Honeywell R8184G Specifications
INSTALLATION
WHEN INSTALLING THIS PRODUCT…
1. Read these instructions carefully. Failure to follow
them could damage the product or cause a hazardous
condition.
2. Check the ratings given in the instructions and on the
product to make sure the product is suitable for your
application.
3. Installer must be a trained, experienced service tech-
nician.
4. After installation is complete, check out product op-
eration as provided in these instructions.
CAUTION
1. Disconnect power before beginning installation to
prevent electrical shock or equipment damage.
2. Make sure combustion chamber is free of oil or
vapor before starting system.
R8184G PROTECTORELAY
OIL PRIMARY
APPLICATION
The TRADELINE intermittent ignition oil primary control
operates the oil burner, oil valve (if desired) and the ignition
transformer in response to a call for heat from the thermo-
stat. Through a C554 Cad Cell Flame Sensor, the R8184
monitors the burner flame and shuts down the system on
ignition failure or on flame failure during the run cycle. A light
emitting diode (LED) on the terminal strip lights when the
safety switch opens to provide safety shutdown indication.
A manual reset button is provided to reset the safety switch
after lockout.
For convenience in system maintenance, the safety
switch can be manually opened using a lever on the front of
the control. Clock thermostats that power the clock through
the primary control transformer will lose time during lockout
unless backup batteries are installed.
R8184G is component recognized by Underwriters Labo-
ratories Inc. and meets their flammability test requirements
for a final enclosure.
D.T.
Form Number 69-0617—1
Rev. 4-91
© Honeywell Inc. 1991
Fig. 1—Mounting the R8184G controls with 130
° F
[54
° C] maximum ambient temprature.
LOCATION
1. Mount on a 4 x 4 inch junction box, directly on the main
burner, or inside the appliance cabinet. In replacement
applications, mount in the same location as the old control.
2. Ensure the operating temperatures are within the am-
bient temperature range. Ambient temperature ranges are
either -40° to 130° F [-40° C to 54° C] or -40° F to 150° F
[-40° C to 66° C] (Refer to box label).
MAKE WIRING CONNECTIONS AND MOUNT CONTROL
Wiring must comply with all local codes and ordinances.
Before mounting the control, make line voltage connec-
tions as shown in Fig. 1 or 2. Splice leads with solderless
connectors. Do not exceed load ratings shown on the device
label.
If cad cell leads are run with line voltage wires, breakout
knockout at the bottom of the low voltage terminal strip and
thread can cell leads through the hole.
If necessary use control as a template to mark and drill new
mounting holes. Mount using No. 6 screws (obtain locally).
Fig. 2—Typical hookup for TRADELINE R8184G with indicator light.
CAD
CELL LEADS
LINE
VOLTAGE LEADS
MOUNTING
SCREW HOLE
RED RESET
BUTTON
4 x 4 JUNCTION
BOX
HOLE OR KNOCKOUT FOR
CAD CELL LEADS
LOW VOLTAGE
TERMINAL STRIP
1
STRIP WIRES 3/8 in. (9.5 mm); INSERT FROM SIDE, ABOVE OR BELOW.
T-T TERMINALS ON R8184G; T1-T2 TERMINALS ON R8184N.
1
2
2
M1643B
JUNCTION BOX
BLACK
L1
(HOT)
L2
LIMIT
BURNER
MOTOR
IGNITION
OIL VALVE
(OPTIONAL)
ORANGE
WHITE
BILATERAL
SWITCH
CAPACITOR
TRIAC
1K1
R2
R8184G PROTECTORELAY CONTROL
SAFETY
SWITCH
R1
1K2
M1635
SAFETY
SWITCH
HEATER
1K
CAD CELL
1
F
F
T
T
THERMOSTAT
2
LINE VOLTAGE
THERMOSTAT
2
POWER SUPPLY. PROVIDE DISCONNECT MEANS AND OVERLOAD PROTECTION AS REQUIRED.
TO USE R8184 WITH LINE VOLTAGE CONTROLLER, JUMPER T-T TERMINALS AND CONNECT LINE VOLTAGE THERMOSTAT IN
SERIES WITH LIMIT CONTROLLER.
1
2
SAFETY
SWITCH
LOCKOUT
INDICATOR
LED
Related Manuals for Honeywell R8184G
-
Honeywell Thermostats RTH2310B Owner's Manual
44 pages
-
Honeywell Thermostats TH3110D1008 Owner's Manual
16 pages
-
Honeywell Thermostats TH4110D1007 Owner's Manual
24 pages
-
Honeywell Thermostats TH6110D1005 Owner's Manual
24 pages
-
Hunter Thermostats 42999B Owner's Manual
2 pages
-
Hunter Thermostats 43054 Owner's Manual
2 pages
-
Hunter Thermostats 44100A Owner's Manual
33 pages
-
Hunter Thermostats 44100B Owner's Manual
2 pages
-
Hunter Thermostats 44155C Owner's Manual
52 pages
-
Trane Thermostats X1379088401 Owner's Manual
32 pages
-
Honeywell Thermostats T8112D Owner's Manual
8 pages
-
NOMA Thermostats THM301M User's Manual
8 pages
-
Trane Thermostats TCONT802AS32DA Instruction Manual
20 pages
-
Hunter Thermostats Thermostat 44360 User's Manual
23 pages
-
Honeywell Thermostats TH6220D1028 Owner's Manual
24 pages
-
Honeywell Thermostats TH5220D1003 Owner's Manual
20 pages
-
Honeywell Thermostats TH8321WF1001 Installation Guide
12 pages
-
Honeywell Thermostats RTHL3550D Quick Installation Guide
64 pages
-
Honeywell Thermostats RTH6580WF User's Guide
140 pages
-
Honeywell Thermostats RTH221B1039 Operating Manual
48 pages
-
Honeywell Thermostats RTH2300B1038 Operating Manual
48 pages
-
Honeywell Thermostats RTH2300B1038 Quick Installation Guide
56 pages
-
Honeywell Thermostats RTH111B1024 Quick Installation Guide
48 pages
-
Honeywell Thermostats FocusPRO 6000 Series User Manual
24 pages