Marshall MG100FX Owner's Manual | Page 5

Marshall Musical Instrument Amplifier Owner's Manual - MG100FX.
Download
Page  of 7
4.4, 1191 votes
background image

Channel Selection

The amplifier has 4 channels - Clean, Crunch, OD1 &

OD2.
Pressing the Clean/Crunch switch (3) selects between

the Clean (Green Light) and Crunch (Red Light)

channels.
Pressing the OD switch (5) selects between the OD1

(Green Light) and OD2 (Red Light) channels.
When moving from an OD channel to a Clean/Crunch

channel, the unit remembers the last channel you were

in before leaving. E.g. If you have moved from the

Crunch Channel to an OD channel and you press the

Clean/Crunch switch (3), the amplifier will revert back to

the Crunch channel - rather than starting again in the

Clean channel.
Modes

The amplifier operates in two modes - Preset and

Manual.
To change between these two modes, you must hold

the Damping switch (17) down for at least two seconds.

When in manual mode the Store switch (19) lights red

and the selected channel light (3 or 5) will start to flash.
The amplifier will remember the last mode it was in after

power off and revert to it the next time it is powered on.
Preset

This is the factory default operation of the amplifier.
In Preset mode the position of all controls except

Master Volume (16) are stored within each channel.

Each channel should be considered a preset.
Selecting a channel automatically recalls the settings

stored within the channel. Note: The physical position of

the front panel controls, except Master Volume (16)

which is not storable, will now not match the actual

settings of the unit. All front panel switches will

automatically update.
Altering a control will cause the associated parameter to

jump to the current physical position of that control.
When a control is altered the selected channel light (3

or 5) will start to flash indicating that the current preset

has been altered.
To store the updated settings, push the Store switch

(19).
If you select another channel without pressing Store

(19) then any altered settings will be lost as the new

channel and its settings are recalled.
Manual

In manual mode the amps settings always match the

physical positions of the controls.
Changing channel only changes the channel, NO

presets are recalled, NO other controls are altered.
Pressing Store (19) will store the current settings into

the selected channel. These can then be recalled when

using the unit in Preset mode.

When channel settings have been stored the current

channel light (3 or 5) will stop flashing indicating the

preset has been saved.
Reverb & FX

The amplifier provides three simultaneous effects,

Reverb, Delay and one of three Modulation effects

(Chorus, Phaser, or Flanger).
Reverb

The Reverb control sets the amount of signal sent to

the reverb section - allowing the reverb to spill between

channels as different presets are recalled. The Rev

switch (8) switches the reverb effect on and off, the

status of the reverb is also indicated on the

footcontroller.
FX

The FX section consists of two effects, Delay and

Modulation. The FX section can be globally turned on

and off via the FX switch (11).
Delay

The Delay control (14) sets the amount of signal sent to

the delay section. When the Delay control (14) is set to

‘0’ the delay is switched off.
Modulation

The Mod control (12) is split into three segments and

selects the type of modulation effects and adjusts its

associated settings. When the Mod control (12) is set to

‘0’ the modulation effects are switched off.

Tap Tempo

The Tap Tempo switch (13) is used for the Delay effect

only.
The Tap Tempo switch matches the delay time to the

time between two presses.
The Tap Tempo LED flashes red at the

selected/recalled delay time.
The number of repeats is reduced as the delay time

decreases.
If you change from a channel with delay to one without

delay the effect will spill between channels.
If you change from a channel with delay to a channel

with delay set to a different delay time the delay effect

will not spill between channels.
MP3 / Line In

The 3.5mm MP3 / Line In socket (24) on the rear panel

allows the connection of an external audio source e.g.

MP3 or CD player.

7

6

Headphones & Line Out

The 3.5mm Headphones socket (18) allows the

connection of a pair of headphones. When a jack is

inserted into the headphones socket the unit’s speaker

is muted.
Additionally the Headphones socket (18) can also be

used as a Line Out to send the signal to an external

equipment e.g. A computer, digital recorder or mixer.

When a jack is inserted into the socket the unit’s

speaker is muted providing ‘silent recording’. The unit’s

output can then be monitored directly from the external

equipment used.
Damping

The Damping switch (17) selects between the two

modes of power amp damping. When Damping is off

(LED off), the power amp response resembles the feel

of a classic power amp with emphasized middle and

limited bass and treble. Switching Damping on (LED on)

will boost the speaker resonances both in the bass and

high frequency ranges.
FX Loop

The FX Return socket (25) on the rear panel is used to

connect the OUTPUT of the effects processor or pedal

you are using in the effects loop.
The FX loop is series and set at instrument level so

both guitar FX or professional units can be connected.
The FX Send socket (26) on the rear panel is used to

connect to the INPUT of the unit you are using in the

effects loop.
The FX loop is switched on and off via the Ext FX

switch (15) on the front panel.

Loudspeaker

ALWAYS USE A NON-SCREENED MARSHALL

APPROVED SPEAKER LEAD WHEN CONNECTING

AN EXTENSION CABINET TO THESE AMPLIFIERS.
MG50FX

The single Loudspeaker socket (22) is used to connect

either the internal speaker or an external speaker

cabinet to the unit’s power amp. When using external

cabinets ensure the total load impedance is equal to, or

exceeds, 8 ohms.
MG100FX 1x12" & 2x12" Combos

The single Loudspeaker socket (22) is used to connect

either the internal speaker or an external speaker

cabinet to the unit’s power amp. When using external

cabinets ensure the total load impedance is equal to, or

exceeds, 4 ohms.
MG100HFX Head

The two Loudspeaker sockets are used to connect to 1

or 2 external cabinets. When using external cabinets

ensure the total load impedance is equal to, or exceeds,

4 ohms.
Power

The Power switch (20) turns the amplifier on and off. If

current settings have not been stored they will be lost.
Restoring Settings - WARNING: ALL AMP &

FOOTSWITCH SETTINGS WILL BE LOST

To restore the unit to factory settings (see handbook

rear cover) you must hold the Store switch (19) while

powering on the amplifier. The Clean/Crunch (3) and

OD (5) lights will light orange. You can then release the

Store switch (19).
Resetting the amplifier will erase all user Channel

presets and all user Footcontroller settings, replacing

them with the factory presets.

0

Chorus
Phaser
Flanger

Modulation Off

Speed increases and depth is reduced as

knob is turned clockwise.

Speed increases as knob is turned

clockwise.

Speed increases, feedback and depth are

reduced as knob is turned clockwise.

MG50FX & MG100FX / MG100HFX Overview

E
N

G

L
I

S
H

* EUROPE ONLY

- Note: This equipment has been tested and found to comply with the requirements of the EMC Directive

(Environments E1, E2 and E3 EN 55103-1/2) and the Low Voltage Directive in the E.U.
* EUROPE ONLY - Note: The Peak Inrush current for the MG50FX is 9.6 amps.

The Peak Inrush current for the MG100HFX, MG101FX and MG102FX is 21 amps.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates,

uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try

to correct the interference by one or more of the following measures:

* Reorient or relocate the receiving antenna.

* Increase the separation between the equipment and the receiver.

* Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

* Consult the dealer or an experienced radio/TV technician for help.

Follow all instructions and heed all warnings

KEEP THESE INSTRUCTIONS !

 

Also See for Marshall MG100FX

Related Manuals for Marshall MG100FX

0.581782s