Honeywell Honeywell Automobile Electronics 6160rf User's Manual

Honeywell Automobile Electronics User's Manual - Honeywell Automobile Electronics 6160rf.
Download
Page  of 4
4.9, 2470 votes
background image

 

K0903V1   2/06   Rev. B 

 

ADEMCO 6160RF

Keypad/Transceiver

Installation and Setup Guide 

 
GENERAL INFORMATION 
The ADEMCO 6160RF keypad/transceiver is a combination unit that combines the functions of the following 
devices: 
•  6160 Alphanumeric Addressable Keypad 
•  5881H RF Receiver 
•  5800TM Transmitter Module 
The 6160RF Keypad/Transceiver may be used on any control panel that supports 5800 Series wireless devices 
(e.g., VISTA-10P, VISTA-15P, VISTA-20P). 
FEATURES 
•  Supports wireless key transmitters (e.g.; 5804) and bi-directional transmitters (e.g.; 5804BD, 5828/5828V). 
•  Supports wireless keys with high-security (encryption) capability (e.g.; 5804E). 
•  Provides a nominal range of 200 feet' for RF transmitters (some transmitters have a shorter range). 
•  Supports RF jam detection when the receiver is enabled. 
•  Capable of sending status signals (Armed, Ready, etc.) to bi-directional units such as 5804BD, 5804BDV and 

5828/5828V. 

UL 

The following 5800 series transmitters are not intended for use in UL installations: 5802, 5804, 5804BD, 5804BDV, 5804E, 

5814, 5816TEMP, 5819, 5819BRS, 5819WHS, 5828/5828V and 5850. 

 
INSTALLING THE 6160RF 
Locate the 6160RF in an area and at a height where 
it is convenient for user operation. The 6160RF must 
be at least 10 ft from the control panel to ensure 
proper operation of the RF receiver. 
Mounting and Wiring 

The 6160RF has terminal blocks for connection to 
power and data wires. Removing the keypad’s case 
back provides access to the terminal blocks. 
The 6160RF can be surface mounted directly to 
walls, or to a single- or double-gang electrical box. 
Follow these steps to mount and wire the keypad: 
1.  Push the two case release snaps at the bottom of 

the keypad with the blade of a medium 
screwdriver (this will push in the release snap), 
then pull that side of the case back away. Insert 
the screwdriver in the side of the keypad 
(between the front and back case) and gently 
twist to release the side locking tab. Repeat for 
the other side. Refer to Figure 1 for location of the 
case back release snaps and locking tabs. 

ARMED

READY

MOUNTING

RELEASE

SNAPS

NOTE:
TO REMOVE REAR COVER
PUSH IN THE TWO MOUNTING
SNAPS LOCATED ALONG THE 
BOTTOM OF THE KEYPAD
AND LIFT COVER UP.

6160RF-003-V1

LOCKING

TAB

 

Figure 1.  Removing the Case Back

 

2. 

Pass the wiring from the control panel through 
the opening in the case back. (see the control 
panel’s instructions for proper run lengths.)  

a.  If surface wiring is being used, wiring may be 

routed through the top or the bottom left-side 
breakout in the case back. The breakouts must 
be punched out using a screwdriver before 
mounting the case back.  

b.  If desired, wires may be strain-relieved to the 

wire tie point on the inside of the case back 
with a tie wrap (not supplied). 

3.  Mount the case back to a wall or to an electrical 

box using the 25mm-long self-tapping screws 
supplied (mollies for drywall are not supplied).  

4. 

Connect the power and data wires from the 
control panel to the terminals on the 6160RF as 
indicated in Figure 2 and Table 1. 

 

G

6160RF-002-V1

Y +

WIRING TERMINALS

(TO CONTROL PANEL)

+ +

+ +

 

Figure 2 - 6160RF Wiring Details 

Related Manuals for Honeywell Honeywell Automobile Electronics 6160rf

0.529507s