Intermatic ET70115 and ET70215 Owner's Manual | Page 4
duration, then press OK. Remember INTVL or PULSE override
is initiated on demand via the keypad and is not based on a day
and time, as is normal INTVL or PULSE. To initiate an override
interval or pulse first set the RUN/SET switch to RUN and set the
switch for the desired load to Enable, then press the ON/OFF key
for the load you wish to override. The green load indicator flashes
during the interval or pulse to show override selection. At the end
of an override interval or override pulse, the load and green LED
will turn off, unless a programmed ON event has occurred during
the override time period. This allows the override interval to be
used as an “early ON” as well as a “late OFF” override after
normal hours of operation without interfering with normal
scheduled ON/OFF times.
The load will respond to any subsequent program schedules. You
may also initiate an override interval or pulse by pressing and
holding the INTVL key, then pressing the ON/OFF key for the
Enabled
circuit you wish to override. This allows an override to be
started without turning off a load that is already on. This is useful
for HID lighting applications where even a brief turn off will
cause loss of lighting for several minutes. Note that override can
only be set for an interval or pulse, not both.
An override interval or pulse may be ended early only by pushing
the ON/OFF key or by a power interruption. Thus, a
programmed OFF event will not end an override interval or pulse.
At the same time, any ON or OFF events which occurred during
the override period will be in effect at the completion of the
override time period. This allows applications such as a
programmed ON time of 8:00 A.M. with a 2 hour interval
override initiation at 7:30 A.M. At 9:30 A.M., after the two hour
override, the lights will remain ON since during the override
period they were programmed to switch ON (at 8:00 A.M.).
The override pulses are precise to-the-second whereas override
interval duration is the program duration ± 30 seconds, dependent
on the instant in time when the override was initiated.
ASTRO
is pressed (instead of a time entry) after selecting a day
or day group if you want switching to occur at Sunrise and/or
Sunset. If ASTRO is pressed during the “Switch On” prompt, the
timer prompts for sunset. If ASTRO is pressed during the “Switch
Off
” prompt, the timer prompts for sunrise. For applications
requiring an ON event at sunrise and/or an OFF event at sunset,
press AM or PM respectively to toggle the sunrise/sunset prompts.
Interval programming may be used to extend the “Switch On”
and “Switch Off” times of ASTRO schedules. This is useful when
some circuits require differing offsets from the ASTRO ON/OFF
times that were entered during SET UP. To use this feature, enter
the earliest required ASTRO ON/OFF times during SET UP,
then use intervals of various durations to delay the ON/OFF times
as required. Specifically, use an ON interval to delay an ASTRO
turn OFF time and use an OFF interval to delay an ASTRO turn
ON time. Refer to the “Programming Examples” booklet for
detailed instructions. To program ASTRO switching with a Pulse or
Interval, press ASTRO, then PULSE or INTVL, followed by entering
a pulse or interval duration. . .all before OK is pressed.
(Clock adjustment for Daylight Savings Time (DST) is automatic;
see Special Instructions for override if DST adjustment is not
required, such as in Arizona, Hawaii and parts of Indiana. The
clock time will be adjusted by 1 hour on the first Sunday of April
and the last Sunday of October at 2:00 A.M. Due to unexpected
results, it is recommended you do not attempt programming from
12:00 midnight to 2:00 A.M. on these two days.)
6
Next Generation
7
Related Manuals for Intermatic ET70115 and ET70215
-
Logitech Misc Electronics O-R0004 Quick Start Manual
2 pages
-
Brother Misc Electronics DB2-B755 MKIII Owner's Manual
4 pages
-
Panasonic Misc Electronics KX-TG6572R Owner's Manual
64 pages
-
Technics Misc Electronics SA-AX720 Owner's Manual
36 pages
-
RCA Misc Electronics RCR504BR Owner's Manual
2 pages
-
RCA Misc Electronics RCRN04GR Owner's Manual
2 pages
-
RCA Misc Electronics RCRBB04GR Owner's Manual
6 pages
-
Intermatic Misc Electronics GM40AVE Owner's Manual
12 pages
-
Intermatic Misc Electronics ET1705C Owner's Manual
4 pages
-
Kidde Misc Electronics Firex 2650-560,2650-561 English MA2650 Owner's Manual
6 pages
-
Trane Misc Electronics XL800 Owner's Manual
8 pages
-
Trane Misc Electronics XL803 Owner's Manual
8 pages
-
Trane Misc Electronics XL624 Owner's Manual
8 pages
-
Trane Misc Electronics XL600 Owner's Manual
8 pages
-
Trane Misc Electronics XL80 Owner's Manual
12 pages
-
Trane Misc Electronics XR80 Owner's Manual
12 pages
-
Trane Misc Electronics XB80 Owner's Manual
12 pages
-
Troy-Bilt Misc Electronics CS 4325 Chipper Shredder Owner's Manual
36 pages
-
Troy-Bilt Misc Electronics TB146 EC 4-Cycle Garden Cultivator Owner's Manual
16 pages
-
Troy-Bilt Misc Electronics TB516 EC Lawn Edger Owner's Manual
12 pages
-
Troy-Bilt Misc Electronics Colt FT Garden Tiller Owner's Manual
36 pages
-
Linear Misc Electronics AP-4 Owner's Manual
2 pages
-
Brother Misc Electronics KE-430F Parts Manual
68 pages
-
Hunter Misc Electronics XC Programming Instructions Manual
18 pages