Ingersoll-Rand FE074B( )A( ) User's Manual
E1999 INGERSOLL–RAND COMPANY D PRINTED IN U.S.A.
Ingersoll–Rand Company
1725 U.S. No. 1 North
D P.O. Box 8000 D Southern Pines, NC 28388–8000
ARO Tool Products
For parts and service information, contact your local ARO distributor, or the Customer Service Dept. of the Ingersoll–Rand Distribution
Center, White House, TN at PH: (615) 672–0321, FAX: (615) 672–0801.
OPERATOR’S MANUAL
SECTION
M107
MANUAL
26
Released: 5-15-98
Revised: 11-20-99
49999-543
INCLUDING:ĂOPERATION,ĂINSTALLATIONĂ&ĂMAINTENANCE
Models FE074B–( )–A( )
SERIES 7 ELECTRA–FEED DRILL
READ THIS MANUAL CAREFULLY BEFORE INSTALLING,
OPERATING OR SERVICING THIS EQUIPMENT.
It is the responsibility of the employer to place this information in the hands of the operator. Keep for future reference.
R
OPERATING AND SAFETY PRECAUTIONS
• Keep hands and clothing away from rotating end of tool and all
moving parts of the tool.
• Wear suitable eye protection while operating tool or when
near tool when it is being operated.
• Disconnect air and electrical supply from tool before remov-
ing/installing bits or performing other maintenance or service
procedures.
ROUTINE LUBRICATION REQUIREMENTS
When this tool was built, an “O” ring lubricant was applied to all ap-
propriate dynamic seals to insure continued operation. Drive train
components and bearings were also supplied / filled with grease
to insure appropriate life of components. As long as all exterior
seals and wipers are maintained in good working order and all
covers and breather vents are kept in place, it is reasonable to ex-
pect that external debris will not enter the tool. It is also reason-
able to expect that lubricants applied to the tool interior will require
replenishment for at least 5000 hours of normal operation.
Adding spindle oil to the power air inlet of this tool is not
necessary.
MOUNTING
Mounting clamps 49690 and 46982–1 are available for mounting
of this tool. These items are shown on page 11. Both mounts allow
the clamp to grip the outer sleeve of the tool and feature keyways
for alignment.
AIR SUPPLY REQUIREMENTS
For maximum operating efficiency, the following air supply specifi-
cations should be maintained to this air tool:
• AIR PRESSURE – 90 PSIG (6 bar)
• AIR FILTRATION – 50 micron
• HOSE SIZE – 5/16” (8 mm) I.D.
An ARO
R model P29231–110 air line FILTER/REGULATOR plus
100067 gauge is recommended to maintain the above air supply
specifications.
RECOMMENDED LUBRICANTS
After disassembly is complete, all parts, except sealed or shielded
bearings, should be washed with solvent. To relubricate parts, or
for routine lubrication, use the following recommended lubricants:
Where Used
ARO Part #
Description
‘‘O” Rings, Lip Seals
and Air Cylinder
36460
4 oz. Stringy Lubricant
Sliding Splines and
Bearings
33153
5 lb. ‘‘EP” – NLGI #1
Grease
Related Manuals for Ingersoll-Rand FE074B( )A( )
-
GE Drill GXWH40L Installation Manual
12 pages
-
Parkside Drill PABS 14.4 A1 Operation Manual
35 pages
-
Sears Drill 113.21371 Instruction Manual
24 pages
-
Indesit Drill IWB 5113 User's Manual
16 pages
-
Indesit Drill IWB 5113 User's Manual
16 pages
-
Black & Decker Drill Fire Storm FS1802 Instruction Manual
5 pages
-
Black & Decker Drill 7190-04 Owner's Manual
16 pages
-
Craftsman Drill 137.219 User's Manual
24 pages
-
DeWalt Drill D21570 Instruction Manual
12 pages
-
DeWalt Drill DW235G Instruction Manual
6 pages
-
DeWalt Drill DWD024 Instruction Manual
32 pages
-
GE Drill GE752 User's Manual
82 pages
-
Husqvarna Drill DM 340 User's Manual
16 pages
-
Dremel Drill MOTO-TOOL 285 User's Manual
8 pages
-
Sears Drill 113.24611 User's Manual
24 pages
-
Sears Drill 149.21334 User's Manual
16 pages
-
Sears Drill KENMORE LAUNDRY CENTER 95761 User's Manual
16 pages
-
Milwaukee Drill 4208-1 User's Manual
25 pages
-
Milwaukee Drill 4297-1 User's Manual
25 pages
-
Milwaukee Drill Heavy-Duty 3/8 Hammer-Drills User's Manual
20 pages
-
Digitrex Drill Mark III Directional Drilling Locating System 3-3000-00a-F User's Manual
92 pages
-
Craftsman Drill C3 19.2-Volt 1/2 Impact Wrench Owner's Manual
20 pages
-
STIHL Drill BT 121 Earth Auger Instruction Manual
66 pages
-
STIHL Drill BT 130 Earth Auger Instruction Manual
68 pages