GE 19211 GE Wireless SevenSound Lighted Push Button Owner's Manual

GE Door Owner's Manual - 19211 GE Wireless SevenSound Lighted Push Button.
Download
Page  of 2
4.2, 1017 votes
background image

If you do not want to drill holes in your door frame, 

you can use the supplied double sided tape for 

installation.

1. Clean all mounting surfaces with a 50/50 mixture 

of isopropyl alcohol.

2. Remove the backing from one side of the double 

sided tape and press the exposed side against the 

back plate of the push button.

3. Remove the other backing strip and press the 

exposed side against the door frame where you 

want the button installed.

Operation

1. Turn on the chime.

2. Gently press transmitter button to sound chime.

Troubleshooting

Chime doesn’t work:

1. Make sure push button switch is depressed and 

held for at least 1 second.

2.  Make sure house code switches 1-4 on chime and 

push button match exactly.

3. Verify battery orientation in push button.

4. Try fresh batteries.

5. Make sure chime is not farther than 150 feet away 

from push button.

6. Ensure push button is not mounted on metal, near 

metal studs, or near the floor. 

7.  Try a new location for the chime.

Functional range may be adversely affected by one 

or more of the following factors: weather, radio 

frequency interference, low transmitter battery and 

obstructions between the transmitter and receiver.

This device complies with Part 15 of the FCC rules. 

Operation is subject to the following conditions:

1. This device may not cause harmful interference, 

and

2. This device must accept interference received, 

including any interference that may cause 

undesired operation. 

For technical support contact Jasco Products 

Company at 1-800-654-8483 

or www.jascoproducts.com

Made in China

Hecho en China

  is a trademark of 

General Electric Company 

and is used under license to 

Jasco Products Company LLC, 

10 E. Memorial Road, 

Oklahoma City, OK 73114. 

www.jascoproducts.com

Rev 4-07                                                                        

                                19211

GE Model 19211

www.jascoproducts.com

     

Wireless Lighted 

Pushbutton 

Included Hardware: 

(2) 3x20mm screws

(2) Double sided adhesive pads

Required Tools: Small flat blade screwdriver, drill, 

1/16” drill bit, and phillips screwdriver.

 

Installing or Changing Batteries

1. Remove back cover.

2. Install the (included) Two CR2032 

batteries in the clear plastic battery 

holder located inside the push button.

3. Be sure the positive (‘+’) side of each battery is 

facing upwards.

4. Slide each battery under the metal clip and gently 

push down to secure each battery.

5. To remove the batteries gently pull back on the 

plastic battery clip until the top battery pops - up.

6. Be sure to change both batteries when replacing 

batteries.

Chime Tune Setting

All wireless chimes may have more than one push 

button. The chime tune for each push button is set 

with dip switches 1-3.

Single Push Button Kit:  If you purchased a kit with 

a single push button, the chime tune will be set to 

Ding Dong from the factory.

Dual Push Button Kit:  If you purchased a kit with 

two push buttons, one push button will be set to 

Ding Dong and the other push button will be set to 

Westminster from the factory.   

The following instructions explain how to change the 

tune on any wireless push button.

1.  Remove the cover from the pushbutton.

2. Remove the battery from the push button 

transmitter.

3. Locate the 3 dip switches shown below.

4. Select the desired chime sound from the table 

below.

Chime Sound Table

Position   

3

Westminster 

ON 

OFF 

OFF

Ding Dong 

OFF 

ON 

OFF

Knock             

OFF 

OFF 

ON

Bronze Chime      

ON 

ON 

OFF

Cuckoo Clock      

ON 

OFF 

ON

Foghorn            

OFF 

ON 

ON

Gong              

ON 

ON 

ON

ON:   Switch On

OFF: Switch Off

Pushbutton Dip Switches and Jumpers

Setting The House Security Code 

Each chime component has 4 jumpers for setting the 

house security code. In most cases you will not need 

to change the factory settings for the house security 

code.  If your chime activates intermittently or does 

not work at all, you may be able to solve the problem 

by changing your security code.

1. Remove power or batteries from the chime.

2. To remove the batteries from the pushbutton, open 

the pushbutton case as shown below.

3. Locate the House Security Code door and screw 

located  on the back of the chime.  Remove the 

screw and take off the door.

4. Locate the chime and pushbutton jumpers shown 

below.

Chime and Pushbutton Jumpers

5. To change the house code, add or remove jumpers 

as needed.  It is recommended to change only 

one jumper at a time and then test the system for 

proper operation. The jumpers on the chime and 

pushbutton must match exactly.

If you have an older chime with 6 jumper positions, 

remove jumpers from the 5th and 6th positions in the 

chime and match the jumpers exactly on positions 1 to 

4 on the chime and pushbutton. See the picture below

Older Chime with New Pushbutton

Push Button Mounting Instructions 

Note: Avoid mounting on metal surfaces, as it may 

result in a reduced range of transmission.  Do not 

mount in an area where exposed to direct rain.

a. Removing the back cover

b. Replacing the back cover

1. Push buttons are typically mounted at the same 

height as the door knob or handle (between 36” and 

44” above the floor).

2. Before mounting, choose a mounting location that 

is not farther than 150 feet from the chime unit 

location. 

 

Not farther than 150 feet

Place push button where you would like to mount 

and test operation with the chime as close to it’s final 

location as possible.  If it works, mount button here. If 

it does not work, see TROUBLESHOOTING. 

3. Use back cover of push button as a template to 

mark two screw holes.

4. Drill two holes with 1/16” drill in marked 

locations.

5.  Secure back cover to the mounting surface with the 

3x20mm screws.

6.  Press front housing onto back cover.

7.  Test Operations, if chime does not work, see 

TROUBLESHOOTING.

House Code Jumpers

Chime Dip Switches

Positions 5 and 6 open. Position 

1 to 4 match exactly.

Related Manuals for GE 19211 GE Wireless SevenSound Lighted Push Button

0.587969s