Kenwood LZ-651W Owner's Manual | Page 8
Installation location and cleaning
Select for installation a location where the stand can be
placed completely horizontal or where the front edge of
the support (petal-shaped part) can be attached
horizontally as shown in Figure A.
Do not install in locations where the entire support is at a
diagonal such as in Figure B or where the monitor unit is
facing down such as in Figure C.
Thoroughly wipe away and dust or grease from the
installation location using a cloth which has been soaked
in a neutral cleaning agent and wrung out. Attach the
stand after allowing the installation location to dry.
1 Install the shoe on the rear of the TV monitor
temporarily using the supplied hexagon wrench
(Accessary C).
When adjusting the fixing screw of the shoe, use the
hexagon wrench (Accessary C) that came with the
product. Using other hexagon wrenches may damage
the screw.
2 Bend the stand support to conform to the shape of
the installation location.
3 Adjust the shape of the support so that there is no
rattling or gap when the stand is placed on the
support.
4 Peel off the protective strip from the double-sided
tape on the bottom of the stand and securely attach
the stand.
• Do not attach the double-sided tape more than once
or touch the adhesive with your fingers as this will
weaken its adhesive strength.
• If the temperature of the surface of the installation
location is low, warm it up using a heater or other
means before attaching the stand. Low temperature
may weaken the adhesive strength of the tape.
• The supplied stand is specially intended for this
product. Do not use it with another monitor.
5 Secure the stand using the supplied tapping screw
(Accessory D).
6 After attaching the stand, allow it to sit undisturbed for
24 hours. Take care not to apply any force to the stand
during this time.
7 Insert the shoe of the monitor unit into the bracket
(Accessory B).
Insert the shoe into the
bracket (Accessory B) as far
as it goes.
8 Adjust the height, horizontal and vertical angle of the
monitor unit, and securely tighten the installation
screws using the supplied hexagon wrench (Accessary
C).
You can also adjust the monitor unit's forward position
by loosening the angle adjustment knobs and
adjusting the angle of the monitor unit's installation
stand.
2CAUTION
2CAUTION
NOTE
2CAUTION
Installation for Monitor Unit
Installation
8 English
English
A
B
C
Accessory B
Accessory C
Shoe
Accessory D
Installation surface
Protective
strip
Tighten
Loosen
Accessory C
LZ-651W_ENG r2 03.7.25 9:50 AM Page 8
Related Manuals for Kenwood LZ-651W
-
Bose Audio SoundDock Series II system Owner's Manual
12 pages
-
Bose Audio SoundLink Mini Bluetooth speaker Owner's Manual
33 pages
-
Bose Audio SoundLink Bluetooth Mobile speaker II Owner's Manual
24 pages
-
Bose Audio Bose Solo TV Sound System Owner's Manual
23 pages
-
Bose Audio 301 Series V speakers Owner's Manual
10 pages
-
Bose Audio Wave music system III Owner's Manual
28 pages
-
Logitech Audio S-00078 Quick Start Manual
86 pages
-
Onkyo Audio HT-R530 Owner's Manual
71 pages
-
Pioneer Audio AVH-X2500BT Owner's Manual
212 pages
-
Technics Audio SL-1200MK2 Owner's Manual
12 pages
-
RCA Audio RT2770 Owner's Manual
2 pages
-
Alpine Audio CDE-143BT Owner's Manual
47 pages
-
Line 6 Audio Spider IV 75 Owner's Manual
33 pages
-
Behringer Audio Xenyx 802 Owner's Manual
12 pages
-
Behringer Audio Xenyx Q802USB Owner's Manual
12 pages
-
Behringer Audio Xenyx QX2442USB Owner's Manual
26 pages
-
Markbass Audio CMD 102P Owner's Manual
8 pages
-
Apple Audio iPod nano (7th generation) Owner's Manual
68 pages
-
Apple Audio iPod nano (5th generation) Owner's Manual
104 pages
-
Apple Audio iPod nano (4th generation) Owner's Manual
80 pages
-
Apple Audio iPod nano (3rd generation) Owner's Manual
72 pages
-
Apple Audio iPod nano (2nd generation) Owner's Manual
60 pages
-
Ford Audio 6000cd User's Manual
60 pages
-
QSC Audio USA 850 Owner's Manual
8 pages