Marshall MG100FX Owner's Manual | Page 6

Marshall Musical Instrument Amplifier Owner's Manual - MG100FX.
Download
Page  of 7
4.4, 1191 votes
background image

9

8

Footcontrol er (optional-PEDL-90008)

Footcontrol er Factory Settings

Footswitch 1: Clean : Crunch Switch

Footswitch 2: Overdrive Switch

Footswitch 3: Tap Tempo Switch

Footswitch 4: Tuner
Programming

The footswitch can be programmed to store front panel

switches (Switch Store) or complete presets (Preset

Store).
Switch Store

To assign a front panel switch to a Footswitch (1),

press and hold the front panel switch and while held

down press the Footswitch (1) you wish to assign it to.

The Digital Display (3) will swirl to show that the

footswitch has been assigned. You can then release the

footswitch and front panel switch.
Preset Store

To assign a preset to a Footswitch (1), select the

required channel and modify the front panel controls if

required, press and hold the Store switch on the front

panel and while held down, press your chosen

Footswitch (1).
The Digital Display (3) will swirl to show that the

footswitch has been assigned. You can then release the

footswitch and Store switch.
Footcontroller Presets are independent of the dedicated

Channel presets stored within the amplifier. This allows

you to create a number of presets based on the same

channel/pre-amp setting.

When either a Channel preset or Footswitch preset has

been altered the Digital Display (3) will begin to flash.

The footcontroller will flash the relevant number if a

Footswitch preset has been altered or will flash a “-“ if a

Channel preset has been altered.
Pressing only the Store switch at this point will overwrite

the altered Channel or Footswitch preset.
To store an altered Channel preset to the

Footswitch instead, hold the Store switch and while

held down, press your chosen Footswitch (1) - Just like

a normal Preset Store.
To store an altered Footswitch Preset to another

Footswitch hold the Store switch and while held down,

press your chosen Footswitch (1) - Just like a normal

Preset Store.
Digital Display

When recalling a footswitch preset, the Digital Display

(3) will indicate which footswitch number has been

pressed.
If a Channel preset has been recalled the Digital

Display (3) will remain blank.
When either a Channel preset or Footswitch preset has

been altered the Digital Display (3) will begin to flash.

The footswitch will flash the relevant number if a

Footswitch preset has been altered or will flash a “-“ if a

Channel preset has been altered.
Tuner

The Tuner can be accessed in two ways:
MG15FX & MG30FX

By simultaneously pushing the Tap (10) and Store (12)

switches on the front panel or by assigning the Tuner to

the footswitch. Note: On factory reset / first switch on,

the Tuner is already assigned to Footswitch number 4.
Assigning the Tuner to a footswitch is carried out like

any other Switch Store. To assign the Tuner to the

footswitch hold down the Tap (10) and Store (12)

switches and press the chosen footswitch you wish to

assign it to. The Digital Display (3) will swirl to show that

the footswitch has been assigned. You can then release

the footswitch and front panel switch.
MG50FX & MG100FX

By simultaneously pushing the Damping (17) and Store

(19) switches on the front panel or by assigning the

Tuner to the footswitch. Note: On factory reset / first

switch on, the Tuner is already assigned to Footswitch

number 4.
Assigning the Tuner to a footswitch is carried out like

any other Switch Store. To assign the Tuner to the

footswitch hold down the Damping (17) and Store (19)

switches and press the chosen footswitch you wish to

assign it to. The Digital Display (3) will swirl to show that

the footswitch has been assigned. You can then release

the footswitch and front panel switch.

For all amplifiers, when entering Tuner mode the unit

mutes and Clean : Crunch (3) and OD (5) switches light

yellow.
The Digital Display (3) indicates the closest current note

being played. The indicator dot on the lower right hand

corner shows if the current closest note is #.
The LED Status Panel (2) is used to show how far away

from the closest note the current note being played is.

When the central FX Status LED lights, it indicates the

correct tuning, with the others progressively indicating

the tuning is up to 50 cents up or down.
To exit the Tuner push any footswitch, the amplifier will

then exit returning to the settings before entering.

1

3

2

1. Footswitches

Each footswitch can be assigned a different stored function.
2. LED Status Panel

This always reflects the current status of the amplifier or tuner details:
CLN & OD: Current Channel

REV: Reverb On/Off

FX: FX Section On / Off

Ext FX: External FX Loop On/Off (MG50FX & MG100FX)

Damp: Damping Mode (MG50FX & MG100FX)

Tap: Tap Tempo speed.
3. Digital Display

This display indicates the various functions of the footcontroller.

E
N

G

L
I

S
H

 

Also See for Marshall MG100FX

Related Manuals for Marshall MG100FX

0.561241s