Hotpoint DSKS333ECWW Installation Instructions

Hotpoint Washers Installation Instructions - DSKS333ECWW.
Download
Page  of 4
4.5, 2482 votes
background image

MATERIALS YOU WILL NEED 

WARNING RISK OF FIRE

•  To reduce the risk of severe injury or death, follow all installation 

instructions.

‡&ORWKHV GU\HU LQVWDOODWLRQ PXVW EH SHUIRUPHG E\ D TXDOL¿HG

installer.

•  Install the clothes dryer according to these instructions and 

in accordance with local codes. In the absence of local codes, 

installation must comply with the NATIONAL ELECTRICAL 

CODE, ANSI/NFPA NO. 70.

•  This dryer must be exhausted to the outdoors.

•  Use only 4” rigid metal ducting for exhausting the clothes dryer to 

the outdoors.

‡'2 127 LQVWDOO D FORWKHV GU\HU ZLWK ÀH[LEOH SODVWLF GXFWLQJ

PDWHULDOV ,I ÀH[LEOH PHWDO VHPLULJLG RU IRLOW\SH GXFW LV

installed, it must be UL listed and installed in accordance with 

the instructions found in “Connecting The Dryer To House Vent” 

on page 4 of this manual. Flexible venting materials are known 

to collapse, be easily crushed, and trap lint. These conditions will 
REVWUXFWGU\HUDLUÀRZDQGLQFUHDVHWKHULVNRI¿UH

•  Do not install or store this appliance in any location where it 

could be exposed to water and or weather.

‡6DYH WKHVH LQVWUXFWLRQV ,QVWDOOHUV %H VXUH WR OHDYH WKHVH

LQVWUXFWLRQVZLWKWKHFXVWRPHU

DETERMINE ELECTRICAL REQUIREMENTS FOR YOUR DRYER MODEL

‡7KLVGU\HUPXVWEHFRQQHFWHGWRDQLQGLYLGXDOEUDQFKFLUFXLWRISURSHUYROWDJHDQGIUHTXHQF\DVVSHFL¿HGRQ5DWLQJ3ODWHORFDWHGLQVLGH

GU\HUGRRUZLWKQRRWKHUDSSOLDQFHVRU¿[WXUHVDWWDFKHG

(;&(37,21
‡$ 9 UHFHSWDFOH LV ORFDWHG RQ WKH EDFN RQ WKH GU\HU DQG LV DYDLODEOH RQO\ IRU XVH ZLWK D ZDVKHU WKDW LV DȻ[HG WR WKH GU\HU ZLWK D 

:')NLW,WPD\QRWEHXVHGIRUDQ\RWKHUDSSOLDQFHRUDQ\FRQGLWLRQVRWKHUWKDQVWDWHGDERYH99PRGHOVRQO\

‡%UDQFKFLUFXLWPXVWEHSURWHFWHGE\WKHUHTXLUHGWLPHGHOD\IXVHVRUFLUFXLWEUHDNHUV9RU9LQVWDOODWLRQDPSV9LQVWDOODWLRQRUDPSV
•  The electrical installation must conform to the national and local codes.
 

 

        208V AND 240V MODELS ARE NOT APPROVED FOR 120V INSTALLATION.

Installation Instructions (USA only)

MODELS DSKS433 AND DSKS333 MUST BE INSTALLED WITH CONTROL PANEL AT BOTTOM IN ORDER TO OPERATE ADEQUATELY.

UNPACKING AND PREPARING FOR INSTALLATION
†

Prepare the area and exhaust for installation of new dryer.

†

&KHFNDQGHQVXUHWKHH[LVWLQJH[WHUQDOH[KDXVWLVFOHDQDQGPHHWVDWWDFKHGLQVWDOODWLRQVSHFL¿FDWLRQV

†

Remove the literature and accessories bag from the dryer drum. Place the literature in a convenient place.

†

Using foam pads from dryer carton, turn dryer upside down as shown.

†

Install knobs. For location, refer to the Owner’s Manual.

†

Dryer is now ready to be mounted above washer using accessory kit.

†

Remove the foam shipping pads from under dryer.

†

Move the dryer to the desired location.

†

Follow the steps in the following pages to connect the dryer to the external exhaust and power supply.

BEFORE YOU BEGIN

Read these instructions completely and carefully.
•  

IMPORTANT- Save these instructions for local 

inspector’s use.

•  

IMPORTANT- Observe all  governing codes and 

ordinances.

•  Note to Installer -%HVXUHWROHDYHWKHVHLQVWUXFWLRQV

with the customer.

•  Note to Customer - Keep these instructions with your 

Owner’s Manual for future reference.

‡%HIRUH WKH ROG GU\HU LV UHPRYHG IURP VHUYLFH RU

discarded, remove the dryer door.

•  Service information and the wiring diagram are located 

in the control console.

•  Do not allow children on or in the appliance. Close 

supervision of children is necessary when the appliance 

is used near children.

‡,QVWDOO WKH GU\HU ZKHUH WKH WHPSHUDWXUH LV DERYH ƒ)

for satisfactory operation of the dryer control system.

•  

Product failure due to improper installation is not 

covered under the Warranty.

‡'U\HUV LQVWDOOHG LQ JDUDJHV LI DOORZHG E\ ORFDO FRGHV

PXVWEHHOHYDWHGLQFKHVFPDERYHWKHÀRRU

TOOLS YOU WILL NEED 

SLIP JOINT PLIERS FLAT BLADE AND PHILLIPS SCREWDRIVERS

GLOVES

SAFETY

GLASSES

DRYER POWER

CORD KIT

(NOT PROVIDED

WITH DRYER)

4" DUCT

CLAMPS (2)

OR

4" SPRING

CLAMPS (2)

EXHAUST

HOOD

3/4" STRAIN RELIEF

UL RECOGNIZED

4" DIA. METAL

ELBOW

4" DIA. FLEXIBLE METAL (SEMI-RIGID)

UL LISTED TRANSITION DUCT (IF NEEDED)

 KIT WX08X10077 (INCLUDES 2 ELBOWS)

4" DIA. METAL DUCT (RECOMMENDED)

4" DIA. FLEXIBLE METAL (FOIL TYPE)

UL LISTED TRANSITION DUCT (IF NEEDED.)

DUCT TAPE

UL RATED 
120/240V,30A       
WITH 3 OR 4 PRONGS. 
IDENTIFY THE PLUG 
TYPE AS PER THE 
HOUSE RECEPTACLE 
BEFORE PURCHASING 
LINE CORD. 

234D2017P001   31-16710   02-13   GE

STACKING KITS FOR DRYERS

(Comes with individual Installation Instructions)
†

 Over washer

- Use Wall Mount Kit WMK-35 or

- Stack Rack DSDR24 or

- Stack Rack DSR-24

†

 For alcove and closet depth and width 
UHTXLUHPHQWVVHHVSHFL¿FNLWLQVWUXFWLRQV

†

 All stacking kits are available from your 

local sales outlet.

Questions? Call: 800.GE.CARES (US) or visit our web site at: www.GEAppliances.com (US)

Printed in Mexico

0.528640s