Ingersoll-Rand X41 User's Manual | Page 26

Ingersoll-Rand Air Compressor User's Manual - X41.
Download
Page  of 85
4.5, 2418 votes
background image

X4I Interconnect To Ingersoll Rand Intellisys SE Controlled Compressors

Refer to the X4I Overview Drawing for the X4I Compressor 2 through 4 X01 to IR-PCB terminal connections

For All SE Intellisys Controlled Machines:

The 'SEQUENCER' setting of the Intellisys controller must be set to 'ON'. 

Auto Restart must be turned 'ON’ to allow the machines to stop in Auto restart when unloaded by the X4I.

The Intellisys must be run in the Online/Offline regulation mode. Do not use Modulation or ACS. 

Check the Intellisys software revision level.  Always update to the latest revision prior to operation.  

For UP SE Intellisys Controllers,  

Minimum Software Version 1.11
CCN: 39217047 (w/o PORO)  
CCN: 39217039 (w PORO)

When installing the Sequence Option to enable Remote Load/Unload, the Remote Start Stop input terminals are now used for the Remote Load 

I

nputs.  Remote Start Stop will no longer be functional. The SI1 interface (CCN: 42425710) can be used in place of the Sequence Option to allow 
the SE controlled machines to function with both Remote Load Unload and Remote Start Stop.

Software Version 1.20 and Greater

The 'CONTACT SEQUENCE' setting of the Intellisys controller must be set to 'ON'.

Drawing Notes For UP SE Intellisys Controlled Machines:

Note:  For Star Delta starter wiring the X4I Run signal should be connected directly to the 1M coil.

Note:  For Full voltage wiring the 1S (1Sb) interlock will not be used. The X4I Run signal can be connected directly to the Intellisys J5-1 terminal.

Note:  For Pegasus machines wiring may be factory installed connecting the Intellisys Alarm Relay J5-9, J5-10 and J5-11 to a terminal strip but unused. Remove any factory installed 
wiring from the Intellisys Alarm Relay contacts and connect the X4I Interface board wiring directly to the Intellisys Alarm Relay terminals J5-9 and J5-10.

For ESA SE Intellisys Controllers, the 'SEQUENCER Option’ must be purchased. installed and then turned on.   

Minimum Software Version 1.40
CCN: 39217047 (w/o PORO)  
CCN: 39217039 (w PORO)

When installing the Sequence Option to enable Remote Load/Unload, the Remote Start Stop input terminals are now used for the Remote Load 

I

nputs.  Remote Start Stop will no longer be functional. The SI1 interface (CCN: 42425710) can be used in place of the Sequence Option to allow 
the SE controlled machines to function with both Remote Load Unload and Remote Start Stop.

Drawing Notes For ESA SE Intellisys Controlled Machines:

Note:  For Star Delta starter wiring the X4I Run signal should be connected directly to the 1M coil.

Note:  For Full voltage wiring the 1S (1Sb) interlock will not be used. The X4I Run signal can be connected directly to the Intellisys J5-1 terminal.

For DSA SE Intellisys Controllers, the 'SEQUENCER Option’ must be purchased. installed and then turned on.   

CCN: 22179238

When installing the Sequence Option to enable Remote Load/Unload, the Remote Start Stop input terminals are now used for the Remote Load 
inputs.  Remote Start Stop will no longer be functional. The SI1 interface (CCN: 42425710) can be used in place of the Sequence Option to allow 
the SE controlled machines to function with both Remote Load Unload and Remote Start Stop.

Drawing Notes For DSA SE Intellisys Controlled Machines:

Note:  For Star Delta starter wiring the X4I Run signal should be connected directly to the 1M coil.

Note:  For Full Voltage wiring, the 1S (1Sb) interlock will not be used. The X4I Run signal can be connected directly to the Intellisys terminal 42.

For Sierra SE Intellisys Controllers, the SI1 interface (CCN: 42425710) must be used to allow the SE Controller to be sequenced/controlled by the X4I 

Guidance only; connections may differ with date, model, type, variant, special, custom or concession builds. This information is intended to be 
used in conjunction with the compressor’s original control circuit diagram.

 

X4I Interconnect To Ingersoll Rand Intellisys SE Controlled Compressors  Page 26

Related Manuals for Ingersoll-Rand X41

0.543141s