Keurig Platinum B70 User's Manual

Keurig Coffee Makers User's Manual - Platinum B70.
Page  of 2
4.9, 1724 votes
background image

Part #:  60-200726-001
Revision B, June 2006

1. Unpacking the Platinum B70 Brewer
a. Carefully remove the Brewer by placing the box on

its side, pulling the Brewer out of the box and
removing the protective materials.

b. Place the Brewer upright on a flat surface. Remove

adhesive tape from Brewer.

c. Unwrap cord and plug Brewer into a grounded outlet.
2. Priming
a. Place a 12 oz. mug on the Drip Tray Plate.
b. Remove the Water Reservoir from the Brewer by

first removing the Lid from the Water Reservoir,
then lifting the Water Reservoir straight up and
toward the front of the Brewer. Rinse and fill with
bottled or filtered water. Replace the Water Reservoir
back on the Brewer and replace the Lid.

c. Press and release the Power switch behind the Brewer

to turn the Brewer on. Blue lights in the Water
Reservoir and LCD Control Center will become illumi-

d. The LCD Control Center will indicate ‘PRIME’ and

the Brew button will flash. Please note, a 

® portion pack should NOT be used for the

Priming Sequence.

e. Press the flashing ‘BREW’ button.

f. The Brewer will automatically fill (priming it) and then

the water will be heated. This will take about 4 minutes.
During the heating period the ‘NOT READY’ indicator
will be on. When the water is heated ‘BREW’ will be
displayed and the Brew button will flash.

g. Press the ‘BREW’ button to start a cleansing brew,

during which hot water will flow into your cup or
mug. Discard the hot water.

h. The one-time priming process is now complete and

you are ready to brew!

3. Choose
a. Place a cup or mug on the Drip Tray Plate.
b. Select a K-Cup® portion pack.

Do not remove the foil lid.

4. Brew
a. Lift the Handle, place the K-Cup in the K-Cup Holder

Assembly and then push the Handle all the way
down to puncture the K-Cup. 
Please be careful to avoid the sharp needles in the
K-Cup Assembly Housing & Lid.

b. All brew size icons are lit with the default size flash-

ing. To choose a different size, press ‘LEFT’ to go
down in size or ‘RIGHT’ to go up in size. 

c. Once size is chosen, press ‘BREW’ button. Brew but-

ton will stop flashing and icon of brew size will be lit.

Quick Start Guide

NOTE: Choosing a smaller cup size will brew
stronger tasting coffee/tea/hot cocoa.

Let the Magic Begin FAST!

Thank you for purchasing a Keurig® - Platinum B70 Gourmet Single Cup Home
Brewing System. 

IMPORTANT:  You cannot use your Keurig Brewer until it has been primed for its first use
as set forth belowPlease follow these easy steps and you will discover what Deliciously
Simple® truly means. 
Please note, if your Brewer has been exposed to temperatures below freezing, it is recommended you
allow two hours for an unpacked Brewer to warm to room temperature before priming or brew


Please consult the Use & Care Guide for additional information on your Brewer. If you
are experiencing problems, contact Customer Service at 1-866-901-BREW (2739).
© 2006 Keurig Incorporated

NOTE: The Brewer may take 15-30 seconds to reheat
between brews and the LCD Control Center will
indicate 'NOT READY'. During this time the pump
may cause a vibration noise. This is normal. The
LCD Control Center will indicate 'READY TO BREW'
once the water has heated and the Brewer is ready.

NOTE: The small mug (7.25 oz. serving) is the
factory set default brew size. To program your
favorite brew size, see page 11 in the Use & Care
Guide “Programming Your Brew Size”.