Harbor Freight Tools 1000 lb. Capacity Motorcycle Lift Product manual | Page 5
Page 5
For technical questions, please call 1-800-444-3353.
SKU 68892
9. Fit the Vise (34) to the front of the Platform using
Bolts (33), Washers (23), Lock Washers (31),
and Nuts (30). Adjust to suit the motorcycle.
note: Location of Front Wheel Vise Assembly in relation
to the Stop Plate (32) is adjustable by means of removing
Fasteners 30, 31, 23 and 33. Tighten Nuts and Bolts
only after determining the proper tire mounting position.
See Figure 4, right.
10. Attach the Stop Plate to the Platform using
Bolts (33) and Washers (23). Do not tighten yet.
11. Fit the Lift Foot Pedal (11) over the
Pump Piston Spindle (09).
12. Fit the Release Foot Pedal (10) over
the Release Valve Spindle (05).
motorcycle lift assembly (continued)
Figure 4
operating instructions
Read the EntiRE impoRtant SaFEty inFoRmation section at the beginning of this manual
including all text under subheadings therein before set up or use of this product.
1. Check and fill oil as needed. See
checking and
Filling hydraulic Fluid instructions on page 7.
2. Bleed the Lift Jack according to the
Bleeding instructions on page 7.
3. Test the Lift several times for proper operation before
attempting to lift a load.
if, after bleeding twice, the
lift still does not appear to be working properly,
do not use the lift until it has been repaired by a
qualified service technician.
Before First use
1. Position the lift on a flat, level, hard surface
able to support at least 1350 lb.
2. Turn the Lifting Screws (18) clockwise to evenly raise
the Casters (14) off the ground and limit movement.
3. With the Access Panel (36) in place, roll the
motorcycle onto the lift. Kick the center stand of
the motorcycle down to stabilize it on the lift.
4. Clamp the front wheel of the motorcycle into the
Vise Assembly to prevent movement of the wheel.
note: When properly set, front tire of motorcycle
should rest against Stop Plate (32) with the axle
centered over the Front Wheel Vise Assembly.
If not, slide Stop Plate and/or re-position wheel vise.
5. Once the Stop Plate (32) is adjusted
against the motorcycle tire, tighten the
Bolts (33) that hold it in place.
6. Secure the motorcycle to the lift using tie-down
straps (not included). See motorcycle’s owner
manual for locations of strap attachments.
7. Pump the Lift Foot Pedal (11)
repeatedly to raise the lift.
lifting
Related Manuals for Harbor Freight Tools 1000 lb. Capacity Motorcycle Lift
-
Harbor Freight Tools Lifts & Stands 1000 lb. Capacity ATV/Motorcycle Lift Product manual
12 pages
-
Harbor Freight Tools Lifts & Stands High Lift Riding Lawn Mower / ATV Lift Product manual
12 pages
-
Harbor Freight Tools Lifts & Stands 1500 lb. Capacity Vehicle Dollies 2 Pc Product manual
4 pages
-
Harbor Freight Tools Lifts & Stands 1500 lb. Capacity ATV/Motorcycle Lift Product manual
16 pages
-
Harbor Freight Tools Lifts & Stands 1000 lb. Capacity Engine Stand Product manual
8 pages
-
Harbor Freight Tools Lifts & Stands 1000 lbs. Capacity Hydraulic Table Cart Product manual
12 pages
-
Harbor Freight Tools Lifts & Stands 1000 lb. Capacity Hydraulic Table Cart Product manual
12 pages
-
Harbor Freight Tools Lifts & Stands 800 lb. Low Lift Transmission Jack Product manual
8 pages
-
Harbor Freight Tools Lifts & Stands 500 lb. Capacity Hydraulic Table Cart Product manual
8 pages
-
Harbor Freight Tools Lifts & Stands 2000 lb. Capacity Foldable Engine Stand Product manual
8 pages
-
Harbor Freight Tools Lifts & Stands 2000 lbs. Capacity Foldable Engine Stand Product manual
8 pages
-
Harbor Freight Tools Lifts & Stands 1000 Lb. Capacity Vehicle Dollies 2 Pc Product manual
4 pages
-
Harbor Freight Tools Lifts & Stands 1250 lb. Capacity Vehicle Positioning Wheel Dolly Product manual
8 pages
-
Harbor Freight Tools Lifts & Stands Motorcycle Wheel Chock Product manual
4 pages
-
Harbor Freight Tools Lifts & Stands 1800 Lb Capacity Motorcycle Stand/Wheel Chock Product manual
4 pages
-
Harbor Freight Tools Lifts & Stands 1000 lb. Capacity Engine Support Bar Product manual
8 pages
-
Harbor Freight Tools Lifts & Stands 750 lb. Capacity Engine Stand Product manual
8 pages
-
Harbor Freight Tools Lifts & Stands High Position Motorcycle Lift Product manual
13 pages
-
Harbor Freight Tools Lifts & Stands 1250 Lb Capacity Low Profile Motorcycle Dolly Product manual
8 pages
-
Harbor Freight Tools Lifts & Stands 350 Lb. Capacity Motocross Dirt Bike Stand Product manual
8 pages
-
Harbor Freight Tools Lifts & Stands 6000 Lb. Capacity Scissor Lift Product manual
17 pages
-
Harbor Freight Tools Lifts & Stands Motorcycle Wheel Cleaning Stand Product manual
3 pages
-
Harbor Freight Tools Lifts & Stands Low Profile Rear Spool Motorcycle Stand Product manual
4 pages
-
Harbor Freight Tools Lifts & Stands 1000 Lb Capacity Motorcycle Swingarm Rear Stand Product manual
5 pages