GE 19248 Door Chime With Pictures Coming Soon Owner's Manual

GE Door Owner's Manual - 19248 Door Chime With Pictures Coming Soon.
Download
Page  of 2
4.1, 1317 votes
background image

 
 

Wireless Door Chime 

Figure 3MountingholelocationsBatterycompartmentMelodyselectionbuttonPushbutton 

Installation Instructions  
Required tools: Small flat blade screwdriver, #2 Phillips screwdriver and 1/16” 
and 3/32” drill bit (not included)
 
The wireless door chime kit has two components: 
Installing battery in push button 
1. Remove the front cover of the push button housing by pushing a flat blade 

screwdriver into the slot at the bottom of the push button housing (See Figure 1)

2. Install the CR2032 battery (included) with the positive(+) side up. 
3. Keep the front cover off the push button until melody selection is complete. 
Pairing the transmitter push button(s) to chime receiver 
NOTE: the chime and push button(s) come paired in the package. Once batteries are 
installed in the push button and chime, press the push button(s) to ensure the chime 
sounds.  
IF CHIME DOES NOT SOUND, FOLLOW DIRECTIONS BELOW TO PAIR THE 
PUSH BUTTON(S) TO THE CHIME. 
1. 

To clear settings: Press and hold the Pairing button on the bottom of the chime 
while installing the third battery. 

2. 

Once the last battery is installed, release the pairing button. 

3. 

Press and hold the Pairing button again. You will hear the “Ding Dong” melody 
twice, and then the double beep to alert you the chime is ready to pair with the 
push button. Release the Pairing button. 

4. 

Press and release the push button (See Figure 1). You will hear one beep 
letting you know the chime accepted the signal.  

5. 

Wait 10 seconds and you will hear the double beep again to alert you the chime 
is now paired with the push button. 

6. 

Press the push button to test.  

 
Melody Selection Setting (your chime will have either 2 or 8 melodies) 
Select the melody by pushing the melody selection button located inside the push 
button housing (See Figure 1). Press and release the melody selection button until 
you hear the desired melody. Table 1 and Table 2 shows the order the melodies will 
be heard. 
The last melody played will be your selected chime melody. 
Volume Adjustment 
There are three volume settings on this chime: high, medium and low. 
1. 

To adjust the volume, press and release the pairing button on the chime or push 
the push button to play the melody 

2. 

While melody is playing, press and release the volume button on the chime to 
select the desired sound level. 

 
Push Button Mounting Instructions 
NOTE: Avoid mounting on metal surfaces, as it may result in a reduced range of 
transmission. Do not mount in an area exposed to direct rain. Push buttons are 
typically mounted at the same height as the door knob or handle (between 36” and 44” 
above the floor). 

1. Remove the front cover of the push button(See Figure 1)
2. Before mounting, choose a mounting location that is no further than 150 feet 
from the chime unit location. Place the push button where you would like to mount 
and test with the chime as close to its final location as possible. If it works, continue 
with mounting the button. If it does not work, see TROUBLESHOOTING. 
3. Drill two holes with 1/16”drill bit in the marked mounting hole locations (See 
Figure 3)

4. With arrow on the back plate pointing up, secure the back plate to the mounting 
surface with the two 2x12mm screws included. 
5. Press front housing onto back cover. 
6. Test operation. If chime does not work, see TROUBLESHOOTING. 

Chime Mounting Instructions 

NOTE: Avoid mounting on metal surfaces, as it may result in a reduced range of 

reception. 
1. 

Select chime mounting location. 

2. 

Using the chime mounting template on the package insert card, drill two holes 
with 3/32”drill bit in marked keyhole slot locations (See Figure 2)

3. 

Insert the two 3x25mm screws included, into the holes, setting the screw heads 
extending about ¼” from mounting surface. 

4. 

Place th

e chime unit’s keyhole slots over the screws and press down on the 

chime unit to secure it. 

 

Troubleshooting 

If the chime does not work: 
1. Make sure push button switch is pressed down and held for at least 1 second. 
2. Verify battery installation is correct, noting polarity. 
3. Try a fresh battery in push button. 
4. Make sure chime is no further than 150 feet away from push button. 
5. Ensure push button is not mounted on metal, near metal studs, or near the floor. 
6. Try a new location for the chime. 

Functional range may be adversely affected by one or more of the following factors: 
weather, radio frequency interference, low transmitter battery and obstructions 
between the transmitter and receiver. 
This device complies with part 15 of the FCC rules. Operation is subject to the 
following two conditions: 

(1) this device may not cause harmful interference, and (2) this device must accept 
any interference received, including interference that may cause undesired 
operation. 

FCC NOTE: The manufacturer is not responsible for any radio or TV interference 
caused by unauthorized modifications to this equipment. Such modifications could 
void the user’s authority to operate the equipment. 
NOTE: This equipment has been tested and found to comply with the limits for a Class 
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to 
provide reasonable protection against harmful interference in a residential installation. 
This equipment generates, uses and can radiate radio frequency energy and, if not 
installed and used in accordance with the instructions may cause harmful interference 
to radio communications. However, there is no guarantee that interference will not 
occur in a particular installation. If this equipment does cause harmful interference to 
radio or television reception, which can be determined by turning the equipment off 
and on, the user is encourage to try to correct the interference by one or more of the 
following measures: 

• Reorient or relocate the receiving antenna. 
• Increase the separation between the equipment and receiver. 
• Connect the equipment into an outlet on a circuit different from that to which the 
receiver is connected. 
• Consult the dealer or an experienced radio/TV technician for help. 

MADE IN CHINA 

GE is a trademark of General Electric Company and is under license by 
Jasco Products Company LLC, 10 E. Memorial Rd., Oklahoma City, OK 
73114. 

This Jasco product comes with a 90-day limited warranty. Visit 
www.jascoproducts.com for warranty details and product registration.  

Questions? Contact us at 1-800-654-8483 between 7:30AM

—5:00PM CST.  

Push Button (Transmitter) Figure 

1PushbuttonMountingholelocationsBatterycompartmentMelodyselectionbuttonPushbuttonPush flat blade screw driver 

intothe slot to open the cover 

Chime (Receiver) Figure 2pairingvolumeKeyholeslot 

Table 1 - 2 Melody Chime  

1 Dingdong 
2 Westminster 
Table 2 - 8 Melody Chime  

1 Dingdong 
2 Westminster 
3 Knocks (3 times) 
4 Fanfare 
5 Mozart 
6 Good Vibes 
7 Patriotic 
8 Tango 

19248 
19297 
19303 

Versión 02 

07/31/2013  

Related Manuals for GE 19248 Door Chime With Pictures Coming Soon

0.601975s