of four FXs (Chorus, Phaser, Flanger

or Delay)
Reverb

The Reverb control (8) sets the amount of signal sent to

the reverb section - allowing the reverb to spill between

channels as different presets are recalled. When the

Reverb control (8) is set to ‘0’ the reverb is switched off,

the status of the reverb is also indicated on the optional

footcontroller.
FX

The FX control is split into four segments and selects

the type of FX and adjusts its associated settings.

When the FX control is set to ‘0’ the FX are switched

off, the status of the FX is also indicated on the optional

footcontroller.

Tap Tempo

The Tap Tempo switch (10) is used for the Delay effect

only.
The Tap Tempo switch matches the delay time to the

time between two presses.
The Tap Tempo LED flashes red at the

selected/recalled delay time.
The number of repeats is reduced as the delay time

decreases.
If you change from a channel with delay to one without

delay the effect will spill between channels.
If you change from a channel with delay to a channel

with delay set to a different delay time the delay effect

will not spill between channels.
MP3 / Line In

The 3.5mm MP3 / Line In socket (14) allows the

connection of an external audio source e.g. MP3 or CD

player.
Headphones

The 3.5mm Headphones socket (16) allows the

connection of a pair of headphones. When a jack is

inserted into the headphones socket the unit’s speaker

is muted.
Power

The Power switch (17) turns the amplifier on and off. If

current settings have not been stored they will be lost.

MG15FX & MG30FX Overview

0

Chorus
Phaser
Flanger
Delay

FX Off

Speed increases and depth is reduced as

knob is turned clockwise.

Speed increases as knob is turned

clockwise.

Speed increases, feedback and depth are

reduced as knob is turned clockwise.

Delay level is increased as knob turned

clockwise.

Power (RMS)

15W

Channels

4

Speaker

1x8"

Weight (kg)

7.7kg

Size (mm) W, H, D

382 x379 x205

MG15FX Technical Specification

Power (RMS)

30W

Channels

4

Speaker

1x10"

Weight (kg)

10.8kg

Size (mm) W, H, D

480 x420 x225

MG30FX Technical Specification

E
N

G

L
I

S
H

* EUROPE ONLY

- Note: This equipment has been tested and found to comply with the requirements of the EMC Directive

(Environments E1, E2 and E3 EN 55103-1/2) and the Low Voltage Directive in the E.U.
* EUROPE ONLY - Note: The Peak Inrush current for the MG15FX is 2.5 amps.

The Peak Inrush current for the MG30FX is 5 amps.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates,

uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try

to correct the interference by one or more of the following measures:

* Reorient or relocate the receiving antenna.

* Increase the separation between the equipment and the receiver.

* Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

* Consult the dealer or an experienced radio/TV technician for help.

Follow all instructions and heed all warnings

KEEP THESE INSTRUCTIONS !

Related Manuals for Marshall MG50FX

0.618892s