Kenwood KDC-122S Owner's Manual | Page 16
English
— 16 —
The use of any accessories except for those provided might result in
damage to the unit. Make sure only to use the accessories shipped with
the unit, as shown above.
1. To prevent a short circuit, remove the key from the ignition and
disconnect the - battery.
2. Make the proper input and output wire connections for each unit.
3. Connect the speaker wires of the wiring harness.
4. Connect the wiring harness wires in the following order: ground,
battery, ignition.
5. Connect the wiring harness connector to the unit.
6. Install the unit in your car.
7. Reconnect the - battery.
8. Press the reset button.
If you connect the ignition wire (red) and the battery wire (yellow)
to the car chassis (ground), you may cause a short circuit, that in
turn may start a fire. Always connect those wires to the power
source running through the fuse box.
• If your car's ignition does not have an ACC position, connect the
ignition wires to a power source that can be turned on and off
with the ignition key. If you connect the ignition wire to a power
source with a constant voltage supply, as with battery wires, the
battery may die.
• If the console has a lid, make sure to install the unit so that the
faceplate will not hit the lid when closing and opening.
• If the fuse blows, first make sure the wires aren’t touching to
cause a short circuit, then replace the old fuse with one with the
same rating.
• Insulate unconnected wires with vinyl tape or other similar
material. To prevent a short circuit, do not remove the caps on
the ends of the unconnected wires or the terminals.
• Connect the speaker wires correctly to the terminals to which
they correspond. The unit may be damaged or fail to work if you
share the - wires or ground them to any metal part in the car.
• When only two speakers are being connected to the system,
connect the connectors either to both the front output terminals
or to both the rear output terminals (do not mix front and rear).
For example, if you connect the + connector of the left speaker
to a front output terminal, do not connect the - connector to a
rear output terminal
• After the unit is installed, check whether the brake lamps,
blinkers, wipers, etc. on the car are working properly.
• Mount the unit so that the mounting angle is 30° or less.
2CAUTION
2WARNING
Accessories
Installation Procedure
.........1
1
3
5
External view
......... Number of items
External view
......... Number of items
.........4
4
.........2
2
.........4
.........1
(KDC-2022/KDC-2022V/
KDC-222/KDC-222S only)
KDC-2022/122_U.S 02.9.26 3:20 PM Page 16
Related Manuals for Kenwood KDC-122S
-
Bose Audio SoundDock Series II system Owner's Manual
12 pages
-
Bose Audio SoundLink Mini Bluetooth speaker Owner's Manual
33 pages
-
Bose Audio SoundLink Bluetooth Mobile speaker II Owner's Manual
24 pages
-
Bose Audio Bose Solo TV Sound System Owner's Manual
23 pages
-
Bose Audio 301 Series V speakers Owner's Manual
10 pages
-
Bose Audio Wave music system III Owner's Manual
28 pages
-
Logitech Audio S-00078 Quick Start Manual
86 pages
-
Onkyo Audio HT-R530 Owner's Manual
71 pages
-
Pioneer Audio AVH-X2500BT Owner's Manual
212 pages
-
Technics Audio SL-1200MK2 Owner's Manual
12 pages
-
RCA Audio RT2770 Owner's Manual
2 pages
-
Alpine Audio CDE-143BT Owner's Manual
47 pages
-
Line 6 Audio Spider IV 75 Owner's Manual
33 pages
-
Behringer Audio Xenyx 802 Owner's Manual
12 pages
-
Behringer Audio Xenyx Q802USB Owner's Manual
12 pages
-
Behringer Audio Xenyx QX2442USB Owner's Manual
26 pages
-
Markbass Audio CMD 102P Owner's Manual
8 pages
-
Apple Audio iPod nano (7th generation) Owner's Manual
68 pages
-
Apple Audio iPod nano (5th generation) Owner's Manual
104 pages
-
Apple Audio iPod nano (4th generation) Owner's Manual
80 pages
-
Apple Audio iPod nano (3rd generation) Owner's Manual
72 pages
-
Apple Audio iPod nano (2nd generation) Owner's Manual
60 pages
-
Ford Audio 6000cd User's Manual
60 pages
-
QSC Audio USA 850 Owner's Manual
8 pages