Honeywell 4219 - Ademco 8 Zone Expander Setup Guide

Honeywell Other Setup Guide - 4219 - Ademco 8 Zone Expander.
Download
Page  of 4
4.8, 1176 votes
background image

N8924V1  5/01 Rev. B 

 

 

4219 

Wired Zone Expander Module 

INSTALLATION AND SETUP GUIDE 

GENERAL INFORMATION 

This module adds up to eight end-of-line resistor supervised 
zones to compatible control/communicators via the control’s 
keypad wiring.   

The module may be mounted within the control’s cabinet (if 
room permits), or remotely.  If mounted remotely, there are 
provisions to tamper protect the unit.  Communication to 
the module is supervised so that it cannot be disconnected 
from the keypad wiring without detection by the control.  If 
the wiring is cut, a tamper alarm or signal will result, to 
indicate that this device (and possibly other similarly 
connected devices) has become inoperative.   

INSTALLATION 

 

1.  Power should be disconnected 

before proceeding.   

2.  Be sure to mount the 4219 before 

making any wire connections. 

When the module is mounted remotely, holes on the back of 
the module’s housing permit it to be mounted horizontally 
or vertically.  Wires can exit from the side or the breakout 
on the back of its housing.  For tamper protection, attach 
the tamper magnet (provided) (Figure 1) to the module 
inside cover.  Place the tamper jumper (Figure 2) into its 
lower position.  Affix the connections label that accompanies 
the module to the inside of the module’s cover.  When the 
installation is complete, put the modules cover on.  The 
magnet attached to the cover, positioned near the reed 
switch, will cause a tamper signal to be sent to the control if 
the cover is removed.   

When the module is to be mounted inside the control’s 
cabinet, mount it horizontally to the raised tabs at the back 
of the cabinet.  Insert self-tapping screws (provided) in two 
adjacent raised tabs at the back of the cabinet.  Leave the 
heads projecting 1/8”.  Hang the module on the screw heads 
via two slotted holes on the back of the module’s housing.  
When the module is installed in the control’s cabinet, it 
need not be tamper protected.  Place the tamper jumper 
(Figure 2) in the upper position.  Affix the connections label 
that accompanies the module to the inside of the control’s 
cover.   

S

ee the control’s installation and setup guide for additional 

information.   

CONNECTIONS AND SETTINGS 

Make protection zone connections to the module’s 12-
position  terminal  block  TB1.    Each  zone  that  is  used  must 
have a 1000-ohm end-of-line resistor connected across the 
end of its loop, as shown in Figure 1.   

CE 

For CE installations ADEMCO N6361 
EMI suppression bead is required. 

 

Refer to the N6361 installation guide for 
wire routing instructions.  
 

1. INSERT BOTTOM TABS FIRST.
2. ENGAGE TOP WITH CLIP.

4219-002-V0

 

Figure 1.  Tamper Magnet Installation 

If a zone is not programmed, the resistor need not be used.  
The method of programming each zone for the type of alarm 
and reporting code to the central monitoring station varies 
with the control to which the module is connected.  Refer to 
the Installation and Setup Guide for that control unit.   

Set the DIP Switch to one of 16 addresses, as shown in 
Figure 3, so the control can identify the module and 
communicate with it properly.  The address to be set is 
determined by the particular control to be used, and the 
control’s installation instructions must be consulted.  As 
shipped, the DIP Switch is set for an address of “0”.   

Zone A can be set for fast response time of 10ms to an open 
circuit, if desired, by setting position 1 of the DIP Switch to 
“OFF”.    As  shipped,  it  is  set  to  “ON”  for  a  response  time  of 
300ms, as shown in the table below.  All of the module’s 
other protection zones have a nominal response time of 
300ms.   

Connections to the control’s keypad wiring points can be 
made via 4-terminal block TB2 or the 4-pin plug (wire color 
connections are the same).   

SPECIFICATIONS 

 

Physical 

6-7/16”W x 4-1/4”H x 1-1/4” D 
(163mm x 108mm x 32mm) 

Electrical 

 

Input 

Voltage: 

12VDC (from control’s remote 
keypad connection points) 

Current: 30mA 

 

0.488430s