Intermatic ET70115 and ET70215 Owner's Manual | Page 3
These keys are used for most data entry. Note dual functions,
numeric or day specific. Using the day group keys WKDY,
and ALL (for all 7 days) greatly speeds the process.
The keypad keys are only functional when the RUN/SET switch is
in the SET position. Pressing keys when in the RUN position will
cause a message to scroll, explaining the function of that key. Press
any key once to stop any of the scrolling error or help messages.
You must press AM or PM after entering time data (except Sunrise
or Sunset) unless in 24-hr. mode. Programming fixed times for
ON and OFF events does not require PULSE, INTVL or ASTRO
keys. Multiple ONs or OFFs can be entered by pressing OK
without programming the alternate OFF or ON. Multiple OFF
times are frequently used to “sweep” off loads which have been
manually switched on after normal occupancy hours.
PULSE and INTVL (Interval) are length-of-time based options.
Maximum Pulse is 127 sec.; minimum is 1 sec. Maximum Interval
is 6 days, 23 hrs., 59 min.; minimum is 1 min. To program Pulses
or Intervals, press the PULSE or INTVL key after entering a Switch
or Switch Off time; then enter the required duration and press
. Note after ON Pulses or Intervals have timed out the load
will be OFF, and after OFF Pulses or Intervals have timed out the
load will be ON, regardless of the load state prior to the start of
the Pulse or Interval. The INTVL and PULSE keys include a
temporary override function with a maximum length of 6 days, 23
hrs. and 59 min. for the interval or 127 seconds for the pulse. To
program an interval or pulse for override, select SET, enable the
circuit, press PROG, press INTVL
or PULSE (without selecting a
day), key in the interval or pulse
SET UP is performed once during
installation to set the internal CLOCK, ASTRO (sunrise/sunset)
times and HOLIDAY references. After entering and okaying the
ASTRO Zone, the timer will display calculated “center of time
zone” times when prompting for sunrise and sunset entries. You
may OK these, enter actual sunrise/sunset times or enter offset
times for early or late ASTRO operation. Sunrise time must be
before noon; sunset time must be after noon. Sunset must not be
within 5 hours of sunrise. Both sunrise and sunset must be
entered, even if only one is used for switching. If neither is
required, you may skip ahead by pressing HLDY or PROG keys.
(See map pp. 24–25 for details.) Holidays are entered with 2-digit
reference numbers; a chart for recording the date(s) is located on
page 22. Leap years are preset through the year 2094.
PROGRAM is used for entering or
changing the switching schedule for loads wired into the time
switch. You can program circuits separately or concurrently. Each
entry affects loads whose Enable switches are in the enable
position at the time of data entry (2 circuit models only). The
time switch is shipped in a 12-hr. AM/PM mode; you can change
to 24-hr. by removing a jumper on the circuit board (see Special
Instructions). It can store a minimum of 400 events, depending
on the data type entered.
The time switch prompts you through SET UP and PROGRAM
with LEDs that advance after each entry. There are five important
points to remember:
1) The RUN/SET switch must be in the SET position to enter,
review or change data.
2) You must press “OK” after each entry, before starting the next.
3) You must press AM or PM after entering time (unless
programming Sunrise and Sunset or in 24-hour mode).
4) When in PROGRAM you must select the loads you want to
control with the Enable switches (2 circuit models only).
5) RUN/SET switch must be returned to RUN position to enable
automatic control and to save changes to data.
P R O G R A M
S E T U P
Related Manuals for Intermatic ET70115 and ET70215
Logitech Misc Electronics O-R0004 Quick Start Manual
Brother Misc Electronics DB2-B755 MKIII Owner's Manual
Panasonic Misc Electronics KX-TG6572R Owner's Manual
Technics Misc Electronics SA-AX720 Owner's Manual
RCA Misc Electronics RCR504BR Owner's Manual
RCA Misc Electronics RCRN04GR Owner's Manual
RCA Misc Electronics RCRBB04GR Owner's Manual
Intermatic Misc Electronics GM40AVE Owner's Manual
Intermatic Misc Electronics ET1705C Owner's Manual
Kidde Misc Electronics Firex 2650-560,2650-561 English MA2650 Owner's Manual
Trane Misc Electronics XL800 Owner's Manual
Trane Misc Electronics XL803 Owner's Manual
Trane Misc Electronics XL624 Owner's Manual
Trane Misc Electronics XL600 Owner's Manual
Trane Misc Electronics XL80 Owner's Manual
Trane Misc Electronics XR80 Owner's Manual
Trane Misc Electronics XB80 Owner's Manual
Troy-Bilt Misc Electronics CS 4325 Chipper Shredder Owner's Manual
Troy-Bilt Misc Electronics TB146 EC 4-Cycle Garden Cultivator Owner's Manual
Troy-Bilt Misc Electronics TB516 EC Lawn Edger Owner's Manual
Troy-Bilt Misc Electronics Colt FT Garden Tiller Owner's Manual
Linear Misc Electronics AP-4 Owner's Manual
Brother Misc Electronics KE-430F Parts Manual
Hunter Misc Electronics XC Programming Instructions Manual