Honeywell ADEMCO 5828 User's Manual

Honeywell Door User's Manual - ADEMCO 5828.
Download
Page  of 2
4.6, 1511 votes
background image

 

 

K0021  3/03  Rev. B 

$'(0&29

:LUHOHVV%LGLUHFWLRQDO)L[HG:RUG.H\SDG

USER GUIDE 

GENERAL INFORMATION 

The 5828 and 5828V are wireless keypads that can be 
used to operate and get status from your security 
system. The 5828 and 5828V have the following 
features (voice annunciation features apply only to the 
5828V): 
x Can be used to arm/disarm, and perform other 

system operations. 

x Can display and/or annunciate system status.  
x Can automatically display and/or annunciate a 

change in system status if AC powered (e.g., for an 
alarm, the keypad will announce the type of alarm 
(fire or burglary) and location (e.g. kitchen window). 

x Message Center can be used to record and play back 

a voice memo to yourself, or leave a message for a 
family member. 

x Can be battery- or AC-powered (AC-powered units 

have several advantages, described below).

Battery-Powered Operation:  

:KHQ SRZHUHG E\

EDWWHU\ WKH NH\SDG PXVW ILUVW EH DFWLYDWHG E\ SUHVVLQJ

DQ\ QXPEHUHG NH\ 7KH NH\SDG ZLOO GLVSOD\ WKH FXUUHQW

V\VWHP VWDWXV ZLWKLQ D IHZ VHFRQGV <RX PD\ DW DQ\

WLPH EHIRUH RU DIWHU UHFHLYLQJ VWDWXV DUP GLVDUP VHQG

D SDQLF DODUP RU SHUIRUP RWKHU V\VWHP RSHUDWLRQV 7KH

NH\SDG EHFRPHV LQDFWLYH ZKHQ QR NH\V KDYH EHHQ

SUHVVHG IRU  VHFRQGV DQG PXVW EH UHDFWLYDWHG WKH

QH[W WLPH \RX ZDQW WR XVH LW 
AC-Powered Operation: 

:KHQ SRZHUHG E\ WKH

RSWLRQDO $& DGDSWHU WKH NH\SDG UHPDLQV DFWLYH DW DOO

WLPHV RQ /\Q[5 V\VWHPV ZKHQ WKH V\VWHP LV

GLVDUPHG WKH YLVXDO GLVSOD\ ZLOO WXUQ RII DIWHU 

VHFRQGV LI WKHUH LV QR DFWLYLW\ DW WKH NH\SDG RQ /\Q[

5(1 V\VWHPV WKH GLVSOD\ UHPDLQV RQ $Q\ FKDQJH LQ

V\VWHP VWDWXV ZLOO FDXVH WKH GLVSOD\ WR DXWRPDWLFDOO\

WXUQ RQ LI EODQN DQG GLVSOD\DQQXQFLDWH WKH QHZ

VWDWXV ,I $& SRZHU LV ORVW WKH NH\SDG UHYHUWV WR

EDWWHU\SRZHUHG RSHUDWLRQ XQWLO $& SRZHU LV UHVWRUHG

DQG D QHZ VWDWXV UHTXHVW LV PDGH ✱ key

NOTE:

:KHWKHU WKH XQLW LV SRZHUHG E\ EDWWHU\ RU $&

WKH 9 PD\ WDNH D IHZ VHFRQGV WR GLVSOD\

DQGRU DQQXQFLDWH WKH QHZ VWDWXV DIWHU SUHVVLQJ WKH [✱]

NH\ 

5828V

-00-002-V0

1 OFF

4 MAX

7 INSTANT

READY

2 AWAY

5 TEST

8 CODE

0

3 STAY

6 BYPASS

9 CHIME

#

MESSAGE

MIC

ARMED

READY

RECORD

VOLUME

PLAY

STATUS

FUNCTION

VOICE

D

C

B

A

 

5828V Keypad with Front Cover Removed 

KEYPAD KEYS 

These keypads include 12-operational keys, as well as 
four Special Function keys that are backlit for ease of 
use when the keypad is active. To access the keypad 
keys, simply open the swing-down door by applying 
outward pressure on the door release slot on the right 
side.  

Panic alarms are activated by pressing the key pairs 
shown in the table below.  Special Function keys A, B, 
and C, can be programmed by your installer to provide 
the same alarms by pressing a single key and holding it 
down for 3-seconds, or can be assigned other system 
operations. (Check with your installer for the 
availability and assignment of these keys). 

 

Panic Alarm Key-

Pairs/Special Function Keys 

[1] & [

✱] or A 

[

✱] & [#] or B  

[3] & [#] or C  

SOUNDER 

The keypad’s built-in sounder pulses for fire alarms, 
and sounds continuously for burglary and audible 
panic alarms. 

HOW TO GET SYSTEM STATUS  
Turn on the keypad by pressing any numbered key. 
Status will be displayed within a few seconds. 
Additionally, on AC powered units, the keypad is 
automatically updated when a change in system status 
takes place (arming, disarming, trouble, etc.).   

HOW TO PROGRAM OR CHANGE YOUR 4-DIGIT 
SECURITY CODE 

In order to Quick Arm the system using this keypad, 
you will need to program your own 4-digit security code 
into the keypad. This code must match a code that has 
already been programmed into your control panel. To 
program the 4-digit code, perform the following steps: 

 Press the  7 INSTANT  and  9 CHIME  keys at the 

same time until the display flashes double dashes   
(- -), then release.  

 Enter the 4-digit security code that matches a valid 

user code already programmed into your control 
panel. Do NOT use the Duress Code.  There will be 
no display of the numbers you pressed. 
 

 Press  ✱ READY  to accept your entry. The keypad 

will display the system status. 

 

Related Manuals for Honeywell ADEMCO 5828

0.528488s