Hotpoint fdl570 User's Manual | Page 8

Hotpoint Range User's Manual - fdl570.
Download
Page  of 20
4.2, 1798 votes
background image

8

EN

Start-up and use

Measuring out the detergent

A good wash result also depends on the correct amount of

detergent being used; exceeding the stated amount does not

result in a more effective wash and increases environmental

pollution.

    Only use detergent which has been

specifically  designed  for  dishwashers.

 DO NOT USE washing up liquid.
 Using excessive detergent may result in foam

residue remaining in the machine after the cycle

has  ended.

 The use of tablets is only recommended for

models  which  offer  the  MULTI-FUNCTIONAL

TABLETS  option.

To achieve the best results from each washing

and drying cycle, powder detergent, rinse aid

liquid and salt should be used.
Compartment A: Washing detergent

Compartment B: Pre-wash detergent

1. Open cover C by pressing button
D.
2. Pour in the detergent after
consulting the Table of wash cycles:
• For powder detergent use
compartments A and B.
• For detergent in tablet form: when
the cycle requires 1 tablet, place it in
compartment A and close the cover;

when it requires 2, place the second tablet at the bottom of the
appliance.
3. Remove detergent residues from the edges of the
compartment and close the cover until it clicks.

Wash options*
The OPTIONS may only be set, modified or reset after

the wash cycle has been selected and before the
Start/Pause button has been pressed.

Only  the  options  which  are  compatible  with  the  type  of

wash cycle set may be selected. If an option is not com-

patible  with  the  selected  was  cycle  (see  Table  of  wash

cycles), the corresponding LED flashes rapidly 3 times.

If an option is selected which is incompatible with another

option or wash cycle selected previously, the incompat-

ible option light will flash 3 times and switches off, while

the most recently selected setting remains lit.

To deselect an option which has been set by mistake,

press the corresponding button again.

* Only available in selected models.

Starting the dishwasher
1. Turn the water tap on.

2. Press the ON/OFF button:  all the indicator lights on

the control panel will  light  up for a few seconds.

3. Open the door and pour in a suitable amount of

detergent (see below).

4. Load the racks (see Loading the racks) and shut the

door.

5. Select the wash cycle by turning the WASH CYCLE

SELECT knob in a clockwise direction: align the notch

on the knob with the number or symbol representing the

desired wash cycle. The START/PAUSE indicator light

will flash.
6. Select the wash options

* (see adjacent information).

7. Start the cycle by pressing the START button; the

indicator light will become green and remain lit in a fixed

manner.  The indicator light corresponding to the wash

phase will switch on, signalling that the wash cycle has

begun.

8. At the end of the wash cycle the END indicator light

will switch on (fixed green light).  Switch off the

appliance by pressing the ON/OFF button, shut off the

water valve and unplug the appliance from the electricity

socket.

9. Wait for a few minutes before removing the crockery,

in order to avoid burns. Unload the racks, beginning with

the lower level.

Modifying a wash cycle in progress

If a mistake was made during the wash cycle selection

process it is possible to change the cycle, provided that

it has only just begun: once the wash cycle has started,

switch off the machine by pressing and holding the ON/

OFF/Reset button. Switch it back on using the same
button and select the desired wash cycle and options.

Adding extra crockery

Press the Start/Pause button (the corresponding

indicator light will flash). Open the door, taking care to

avoid the escaping steam, and place the crockery inside

the appliance. Close the door and press the Start/Pause

button (fixed light): the cycle starts from the point at

which it was interrupted.

If the Start/Pause button is pressed so as to pause the

machine, the wash cycle or the Delayed Start function

(if selected) is interrupted.
At this stage it is not possible to change the wash cycle.

Accidental  interruptions

If the door is opened during the wash cycle, or if there is

a power cut, the cycle stops. It starts again from the point

at which it was interrupted once the door has been shut

or once the electricity supply is restored.

0.499465s