HP Officejet g95 All-in-One Printer Quick Setup Guide

HP All in One Printer Quick Setup Guide - Officejet g95 All-in-One Printer.
Download
Page  of 2
4.7, 1144 votes
background image

Rest the box on its
side, and pull out
your HP OfficeJet.

This poster provides instructions for setting up an HP
OfficeJet on a network. If you are not setting up your HP
OfficeJet on a network, refer to

for more information.

Before you set up your HP OfficeJet, you must have the
following:

HP OfficeJet G Series:

Your Basic Guide

Network Requirements

With the box upright,
remove print cartridges,
HP two-sided printing
accessory and HP
JetDirect Print Server.

Make sure you have the
following

items:

key

a

b

c

Connect office equipment

(optional)

This diagram shows a possible configuration for
connecting additional office equipment.

For each piece of office equipment you are
connecting to the HP OfficeJet, remove a plastic
tab from the phone/fax connector.

If you connect a PC modem, turn off its fax-receive
feature. See your Onscreen Guide for information
on tone versus pulse dialing and features such as
distinctive ring or voice mail.

5

Load paper

7

c

a

b

c

Unpack your HP OfficeJet

Connect the HP JetDirect Print Server

To install the HP JetDirect Print
Server, follow these steps:
a. Connect the HP JetDirect Print

Server to the network using an
RJ-45 network cable.

b. Connect the HP OfficeJet to the

HP JetDirect Print Server using
the supplied parallel cable.

c. Plug the power supply into the

HP JetDirect Print Server, and
then into a power outlet.

2

HP
OfficeJet

HP JetDirect
Print Server

Network hub
or switch

Computer

a

c

b

1

Connect the phone/fax cord to the HP
OfficeJet and then to the wall jack.

Connect the power cord

Connect the power
supply and the
adapter.

Make sure the Automatic
Document Feeder cord is
securely connected to
the unit.

4

a

b

c

Advanced Users Only:
For advanced information,
such as setting up on a
Novell network or NT server,
see the documentation that
is packaged with your HP
JetDirect Print Server.

J3256 B

10

Test

Parallel

Parallel Cable

RJ-45 Network Cable

Power

Input

9-35 VDC

Back View of HP JetDirect

HP OfficeJet G95 Quick Setup Poster

http://www.hp.com/go/all-in-one

Turn page over for additional setup.

Open the door
and raise it up
until it clicks
into place. The
print-cartridge
carriage
moves to the
middle of the
access area.

Lower the right print-cartridge
latch down onto the top of the
cartridge, and push down until
the latch locks firmly into place.

Remove the black print cartridge (thinner one)
from its packaging and, being careful to touch
only the black plastic, gently remove both the
green pull tab and the blue tape covering the
nozzles.

Push the black print cartridge
firmly down into the slot on the
right. As you insert the cartridge,
make sure the label is facing you.

Insert black print cartridge

CAUTION:
Do not touch
or remove
the gold-
colored
contacts.

a

d

b

c

e

Raise both latches on the
print carriage.

8

Insert the HP two-sided printing
accessory into the back of the
HP OfficeJet. Make sure it
snaps in place.

Turn the knob on the unit’s
rear access door counter-
clockwise and remove the
door.

b

Attach HP two-sided printing accessory

3

Turn on your HP OfficeJet

6

HP JetDirect

print cartridges

HP JetDirect box

installation CD

HP two-sided
printing accessory

power adapter

power cord

parallel cable

1

3

2

phone cord

Check
connection
here

• A working 10Base-T Ethernet network using TCP/IP

or IPX/SPX protocols

• Network PCs that meet the system requirements for the

HP OfficeJet including supported network
operating systems

• An open port on a 10Base-T network hub or switch
• A CAT 5 network cable with RJ-45 connectors

a

Also See for HP Officejet g95 All-in-One Printer

Related Manuals for HP Officejet g95 All-in-One Printer

0.520966s