Garmin GPSMAP 8208 MFD Quick Start Manual

Garmin GPS Quick Start Manual - GPSMAP 8208 MFD.
Download
Page  of 14
4.7, 1027 votes
background image

GPSMAP® 8000 Series Installation 

Instructions

Important Safety Information

 WARNING

See the Important Safety and Product Information guide in the 

product box for product warnings and other important 

information.
When connecting the power cable, do not remove the in-line 

fuse holder. To prevent the possibility of injury or product 

damage caused by fire or overheating, the appropriate fuse 

must be in place as indicated in the product specifications. In 

addition, connecting the power cable without the appropriate 

fuse in place will void the product warranty.

 CAUTION

Always wear safety goggles, ear protection, and a dust mask 

when drilling, cutting, or sanding.

NOTICE

When drilling or cutting, always check what is on the opposite 

side of the surface.

Registering Your Device
Help us better support you by completing our online registration 

today.
• Go to http://my.garmin.com.
• Keep the original sales receipt, or a photocopy, in a safe 

place.

Contacting Garmin Product Support
• Go to www.garmin.com/support and click Contact Support 

for in-country support information.

• In the USA, call (913) 397.8200 or (800) 800.1020.
• In the UK, call 0808 2380000.
• In Europe, call +44 (0) 870.8501241.

Tools Needed
• Drill and drill bits
• #2 Phillips screwdriver
• Marine sealant
• Jigsaw
• File and sandpaper

Mounting the Components
Mounting Considerations

NOTICE

This device should be mounted in a location that is not exposed 

to extreme temperatures or conditions. The temperature range 

for this device is listed in the product specifications. Extended 

exposure to temperatures exceeding the specified temperature 

range, in storage or operating conditions, may cause device 

failure. Extreme-temperature-induced damage and related 

consequences are not covered by the warranty.

You can mount the device using one of three methods. You can 

use the included bracket and hardware to bail mount the device, 

you can use the included template and hardware to flush mount 

the device, or you can use the flat-mount kit (sold separately) to 

mount the device flat with the dashboard. When selecting a 

mounting location, observe these considerations.
NOTE: Not all mounting methods are available for all device 

models. See the specific mounting-type section for more details 

about your model.
• The location should provide optimal viewing as you operate 

your boat.

• The location should allow for easy access to all device 

interfaces, such as the keypad, touchscreen, and card 

reader, if applicable.

• The location must be strong enough to support the weight of 

the device and protect it from excessive vibration or shock.

• To avoid interference with a magnetic compass, the device 

should not be installed closer to a compass than the 

compass-safe distance value listed in the product 

specifications.

• The location must allow room for the routing and connection 

of the cables.

Bail Mounting the Device

NOTICE

If you are mounting the bracket on fiberglass with screws, it is 

recommended to use a countersink bit to drill a clearance 

counterbore through only the top gel-coat layer. This will help to 

avoid any cracking in the gel-coat layer when the screws are 

tightened.

The bail-mounting hardware (screws and washers or nuts, 

washers, and bolts) is not included. The holes on the bail-mount 

bracket are 5/16 in. (7.9 mm) in diameter. Before you can bail 

mount the device, you must choose mounting hardware that fits 

the holes in the bail-mount bracket and securely attaches it to 

your specific mounting surface. The size of the pilot hole 

required depends on the mounting hardware you choose.
You can bail mount only the eight-inch and 12-inch models. Due 

to the size of the 15-inch models, you must install them using 

the flush-mount or flat-mount method.
Using the included bail-mount bracket 

À

 as a template, mark 

the location of the four pilot holes 

Á

.

Using a drill bit appropriate for your mounting hardware, drill 

the pilot holes.

Secure the bail-mount bracket to the surface using your 

mounting hardware 

Â

.

Install the bail-mount knobs 

Ã

 on the sides of the device.

December 2012

190-01557-02_0A

Printed in Taiwan

0.496785s