Kenwood KDC-122S Owner's Manual | Page 20
English
— 20 —
Troubleshooting Guide
What might seem to be a malfunction in your unit may
just be the result of slight misoperation or miswiring.
Before calling service, first check the following table
for possible problems.
General
? The power does not turn ON.01
✔ The fuse has blown.
☞ After checking for short circuits in the wires, replace the fuse with
one with the same rating.
✔ No ACC position on vehicle ignition.02
☞ Connect the same wire to the ignition as the battery wire.
? Nothing happens when the buttons are pressed.04
✔ The computer chip in the unit is not functioning normally.
☞ Press the reset button on the unit (page 4).
? There’s a source you can’t switch.06
✔ There’s no CD inserted.
☞ Set the media you want to listen to. If there’s no media in this
unit, you can't swhich to each source.
? The memory is erased when the ignition is turned OFF.10
✔ The battery wire has not been connected to the proper terminal.
☞ Connect the wire correctly, referring to the section on
<Connecting Wires to Terminals>.
✔ The ignition and battery wire are incorrectly connected.11
☞ Connect the wire correctly, referring to the section on
<Connecting Wires to Terminals>.
? Even if Loudness is turned ON, high-pitched tone isn't compensated
for. 17
✔ Tuner source is selected.
☞ High-pitched tone isn't compensated for when in Tuner source.
? No sound can be heard, or the volume is low.
✔ The fader or balance settings are set all the way to one side.21
☞ Center the fader and balance settings.
✔ The input/output wires or wiring harness are connected incorrectly.22
☞ Reconnect the input/output wires or the wiring harness correctly.
See the section on <Connecting Wires to Terminals>.
? The sound quality is poor or distorted.25
✔ One of the speaker wires is being pinched by a screw in the car.
☞ Check the speaker wiring.
✔ The speakers are not wired correctly.27
☞ Reconnect the speaker wires so that each output terminal is
connected to a different speaker.
? The Touch Sensor Tone doesn’t sound.34
✔ The preout jack is being used.
☞ The Touch Sensor Tone can’t be output from the preout jack.
Tuner source
? Radio reception is poor.39
✔ The car antenna is not extended.
☞ Pull the antenna out all the way.
✔ The antenna control wire is not connected.40
☞ Connect the wire correctly, referring to the section on
<Connecting Wires to Terminals>.
KDC-2022/122_U.S 02.9.26 3:20 PM Page 20
Related Manuals for Kenwood KDC-122S
-
Bose Audio SoundDock Series II system Owner's Manual
12 pages
-
Bose Audio SoundLink Mini Bluetooth speaker Owner's Manual
33 pages
-
Bose Audio SoundLink Bluetooth Mobile speaker II Owner's Manual
24 pages
-
Bose Audio Bose Solo TV Sound System Owner's Manual
23 pages
-
Bose Audio 301 Series V speakers Owner's Manual
10 pages
-
Bose Audio Wave music system III Owner's Manual
28 pages
-
Logitech Audio S-00078 Quick Start Manual
86 pages
-
Onkyo Audio HT-R530 Owner's Manual
71 pages
-
Pioneer Audio AVH-X2500BT Owner's Manual
212 pages
-
Technics Audio SL-1200MK2 Owner's Manual
12 pages
-
RCA Audio RT2770 Owner's Manual
2 pages
-
Alpine Audio CDE-143BT Owner's Manual
47 pages
-
Line 6 Audio Spider IV 75 Owner's Manual
33 pages
-
Behringer Audio Xenyx 802 Owner's Manual
12 pages
-
Behringer Audio Xenyx Q802USB Owner's Manual
12 pages
-
Behringer Audio Xenyx QX2442USB Owner's Manual
26 pages
-
Markbass Audio CMD 102P Owner's Manual
8 pages
-
Apple Audio iPod nano (7th generation) Owner's Manual
68 pages
-
Apple Audio iPod nano (5th generation) Owner's Manual
104 pages
-
Apple Audio iPod nano (4th generation) Owner's Manual
80 pages
-
Apple Audio iPod nano (3rd generation) Owner's Manual
72 pages
-
Apple Audio iPod nano (2nd generation) Owner's Manual
60 pages
-
Ford Audio 6000cd User's Manual
60 pages
-
QSC Audio USA 850 Owner's Manual
8 pages