Keurig K-10 Mini Plus Brewer User Guide | Page 9

Keurig Brewers User Guide - K-10 Mini Plus Brewer.
Download
Page  of 11
4.6, 1622 votes
background image

16

17

• Brewer may be cold or frozen. Let brewer rest at room temperature for at least 2 

  hours before powering on.

• Make sure the brewer has power (see previous page). 

• Allow enough time for water in the Cold Water Reservoir to drain completely into the brewer. 

• The Exit Needle may be clogged (see page 12).

• Clean the K-Cup® Pack Assembly, if necessary (see page 12).

• De-scale the brewer (see page 14).

• If you have repeated the de-scale procedure two times and the brewer still does not 

  function properly, contact Customer Service. 

• Under normal operation, the brewer will shut off when it is idle for longer than 90 seconds. 

  Just press the Power Button to restart.

• If the brewer shuts off in the middle of a brew (not from power outage), contact Customer Service. 

• Remember that any liquid overflow (from your cup or the Cold Water Reservoir) will be 

  caught in the Drip Tray.

• When the Drip Tray is almost full, the red Drip Tray Overflow Indicator will appear. Carefully 

  remove the Drip Tray and empty its contents into the sink. 

• This means that the Drip Tray is almost full. Carefully remove the Drip Tray and empty its 

  contents into the sink.

 

SiTUATion SoLUTion

SeCtIon 6  Troubleshooting

Brewer does not have power

Brewer shuts off automatically

Brewer only brews a partial brew

Brewer will not brew when used for the first time

There is water in the Drip Tray

Red indicator appears in Drip Tray

BReW Button flashes red too long

Add Water indicator does not flash blue

Brewer will not brew

 

SiTUATion SoLUTion

• Make sure the Power Button is pressed. The Add Water Indicator should flash blue 

  after pushing the Power Button. Note that the Power Button does not illuminate. 

• During normal operation, the brewer will shut off when it is idle for longer than 90 

  seconds. Just press the Power Button to restart.

• Plug brewer into an independent outlet.

• Check to be sure that brewer is plugged in securely.

• Plug into a different outlet.

• Reset your home circuit breaker, if necessary.

• If the brewer still does not operate, contact Customer Service. 

• Under normal operation, the BREW Button will flash red when the brewer is heating and 

  will turn solid red when brewing. If the BREW Button flashes red longer than 3 minutes, 

  contact Customer Service. 

• If the Add Water Indicator does not flash blue, make sure the brewer has power (see above).

• Water may be in the Cold Water Reservoir and brewer. First, try raising the Handle to 

  drain all water from the Cold Water Reservoir into the brewer. If the light still does not flash, 

  power off and place a mug on the Drip Tray. Hold down the BREW Button and continue to 

  hold down until all the water is dispensed into the mug. 

• If the brewer still does not operate, contact Customer Service. 

• Make sure the brewer has power (see above).

• If using reverse osmosis or distilled water, the brewer may not operate correctly. See page 14 for 

  emptying the Internal Hot Water Tank and then use filtered or bottled water. 

• Press the Power Button. If the Add Water Indicator flashes blue, add water and attempt 

  to brew. If the brewer loses power during the brew process, the brewer may need to be 

  re-set when power is restored. To re-set, simply lift and lower the Handle. 

• Check that the minimum water level of 6 oz. has been poured into the Cold Water Reservoir.

Should other issues arise with your brewer, please call 
Keurig Customer Service at 1.866.901.BReW (2739).

0.574219s