GE 57883 Wireless Outlet Receiver Owner's Manual

GE Timers Owner's Manual - 57883 Wireless Outlet Receiver.
Download
Page  of 1
4.8, 1510 votes
background image

        is a trademark of General Electric
Company and is used under license to
Jasco Products Company LLC, 10 E.
Memorial Road, Oklahoma City, OK 73114
www.jascoproducts.com

1.8125"

1.8125"

1.8125"

1.8125"

1.8125"

2.9375"

INSTRUCTION MANU

AL

Questions? Call 1-800-654-8483

WARNING

Heavy Duty Outdoor

WIRELESS OUTLET

RECEIVER

with Key Chain Transmitter

ENCLOSED YOU WILL FIND
• Outdoor Receiver
• Key Chain Transmitter
• 12-volt Alkaline Battery 

(installed)

The Receiver and the Transmitter are randomly 
preprogrammed at the factory to one of six channel 
settings. These channel settings are defined as either: A, 
B, C, D, E or F and are marked on the back of each 
product. A single GE Wireless Remote Control 
transmitter can control multiple receivers if they all have 
the same channel setting. Also, multiple GE Wireless 
Remote Control transmitters can control one receiver if 
they all have the same channel setting. 

This transmitter/receiver pair is NOT compatible with 

GE SmartHome™ remotes.
Compliance with IC Rules and Regulations
IC: 

 

3653A-R1G0030R (REMOTE) 

   

 

3653A-PT446A (RECEIVER)

Company:    

Jasco Products Company

Model Number: 

R1G0030R (REMOTE)

   

 

PT-448B (RECEIVER)

Object is subjected to the following two conditions.
This device may not cause interference, and this device must accept 
any interference, including interference that may cause undesired 
operation of the device.

This class B digital apparatus complies with Canadian ICES-003.

OPERATING INSTRUCTIONS
1. Plug Outdoor Receiver into a GFCI protected 

receptacle. Make sure unit hangs freely with 
receptacle down and away from wet locations.

2. Plug light or appliance into Outdoor Receiver.
3. Make sure outlet supplying Outdoor Receiver is 

powered.

4. Make sure light or appliance is turned ON.

IMPORTANT: The lamp or appliance will 

remain OFF until the Outdoor Receiver is 

activated by the Transmitter.

You can now control your lamp or appliance 
remotely using the Transmitter. A light on 
the Outdoor Receiver turns on when the 
unit is activated remotely, indicating that 
power is being supplied to the lamp or 
appliance.

IMPORTANT: Make sure to press toggle 

button on Transmitter firmly for a minimum 

of 1 second for best results.

A light on the Key Chain Transmitter turns on when the 
toggle button is activated, indicating that an ON or OFF 
signal is being sent. If indicator light is not activated by 
pressing the toggle switch, replace the battery (USE 
ONLY 12V type A23 Alkaline).

REPLACING BATTERY
1.Remove battery cover.
2.Remove old battery.
3.Install new 12V type A23 alkaline battery noting 

polarity.

4.Replace battery cover.

SPECIFICATIONS:
OUTDOOR RECEIVER

FOR INDOOR USE ONLY

CAUTION: DO NOT EXCEED ELECTRICAL RATINGS

Functional Range ....................................up to 100ft
Maximum Resistive Load ............................ 1440W
Maximum Tungsten Load .............................. 1000W
Rating ..................... 120V, 60Hz 1/3 HP Motor Load

KEY CHAIN TRANSMITTER

CAUTION: DO NOT EXCEED ELECTRICAL RATINGS
Functional Range ....................................up to 100ft
Battery Type ................ Use only 12V Alkaline A23

* Functional range may be adversely affected by one or 
more of the following factors: weather, radio frequency 
interference, low transmitter battery and obstructions 
between the transmitter and receiver.

This device complies with part 15 of the FCC rules. Operation is subject to the 
following two conditions: (1) this device may not cause harmful interference, and 
(2) this device must accept any interference received, including interference that 
may cause undesired operation.
FCC NOTE: The manufacturer is not responsible for any radio or TV interference 
caused by unauthorized modifications to this equipment. Such modifications 
could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a class B 
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to 
provide reasonable protection against harmful interference in a residential 
installation. This equipment generates, uses and can radiate radio frequency 
energy and, if not installed and used in accordance with the instructions, may 
cause harmful interference to radio communications. However, there is no 
guarantee that interference will not occur in a particular installation. If this 
equipment does cause harmful interference to radio or television reception, 
which can be determined by turning the equipment off and on, the user is 
encouraged to try to correct the interference by one or more of the following 
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which 

the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

0

15259-2  rev. 11.12.09

Risk of electric shock
• Keep children away
• Do not use in wet locations
• Fully insert plug
• When used outdoors, plug directly into 

a GFCI Protected electrical outlet

Risk of fire
• Do not exceed electrical ratings

Related Manuals for GE 57883 Wireless Outlet Receiver

0.584874s