Humminbird Kayak-Transducer Owner's Manual
1b. If the cables cannot be routed directly
beneath the mounting bracket, mark and
drill a 1" hole that will allow you to run the
cables close to the bracket. Pass the cables
through the 1" hole, through the mounting
base, and out of the top of the mounting
bracket (Figure 5). Using needle-nose pliers,
break out the tabs on the rear of the
mounting base (Figure 6). Place the hole
cover over the mounting surface hole, then
use it to mark the position of the two
mounting screws. Remove the Hole Cover,
drill the two mounting holes using a 9/64"
(3.5 mm) bit, fill them with marine-grade
silicone, then replace the Hole Cover and
insert the #8 Phillips countersink wood
screws. Hand-tighten only!
2. Place the mounting bracket on the
mounting surface aligned with the drilled
holes and fill the mounting holes with
marine grade silicone. Insert the four #8
Phillips countersink wood screws into the
mounting holes. Hand-tighten only!
TRANSDUCER INSTALLATION
1. Testing the Transducer
Prior to installation, test the transducer to make sure that no damage occurred
during shipping.
1. Connect the transducer to the control head and remove any film from the
transducer.
2. Hold the transducer in the water over the side of the boat to confirm
proper operation. If the transducer is working properly, the control head
will begin displaying data immediately.
2. Locating the Transducer Mounting Position
You must first determine the best location
to mount the kayak transducer (Figure 7).
• Select a location inside the hull, in
the center, lower part of the kayak, in
which the area forward of this
location is smooth, flat, and free of
protrusions or ribs.
• The transducer should be mounted
parallel to the water line so that it
points straight down.
• Select a location that will allow the
transducer cable to easily connect to
the control head.
3. Mounting the Transducer
Prepare the mounting area and secure the transducer using the following
procedures.
1. Scuff the mounting area with the scrub pad (included) so that it covers a
diameter of 6”. The scuffed area should extend beyond the edges of the
transducer bracket (included) when it is applied in the following steps.
2. Clean the scuffed area and the transducer bracket (included) with the
alcohol wipe (included). Allow the cleaned areas to dry completely.
3. Wipe the cleaned, scuffed area with the cotton-end of the primer tube
(included). Then, activate the primer by squeezing the middle of the tube
until the internal bubble cracks, and apply the primer to the scuffed area.
Allow the primer to dry completely.
4. Peel the tan liner from the ad-
hesive backing (included), and
place the adhesive side of the
backing onto the flat rim of the
bracket. The red liner will be face-
up. Press firmly around all surfaces
of the adhesive backing so that it
is sealed evenly to the bracket rim
(Figure 8).
5. Peel the red liner from the
adhesive backing. Orient the
pointed end of the bracket toward
the front of the boat, and attach
the bracket onto the prepared
mounting area of your kayak. Press
and hold the bracket firmly to the
kayak so that it bonds evenly to the
surface (Figure 9).
Bracket
(rim side down)
Figure 9
Inside Hull
(cut-away view)
Scuffed Mounting area
Adhesive Backing
(red side up)
Figure 8
Bracket
Bracket Rim
Figure 7
Side View
(parallel with water line)
Bottom View
(flat part of boat)
Kayak Type I
Side View
(parallel with water line)
Bottom View
(flat part of boat)
Kayak Type II
Break-out
tabs
Figure 6
Hole Cover
Figure 5
There are five basic installation tasks that you must perform for the
Humminbird® Fishing System:
• Installing the Humminbird® control head
• Installing the transducer
• Installing the battery
• Routing the cables and attaching the cable connector
• Testing the complete installation
NOTE: The transducer will be installed inside the hull. In-hull mounting generally produces
good results in single thickness fiberglass-hul ed boats. The integral temperature probe
will not work with in-hul mounting, so you may want to consider purchasing a
Temperature/Speed accessory or a Temp Sensor.
NOTE: If the included transducer will not work for your application, you may exchange it,
NEW and UNASSEMBLED, with mounting hardware included, for a transducer
appropriate for your application - often at very little or no charge depending on the
transducer. Call the Humminbird® Customer Resource Center at 1-800-633-1468 for
details and pricing, or visit www.humminbird.com.
CONTROL HEAD INSTALLATION
1. Determine Where to Mount
Begin the installation by determining where to mount the control head.
Consider the following to determine the best location:
• To check the location planned for the control head, test run the cables for
the transducer, power, and optional-purchase Temp/Speed accessory (if
applicable). See the transducer and battery installation sections to plan
the mounting locations.
• There are two ways to route the cables to the unit: through a hole in the
mounting surface underneath the mounting bracket, or from a hole
outside the mounting bracket. Routing the cables under the mounting
bracket provides maximum weather protection; this may not be feasible,
however, if the area under the control head is inaccessible. In this case,
route the cables through a hole at another location and cover with the
supplied hole cover.
• The mounting surface should be stable enough
to protect the control head from excessive
wave shock and vibration, and should provide
visibility while in operation.
• The mounting area should allow sufficient
room for the unit to pivot and swivel freely,
and for easy removal and installation (Figures
1 and 2).
2. Drill the Mounting Bracket Mounting Holes
1. Set the control head mounting bracket in place
on the mounting surface. Mark the four
mounting screw locations with a pencil or
punch.
2. Set the mounting bracket aside, and drill the
four mounting screw holes using a 9/64" bit.
3. Route the Cables Through the Mounting Bracket
1a. If the cables must pass through a hole directly
beneath the mounting bracket, mark and drill
an additional 1" hole centered between the
four mounting holes (Figure 3). Route the
cables through the grommet, then press the
grommet in place around the cables and into
the 1" hole. Pass the cables out of the top of
the mounting bracket (Figure 4).
or...
1" Hole Location
Mounting Hole Locations
Figure 3
Cables
Mounting
Bracket
Grommet
Figure 4
NOTE: When drilling holes in fiberglass hulls, it is
best to start with a smaller bit and use progressively
larger drill bits to reduce the chance of chipping or
flaking the outer coating.
Figure 2
Figure 1
NOTE: In addition to the hardware supplied with your transducer, you will need a
powered hand drill and various drill bits, marine-grade silicone sealant, and various
hand tools, including a crimp tool, a ruler or straightedge, a level, marker or pencil,
safety glasses, and dust mask.
NOTE: Due to the wide variety of hul s, only general instructions are presented in this
instal ation guide. Each boat hul represents a unique set of requirements that should
be evaluated prior to instal ation. It is important to read the instructions completely and
understand the mounting guidelines before beginning instal ation.
6. After the bracket and adhesive have cured for 24 hours, empty the whole
packet of marine-grease (included) into the bracket center. Make sure it
covers the bottom and inner-sides of the bracket.
NOTE: The marine-grease is environmentally-friendly material.
7. Place the transducer into the center
of the bracket. Push down on the
transducer until you feel it contact
with the bottom of your kayak.
Wiggle the transducer slightly from
side to side to reduce air bubbles
(Figure 10).
8. Thread
the
tie-down
strap
(included) through the bracket
holes, and connect both ends of the
strap over the top by looping the
small end through the tie-down
strap hole. Make sure that the strap
is
pulled
tight
around
the
transducer and that the transducer
is seated securely in the bracket
(Figure 11).
BATTERY INSTALLATION
1. Charging the Battery
A 6' long power cable is included to supply power to the control head.
NOTE: Humminbird® is not responsible for over-voltage or over-current failures.
1. Charge the battery, using the included battery charger, until it is fully
charged. Charging usually requires 8 continuous hours but may vary
depending on your configuration. The LED on the charger will turn green
when the battery is fully charged.
NOTE: Some international models may not include a battery or battery charger.
CAUTION! Do not pull on the battery or charger cables when you are trying to connect
them to or disconnect them from the battery terminals. Push or pull gently on the spade
terminals instead. If the connector feels tight, use a slight wiggling motion to slide the
spade connector into place on the terminal (Figure 12).
2. Installing the Battery Dry Bag
1. Slide the included spade clips over the power
cable wires and crimp the connections closed
with a crimp tool (Figures 13 and 14).
2. Slide the spade clips over the battery terminals,
connecting the red wire to the red terminal,
and the black wire to the black terminal.
CAUTION! Do not pull on the battery wires when you are
trying to connect to the battery terminals (Figure 12).
3. With the dry bag resting on a stable surface,
place the battery into the bottom of the dry bag
(Figure 15).
4. Pull the power cable out of the dry bag and set
it to one side. Seal the dry bag, roll it down, and
buckle it closed (Figure 16).
5. Place the closed dry bag inside the hull. Make
sure the dry bag is secured so it does not slide
or pull on the power cable. The dry bag should
be secured in the hull, on a flat surface, stable
enough to protect the battery from water,
movement, and vibration.
NOTE: The included dry bag is water resistant
but not waterproof. Do not submerge the dry bag
or battery in water at any time.
CAUTION! Make sure that the power cable is
NOT connected to the control head at the
beginning of this procedure.
Figure 13
Figure 14
Figure 15
Figure 16
Figure 12
NOTE: The battery charger uses a yellow LED to indicate it is charging. On some
models, this light might appear closer to orange than yellow. When this happens,
the battery is still charging properly and should be left to charge until the LED
becomes green.
CAUTION! Make sure that the power cable is NOT connected to the control head at
the beginning of this procedure.
Figure 11
Tie-Down Strap
Bracket Holes
Transducer
Figure 10
Bracket
Inside Hull (cut-away view)
NOTE: Al ow the adhesive 24 hours to dry. Proceeding before the 24 hour period
may cause the kayak transducer mount to fal off in high heat.
ROUTING THE CABLES & TESTING
1. Assembling the Connector Holder
NOTE: You must install your transducer, and route the
transducer cable and power cable as described in the
previous sections, before you can install the connector
holder in this procedure.
1. Insert both the power and the transducer
cable plugs into the connector holder.
The cable plugs are labeled, and there
are
corresponding
labels
on
the
connector holder (Figure 17). The slots for
the plugs are keyed to prevent reversed
installation, and insertion should be easy
- do not force plugs.
2. Carefully pull the excess cable from
beneath the mounting surface so that
the connector holder aligns with the
mounting holes on the front of the
mounting bracket (Figure 18).
3. Snap the support plate onto the rear of
the connector holder (Figure 19).
4. Insert the connector holder into place
and fasten it to the mounting bracket
using the two #6-19 x 3/4" screws (Figure
20). Hand-tighten only.
5. Slide the control head onto the mounting
bracket until it is fully seated. To remove
the unit, grasp the unit with both hands,
then firmly press the latch on the rear of
the unit and lift (Figure 21).
NOTE: This latch is heavy-duty to withstand marine
use, and significant force must be applied.
2. Test and Finish the Installation
Once you have installed the control head, transducer, and power, and have
routed all the cables, you should perform a final test. Testing should be
performed with the boat in the water.
1. Press POWER once to turn on the control head. If the unit does not power
up, make sure that the connector holder is fully seated in the receptacle
and that power is available.
2. If all connections are correct and power is available, the Humminbird®
control head will enter Normal operation.
3. If the bottom is visible on-screen with a digital depth readout, the unit is
working properly. Make sure that the boat is in water greater than 2' but
less than the depth capability of the unit, since the sonar signal cannot
pass through air.
STORING THE
HUMMINBIRD FISHFINDER
You should take the control head and battery with you when not in use,
during transportation, or storage.
1. Power Off the control head.
2. Unplug the power cable and transducer cable if you are not planning
continued operation.
3. Remove the control head from the quick disconnect mount, and cover
the mount with the included cover.
4. Remove the battery from the dry bag so that you can charge it for
future use.
NOTE: Recharge the battery after each use.
Never leave your Humminbird® in a closed car or trunk - the
extremely high temperatures generated in hot weather can damage
the electronics. Repairs should be performed only by authorized
Humminbird® technicians.
Transducer
Accessory
Figure 17
Communications
Power
Connector Holder
Connector
Holder
Cable
Connector
Figure 18
Support Plate
Figure 19
Figure 20
Figure 21
Firmly Press
Latch to
Remove
Unit
REMOVING THE TRANSDUCER
It is not required to uninstall your transducer from your kayak, but if you choose
to do so, follow the steps below:
1. Carefully disconnect the transducer cable from the control head.
2. Unfasten the tie-down strap from the bracket.
3. Remove the transducer from the bracket.
If you choose to remove the transducer from the bracket and reinstal at a later time,
additional marine-grease wil be needed. Contact the Customer Resource Center at
www.humminbird.com or cal 1-800-633-1468 for more information.
SPECIFICATIONS
Unit Size (Standard Mount) . . . . . . . . . . . . . . . . . . . . . . . .5.25" W x 7.4" H x 4" D
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 Volt (7 Amp Hour)
Transducer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .XNT 9 20 T
CONTACT HUMMINBIRD®
Contact the Humminbird® Customer Resource Center in any of the following
ways:
By Telephone:
(Monday - Friday 8:00 a.m. to 4:30 p.m.
Central Standard Time):
1-800-633-1468
By e-mail:
(typically we respond to your e-mail
within three business days):
cservice@johnsonoutdoors.com
For direct shipping,
our address is:
Humminbird
Service Department
678 Humminbird Lane
Eufaula, AL 36027 USA
WARNING! Disassembly and repair of this electronic unit should only be performed by
authorized service personnel. Any modification of the serial number or attempt to repair
the original equipment or accessories by unauthorized individuals will void the warranty.
WARNING! This product contains chemicals known to the State of California to cause
cancer and/or reproductive harm.
WARNING! Do not travel at high speed with the unit cover installed. Remove the unit
cover before traveling at speeds above 20 mph.
ENVIRONMENTAL COMPLIANCE STATEMENT: It is the intention of Humminbird® to
be a responsible corporate citizen, operating in compliance with known and applicable
environmental regulations, and a good neighbor in the communities where we make or
sell our products.
WEEE DIRECTIVE: EU Directive 2002/96/EC “Waste of Electrical and Electronic
Equipment Directive (WEEE)” impacts most distributors, sellers, and manufacturers of
consumer electronics in the European Union. The WEEE Directive requires the producer of
consumer electronics to take responsibility for the management of waste from their
products to achieve environmentally responsible disposal during the product life cycle.
WEEE compliance may not be required in your location for electrical & electronic
equipment (EEE), nor may it be required for EEE designed and intended as fixed or
temporary installation in transportation vehicles such as automobiles, aircraft, and boats.
In some European Union member states, these vehicles are considered outside of the
scope of the Directive, and EEE for those applications can be considered excluded from the
WEEE Directive requirement.
This symbol (WEEE wheelie bin) on product indicates the product must not be
disposed of with other household refuse. It must be disposed of and collected for
recycling and recovery of waste EEE. Humminbird® will mark all EEE products in
accordance with the WEEE Directive. It is our goal to comply in the collection,
treatment, recovery, and environmentally sound disposal of those products; however,
these requirements do vary within European Union member states. For more information
about where you should dispose of your waste equipment for recycling and recovery
and/or your European Union member state requirements, please contact your dealer or
distributor from which your product was purchased.
HUMMINBIRD®
KAYAK INSTALLATION GUIDE
531763-1_A
Related Manuals for Humminbird Kayak-Transducer
-
Logitech Misc Electronics O-R0004 Quick Start Manual
2 pages
-
Brother Misc Electronics DB2-B755 MKIII Owner's Manual
4 pages
-
Panasonic Misc Electronics KX-TG6572R Owner's Manual
64 pages
-
Technics Misc Electronics SA-AX720 Owner's Manual
36 pages
-
RCA Misc Electronics RCR504BR Owner's Manual
2 pages
-
RCA Misc Electronics RCRN04GR Owner's Manual
2 pages
-
Intermatic Misc Electronics GM40AVE Owner's Manual
12 pages
-
Intermatic Misc Electronics ET70115 and ET70215 Owner's Manual
20 pages
-
Intermatic Misc Electronics ET1705C Owner's Manual
4 pages
-
Kidde Misc Electronics Firex 2650-560,2650-561 English MA2650 Owner's Manual
6 pages
-
Trane Misc Electronics XL800 Owner's Manual
8 pages
-
Trane Misc Electronics XL803 Owner's Manual
8 pages
-
Trane Misc Electronics XL624 Owner's Manual
8 pages
-
Trane Misc Electronics XL600 Owner's Manual
8 pages
-
Trane Misc Electronics XL80 Owner's Manual
12 pages
-
Trane Misc Electronics XR80 Owner's Manual
12 pages
-
Trane Misc Electronics XB80 Owner's Manual
12 pages
-
Troy-Bilt Misc Electronics CS 4325 Chipper Shredder Owner's Manual
36 pages
-
Troy-Bilt Misc Electronics TB146 EC 4-Cycle Garden Cultivator Owner's Manual
16 pages
-
Troy-Bilt Misc Electronics TB516 EC Lawn Edger Owner's Manual
12 pages
-
Troy-Bilt Misc Electronics Colt FT Garden Tiller Owner's Manual
36 pages
-
Linear Misc Electronics AP-4 Owner's Manual
2 pages
-
Brother Misc Electronics KE-430F Parts Manual
68 pages
-
Hunter Misc Electronics XC Programming Instructions Manual
18 pages