Garmin StreetPilot 2820 Quick Reference Guide

Garmin GPS Quick Reference Guide - StreetPilot 2820.
Download
Page  of 2
4.9, 1652 votes
background image

 Configure your StreetPilot 2820.

1.  Flip the power switch down to turn on your 2820. 
2.  Follow the screen prompts to configure the 2820; you only have to do this once.

 Pair your cellular phone with Bluetooth® wireless technology to your StreetPilot 2820.

1.  Press the 

MENU key. 

2.  Touch 

Settings > Bluetooth > Manage Connections

3.  If you have never paired a device with your 2820, touch 

Yes. If you have already paired a device with your 2820 and want 

to add another, touch 

Add Device

4.  Set your phone to “Find Me,” “Discoverable,” or “Visible” mode. Touch 

OK on the 2820. 

5.  Touch your device in the list. 
6.  If your phone model appears in the list, touch it. If not, touch 

Other Phones….

7.  When pairing your phone, enter the 2820’s PIN code (1234) 

into your phone when prompted. 

8.  From the Main menu, touch 

Phone. Use the Mobile Phone 

menu to place calls and review your call history. 

  NOTE: You must have the external microphone connected or a 

headset with Bluetooth wireless technology paired to your 2820 in order to place a call.

Finding a Destination

➋  Touch Food, Hotel….

➌  Touch 

 and 

Recreation.

➊  Touch Where To?

➍  Touch a category.

➏  Touch Go To.

➎  Touch a place.

Following Your Route

Follow the route to your destination using the map. As you travel, your 

2820 guides you to your destination with voice prompts, arrows, and 

directions along the top of the map. If you depart from the original 

route, your 2820 recalculates the route and provides new route 

instructions.

WARNING: For use in vehicles, it is the sole responsibility of the owner/operator of a vehicle with the 2820 installed to place and secure the device so it does 

not interfere with the vehicle operating controls and safety devices, obstruct the driver’s view of driving conditions, or cause personal injury in the event of an 

accident.

Getting Your StreetPilot 2820 Ready
To use the mounting base with adhesive disks, start with 

➊. To use the non-skid friction mount, start with ➋.

➊ Attach the mounting base to your dashboard.

1.  Clean and dry the area where you want to place the mounting 

base. 

2.  Remove the liner from the bottom of the base. 
3.  With the locking lever facing you, position the base on the cleaned 

area. Apply pressure to adhere the base to the dashboard. 

 Mount your StreetPilot 2820 to the base.

1.  Align the power plug on the vehicle adapter to the connector and 

slide the plug until fully seated.

2.  Slide the locking lever on the base to the left (unlocked).
3.  Slide the bottom of the 2820 into the base until it clicks into place. 
4.  Slide the locking lever to the right (locked). 
5.  Plug the power cable into a 12-Volt receptacle in your vehicle. 
6.  Route the cable so it does not interfere with vehicle operation.

© Copyright 2006 Garmin Ltd. or its subsidiaries

May 2006 

190-00633-01 Rev. B 

Printed in Taiwan

Your route is marked with a magenta line.

Follow the arrows.

A checkered 

flag marks your 

destination.

StreetPilot® 2820

setup and go!

Mobile Phone menu

Indicates your 

cellular phone’s 

battery level and 

signal strength

Power 

plug

Locking lever

Release tab

Mounting 

base

Power 

switch

0.482781s